Woodturning Online Videos


Welcome to the Woodturning Online Videos page.

This video content was created by woodturner, Rick Morris. He has created a way to monitor all the videos in YouTube that are woodturning related.

Each month, Rick updates the video listings below. If you would like to learn about new videos, sign up for our free newsletter where we will list the top 20 videos each month.

Any categories in BOLD have sub-categories to help you narrow down your search.

Bowl Categories

 

Bowls from Boards Videos (18)

Sort by

Or click here to: Search All Videos


Bowl from a Board ·
By: Steve Lindsley
April 02, 2017 · 14,856 views

I wanted to try and make a bowl from a board that had a little flair to it. I've used this technique to make a bowl in the past but it was from a solid piece of wood. For this project I glued up some scrap into a board. I was inspired by a chapter in Jim Rogers' book 'The Fundamentals of Segmented Wood Turning'. Jim goes over most of what's in the book on his Craftsy video. I'll put a link below. If you already know how to make a bowl from a board then this video probably won't tell you anything new. If you've not attempted a bowl from a board maybe this video will be helpful. I'm sure there are plenty of others on YouTube as well. I hope you enjoy the video. Comments are always welcome. Thanks! Steve https://www.craftsy.com/woodworking/shop/woodworking-classes

 

Inner Lipped Pallet Bowl - Episode 15 ·
By: Paul Lockwood
July 26, 2016 · 1,411 views

Using nothing but Pallet wood this project took a lot of preperation hours. Two pallets were stripped at work during lunchtimes. Fortunatley one of these the slats were all hardwood. Over a course of another couple of days all the slats and supports were then planed down (link below). These were then cut to find the best pieces of timber and over the course of the next 4 days were glued together to create the blanks. With the softwood being so soft the main worry was the blank spinning off a worm screw. As a backup I could use a faceplate, but I've never used one so far. Working towards the h

 

Shiplap Bowl - Episode 9 ·
By: Paul Lockwood
July 01, 2016 · 643 views

Sticking with my usual soft wood, this time I have used a 3M length of shiplap board. Ripping this down into 200x65mm lengths and gluing them together to create the final blank. Preparation work took place over three days to produce the blank before it finally went on the lathe. Even though this is soft wood, the turning was very slow and hard work. There was tear out at times mainly because of trying to take too much out at a time. The final finish was very smooth and clean and I am very pleased with the final result which had two coats of sanding sealer and woodwax 22. Link to Woodturner21 https://www.youtube.com/user/woodturner21/feed Please Subscribe http://www.youtube.com/channel/UCJmcpalJi_xzP_iV3uXJj2w?sub_confirmation 1

 

Shiplap Pieces - Episode 6 ·
By: Paul Lockwood
June 22, 2016 · 227 views

Using scraps of Shiplap boards, I glued these together to create one blank. Chopping the corners off on the mitre saw and then mounting on the lathe via the worm screw. Surprisingly these turned pretty well. There was very little tear out and where it did have a smooth surface was a great finish. Only sanded to 240 grit as this is a softwood. Please Subscribe http://www.youtube.com/channel/UCJmcpalJi_xzP_iV3uXJj2w?sub_confirmation 1

 

Ray Lanham - Making a bowl from a board ·
By: Ocean Woodturners
April 25, 2015 · 732 views

Ray Lanham demonstrates making a segmented bowl from a single board at the Ocean Woodturners April 2015 meeting in Providence, RI.

 

Single Board Bowl -- and announcing a giveaway for the donators of my channel. ·
By: PeteTGIF
February 22, 2015 · 3,439 views

This weeks project is a Single Board Bowl. Or as Cip from Cip's Wood Chips called it, an Economy Bowl. Here's the link to his video and how he made it. http://youtu.be/VBAZjWlljLE ----------------------------------------------------- In orrer to help my channel and my therapy running, please donate via my homepage: http://thankgoditsfriday.de/html/donations.html As I'd like to give something back to you, I'll make a 'giveaway' in 4 weeks time. On March 22nd, everyone who donated 10 EUR will be in the drawing. At the moment there's my Teelight Candle Holder from Outer Space in as a prize, but

 

Turning a Solid Timber Bowl ·
By: MrD Burke
December 22, 2014 · 45 views

This is a demonstration video of turning a timber bowl from a solid blank. It's the first time I tried using a glued paper method for attaching the blank to the faceplate. As you'll see, it has it's positives & negatives, but I think that the positives wins, as it allowed me to rescue this project from a mishap. While I have edited this video down somewhat, it is a long video, but I've tried to show the whole process from raw blank to finished bowl. I took solace from the guys on the Woodtalk podcast that instructional videos should be exactly that & short-cutting what you see doesn't always help people to see the craft that is woodwork. I hope you enjoy this video & find parts of it helpful & educational.

 

Bowl from a Board using Baltic Birch Plywood with a Weave Style ·
By: Tom Lohman
October 14, 2014 · 57,313 views

This video shows the steps to build a bowl from a board with a basket weave look out of a piece of Baltic Birch Plywood.

 

Bowl from a board ·
By: Roger Meeker
March 17, 2014 · 393 views

Detroit Area Woodturners presents: Roger LaRose and 'A Bowl from a Board'

 

ALFREDO LEISER'S HOBBY- BOWL FROM A BOARD. 3 BOWLS, THE FIRST WITH DEMONSTRATION ( 2 years turner) ·
By: alfredo leiser
September 10, 2013 · 237 views

יצרתי את הסרטון הזה בעזרת יוצר המצגות של YouTube (http://www.youtube.com/upload)

 

Three Minute Bowl From Board ·
By: Williamoyoung
September 04, 2012 · 7,251 views

Bowl rings cut from board in less than three minutes

 

Turning a Bowl From A Board ·
By: DentonTurners
August 09, 2012 · 79,519 views

Joel Rubin shows us how to cut and glue up sections from a flat board to create a turned bowl. Joel demonstrated this technique at the August 2012 meeting of the Golden Triangle Woodturners in Denton, Texas. Find More information on the club at: www.goldentrianglewoodturners.org

 

One Board Bowl (economy bowl) Wood Turning ·
By: Mark Hammond
November 12, 2011 · 108,826 views

A little how to for woodturning a one board bowl. Some call them economy bowls.

 

True Economy 9 - Wrap-up ·
By: Bob Hamilton
September 30, 2009 · 11,942 views

This is segment #9 of 9 of a companion video for my article on turning a bowl from a board. The illustrated article as well as other articles are located on my website at: http://bobhamswwing.com/index_of_articles.htm

 

True Economy 5 - Glue up & Initial turning ·
By: Bob Hamilton
September 30, 2009 · 22,805 views

This is segment #5 of 9 of a companion video for my article on turning a bowl from a board. The illustrated article as well as other articles are located on my website at: http://bobhamswwing.com/index_of_articles.htm

 

True Economy 4 - Initial assembly & mounting recess ·
By: Bob Hamilton
September 30, 2009 · 14,770 views

This is segment #4 of 9 of a companion video for my article on turning a bowl from a board. The illustrated article as well as other articles are located on my website at: http://bobhamswwing.com/index_of_articles.htm

 

True Economy 3 - Cutting the half rings ·
By: Bob Hamilton
September 30, 2009 · 16,516 views

This is segment #3 of 9 of a companion video for my article on turning a bowl from a board. The illustrated article as well as other articles are located on my website at: http://bobhamswwing.com/index_of_articles.htm

 

True Economy 2 - Layout & Cutting ·
By: Bob Hamilton
September 30, 2009 · 16,773 views

This is segment #2 of 9 of a companion video for my article on turning a bowl from a board. The illustrated article as well as other articles are located on my website at: http://bobhamswwing.com/index_of_articles.htm

 

Return to Turning Videos

Great Bargains


Heavy Duty Live Center

On Sale for only $16.53

List Price: $19.95

Click here for more information or to purchase

 


Dremel Rotary Tool Kit

On Sale for only $139.00

Save $60.99 (30%)

List price: $199.99

Click here for more information or to purchase


Roller Stand

On Sale for only $23.79

Save $6.11 (20%)

List Price: $29.90

Click here for more information or to purchase

 


Easy Wood Tools - Easy Start Rougher + Finisher + Detailer

On Sale for only $159.99

List price: $206.97

These tools have the smaller 9" maple handle and are 12.5" overall.

Click here for more information or to purchase


NOVA 48232 G3 Reversible Wood Turning Chuck

On Sale for only $99.00

Save $60.99 (38%)

List price: $159.99

Click here for more information or to purchase

Powered by Google

Our Newsletter

We update our home page about monthly to feature a new project, a new article, and a new and hot tool. Then we create a newsletter to alert our subscribers.
We never let anyone use our list, and our subscribers have been wonderfully loyal as a result.

We hope you will try it out!

Sign Up For Our Newsletter

A Sampling of our Sponsors:
(Visit the Vendor's Corner above to see all our sponsors)

The Studios' of Bradley R.M.
Backgate
Sheffield Woodturning

(Click any Ad to go to our Sponsor's Website)