Woodturning Online Videos


Welcome to the Woodturning Online Videos page.

This video content was created by woodturner, Rick Morris. He has created a way to monitor all the videos in YouTube that are woodturning related.

Each month, Rick updates the video listings below. If you would like to learn about new videos, sign up for our free newsletter where we will list the top 20 videos each month.

Any categories in BOLD have sub-categories to help you narrow down your search.

Segmented Turning Videos (166)

Sort by

Or click here to: Search All Videos


Segmented Rings with Trapezoid Shaped Wedges ·
By: SIS Woodworking
October 17, 2017 · 5,386 views

This video demonstrated the production of trapezoid shaped wedges for incorporation in segmented rings in wood turning projects. These wedges are produced on the band saw utilizing the Accu-Wedge system by tilting the band saw table 10 degrees. This video details the process of producing these wedges and segmented rings. Finally we demonstrate the slicing of the segmented wedges to produce unique pattern feature rings for you woodturning projects.

 

Indexing Wheels for Segmented Turners ·
By: Ron Brown
September 23, 2017 · 560 views

Ron demonstrated indexing wheels segmented turners use to align segmented rings. More info at www.ronbrownsbest.com

 

Open Segmented Gluing Station Jig Parts ·
By: Tom Lohman
September 15, 2017 · 1,424 views

This video details the jig parts that I make for sale so you can make a gluing jig for segmented projects

 

Cutting Accurate Segmented Wedges on the Accu-Wedge ·
By: SIS Woodworking
September 05, 2017 · 542 views

This video describes the setup of the band saw, the Accu-Slice and the Accu-Wedge system to produce accurate segmented wedges on the band saw. This video guides the operator through the various parameters needed to achieve the best results including the selection of the band saw blades, clamping of the wood to be cut, and adjustment of the Accu-Wedge system.

 

Accu-Wedge Segmenting Carriage with Wide Boards to Produce Large Segmented Discs ·
By: SIS Woodworking
August 31, 2017 · 369 views

The Accu-Wedge Segmenting Carriage is used to cut segments from wide boards to produce large diameter segmented discs. Segmented discs consisting of 12 segments per ring were produced from boards 4' to 6' wide to produce 8' to 12' diameter segmented discs with no center gap.

 

Woodturning at 54a. #125 My simple start up guide to segments. ·
By: Keith Barrow
August 08, 2017 · 4,552 views

I've had a few questions about measuring and calculating segments,so here's an easy to follow method. For your seggy set or centre finder,please go to: http://www.woodturningat54a.com For Yorkshire Grit: http://www.yorkshire-grit.com/ For Hampshire Sheen products: http://www.hampshiresheen.com

 

Gluing Segmented Rings with Epoxy Resins ·
By: SIS Woodworking
July 27, 2017 · 1,043 views

This video demonstrates some techniques for the gluing of segmented rings with epoxy resin glues. Using epoxy resins to glue the wood segments together produces stronger glue joints and minimizes the chance of open segment joints in glued segment rings in segmented wood turning projects. Since the epoxy resin is not water based, the wood segments don't adsorb any water from the glue which could cause the wood segments to shrink and crack in the future. Due to the slow setting time for the epoxy resins, segments can be easily adjusted before the rings are left to harden overnight.

 

making a sunrise feature ring ·
By: earl's small segment shop
July 25, 2017 · 3,714 views

sunrise feature ring for segment turning

 

Accu-Wedge - The Auto-Indexing Table ·
By: SIS Woodworking
July 18, 2017 · 1,004 views

This video describes the Auto-Indexing Table for the Accu-Wedge System. The Accu-Wedge uses two fences. Index points are machined into the Accu-Wedge table into which the fences lock in position. This enables the user to select from 4 to 72 segment per ring selections for making segmented rings on the band saw without any math or calculation and without the use of wedges or angles. The fences snap into position for producing accurate segmented rings with perfect joints between the segments of the rings. 17 possible segments per ring selections, including 5, 7 and 9 segments per ring. For additional details visit our web site at: www.accu-slice.com

 

Accu-Wedge Band Saw Blade Selection ·
By: SIS Woodworking
July 18, 2017 · 1,001 views

The selection of the proper band saw blade is critical for the optimum operation of the Accu-Wedge. This video demonstrates that the 3/4' x 14 tpi Timber Wolf band saw blades provide for the production of perfect segmented wood discs on the band saw. Segmented discs can be cut with the Accu-Wedge system on the band saw with segmented rings from 4 up to 72 segments per ring. Completely closed segmented ring with no center hole are easily cut on the band saw using these techniques. Additional details at: www.accu-slice.com

 

Accu Wedge - Cutting Wood Segments on the Band Saw ·
By: SIS Woodworking
July 18, 2017 · 1,695 views

The Accu-Wedge system has been developed for the cutting of segmented wedges on the band saw to make segmented wood discs and eventually projects such as segmented wood bowls. Cutting the wedges uses the double fence system much like the wedgie technique used on the table saw. The Accu-Wedge has an auto-indexing table for the production of segmented discs from 4 up to 72 segments per disc in 17 steps. No need for wedgies since the auto-indexing table is precision machined with index stops to produce the selected number of segments with no calculation, no measuring and no fine adjustment. Cutting the segments on the band saw wastes less wood and is much safer than cutting them on the table saw. Additional details at: www.accu-slice.com

 

3D Printed Spacer ·
By: Bostin Bowls
July 15, 2017 · 33 views

A time-lapse of my spacer being 3D printed. Designed and printed by my friend Mark.com.

 

missing segment turning ·
By: earl's small segment shop
July 03, 2017 · 701 views

making a missing segment turning open segment

 

criss cross open segment turning ·
By: earl's small segment shop
June 20, 2017 · 787 views

open segment build with criss cross pattern

 

Better Gluing Surface ·
By: Gord Rock
June 18, 2017 · 1,284 views

Using a material that glue will not stick to, for gluing segmented rings and other projects.

 

Feature Rings - June 2017 ·
By: BayLake Woodturners
June 17, 2017 · 1,365 views

Feature Rings in Segmented Turnings The presentation for our June, 2017 meeting was done by Gerald Jensen. He discussed the jigs he uses to cut and build feature rings for his segmented bowls and vessels. Recorded June 17, 2017 at the NWTC Artisan Center, 1417 Cedar Street, Green Bay, WI 54302

 

Introducing the Accu Wedge Segmenting Jig for the Bandsaw ·
By: SIS Woodworking
May 31, 2017 · 1,065 views

A new device called the Accu-Wedge has been developed to enable the cutting of segmenting wedges on the band saw. The wedges for segmented bowls can now be cut on the band saw, resulting in less wasted wood and a much safer method than using a table saw. The Accu-Wedge uses the double fence method for cutting the wedges, but it incorporates an auto indexing system that does not require wedgies or angles. This jig will be called the Accu-Wedge and the prototype version will be demonstrated at the AAW meeting in Kansas City on June 23-25, 2017. The Accu-Wedge is constructed from a 5/16 inch

 

basic segment ring construction ·
By: earl's small segment shop
May 01, 2017 · 2,513 views

Three ways to make segment rings

 

3d feature ring build ·
By: earl's small segment shop
April 24, 2017 · 2,587 views

3d feature ring for segment turning

 

Drechseln einer Urne aus Zwetschge/Ahorn in Segmenttechnik ·
By: Linden Drechsler
April 10, 2017 · 7,926 views

Drechseln einer Schmuckurne aus Zwetschge und Ahorn

 

easy open segment turning 32 segments per ring ·
By: earl's small segment shop
April 09, 2017 · 2,125 views

Easy to make open segment turning using 32 segments in each ring

 

Floating Segmented Bowl ·
By: Kyle Toth
April 07, 2017 · 79,044 views

This is not my 100th bowl but it was an experiment to see how the floating device worked and how much weight it could hold. I have a larger magnet that will support a few pounds and will be making a larger bowl for that. The segmented bowl is made in Walnut and ebony. If you would like to support me and help me make more videos check out https://www.patreon.com/woodbytoth I also post shop update videos of what i'm working on. All the support I can get really helps me out and allows me to take the time to film the things that I get to build! Thanks! For inquiries and commissions contact woo

 

floating bottom for segment turning ·
By: earl's small segment shop
March 22, 2017 · 2,208 views

making a floating bottom for segmented turning

 

open segment glue up jig build ·
By: earl's small segment shop
March 19, 2017 · 1,384 views

Making a jig to glue on open segments

 

Segmented Filler Rings ·
By: SIS Woodworking
March 18, 2017 · 4,334 views

This video describes the design and production of segmented wood rings that will be used as designer or filler rings in other projects such as our Segmented Wood Eggs.

 

Index system for open segment ·
By: earl's small segment shop
March 14, 2017 · 2,066 views

Making index wheel/system for open segment turnings

 

dot to dot trim ring the easy way ·
By: earl's small segment shop
March 13, 2017 · 3,266 views

making a dot to dot trim ring the easy way

 

segment ring clamp ·
By: earl's small segment shop
March 11, 2017 · 5,199 views

Clamp for gluing segment rings

 

Woodturning at 54a. #112. How I make a Seggy with 3D printing. ·
By: Keith Barrow
March 01, 2017 · 4,939 views

A short video about the process of making a wedge for segmented turning,or 'Seggy',as I like to call them! This involves the use of the computer,and a 3D printer. Please take a look at my new website,it's not up to much yet,but I'll keep adding and improving things . www.spanglefish.com/woodturningat54a www.yorkshire-grit.com www.hampshiresheen.com www.ukiws.co.uk

 

patternringyoutube ·
By: Segmentedturning
February 26, 2017 · 1,344 views

Another simple pattern ring.

 

small turning open segment 2 size segments ·
By: earl's small segment shop
February 23, 2017 · 1,404 views

making a small open segment turning with 2 size segments

 

Бывают огорчения (No luck) ·
By: Аleksey Bek
February 15, 2017 · 3,337 views

В конце работы треснула заготовка. Причина одна, надо делать люнет. Длинные детали без него не сделаешь. Проклеим по новой и доделаем до конца. At the end of the cracked piece. The reason to do the holder. Long parts without it will not. The work will be done.

 

open segment turning getting started ·
By: earl's small segment shop
February 13, 2017 · 3,055 views

constructing an open segment turning, making an index wheel and gluing platform, cutting open segments, gluing open segments. Making basic turning.

 

MiterSet- Cut Perfect Miter Angles And Segments ·
By: Carl Jacobson
January 16, 2017 · 4,334 views

The MiterSet is the easiest way to set up your miter gauge. Cut perfect miters and segments every time with this jig. Here's a link were you can find the MiterSet, https://miterset.myshopify.com/?aff 22 I upload a new project video every Friday, and I'm live Monday, Wednesday, and Friday. Check out my Twitch channel. https://www.twitch.tv/carljacobson I upload a new project video every Friday. Thank you for supporting free woodworking My Etsy shop https://www.etsy.com/shop/Thewoodshoptv Patreon, I really appreciate your support. https://www.patreon.com/CarlJacob

 

Segmented Bowl Centering Press ·
By: Rough Cut Creations
January 09, 2017 · 2,635 views

Came up with this baby to make centering and clamping bowls a lot easier. Partially inspired by the Woodturner PRO Segment Stomper. https://www.youtube.com/watch?v LS6TnFWVXVk

 

30 Plans for Segment PRO, visit segmentedturning.org. ·
By: Tom Lohman
January 06, 2017 · 3,626 views

30 plans to build bowls shown on this video

 

Introduction to Segmented Woodturning - Part 2 of 2 ·
By: Gwinnett Woodworkers
December 21, 2016 · 15,438 views

Allen Money demonstrates his techniques for segmented woodturning. Allen provides a detailed staged demonstration with detailed slides of each step. Click here to watch episode 1: https://youtu.be/F28xhgclHdU Recorded and presented in HD 10-13-2016 Follow Us: Facebook - https://www.facebook.com/gwinnettwoodworkers Google - https://plus.google.com/u/0/108617881849470980915 Twitter - https://twitter.com/gwinnettwoodwkr Website - http://www.gwinnettwoodworkers.com Music licensed to Gwinnett Woodworkers Association by Pond5.com item #26177787 'Holiday Acoustic Guitar'.

 

Introduction to Segmented Woodturning Part 1 of 2 ·
By: Gwinnett Woodworkers
December 21, 2016 · 30,328 views

Allen Money demonstrates his techniques for segmented woodturning. Allen provides a staged demonstration with detailed slides of each step. Click here to watch Part 2: https://youtu.be/KbV98j3bY8g Recorded and presented in HD 10-13-2016 Follow Us: Facebook - https://www.facebook.com/gwinnettwoodworkers Google - https://plus.google.com/u/0/108617881849470980915 Twitter - https://twitter.com/gwinnettwoodwkr Website - http://www.gwinnettwoodworkers.com Music licensed to Gwinnett Woodworkers Association by Pond5.com item #26177787 'Holiday Acoustic Guitar'.

 

Baseball Bat made of 1283 Pieces!!! with Zig Zag Pattern ·
By: Fiaschetti Woodworking
October 30, 2016 · 32,858 views

This piece is available for purchase at http://www.fiaschettiwoodworking.com/ Go check out Frank Howarth's Bat: https://youtu.be/4cazESXWTic In this video I make my second baseball bat. It is made of walnut (the darkest wood) ash (the lightest wood) and yellow heart (the yellow wood). There are a total of 1283 pieces that make up this Bat. The length is 32' and the barrel size is 2 5/8'. This bat is for sale If you are interested in purchasing this piece or have any questions please email me at fiaschettiwoodworking@gmail.com

 

Wedgie Sled (Segmented Turning) ·
By: BayLake Woodturners
September 17, 2016 · 7,318 views

Describes use of the 'Wedgie Sled', the 'Stomper', and a somewhat unique jig for gluing up segments. Recorded at the NWTC Artisan Center, Green Bay, Wisconsin on September 17, 2016. For details on the 'Wedgie Sled' and the 'Stomper', see http:/www.segeasy.com Several people asked about the table saw throat plate with replaceable inserts. It is based on a set of plans by Ralph Bagnall, the Consulting Woodworker ( http://consultingwoodworker.com/plans_store - 7.99 ). The plans detail a throat plate for a Delta Unisaw, but they are easy to adapt to other saws.

 

Segment Turning Part 2 (Turning) ·
By: Maple-Crossing Woodworks
September 05, 2016 · 1,795 views

This video picks up where we left off last time (cutting and gluing) and starts the turning process on a segment bowl. The segment rings are Cherry with a Bloodwood accent ring. The base is solid Cherry.

 

Segmented Ring Press ·
By: Turntastic Wood Designs
June 25, 2016 · 2,064 views

A press for clamping rings of a segmented bowl or vase

 

John Kershner demonstrates the assembly of segmented bowls ·
By: Mid-Maryland Woodturners Club
June 14, 2016 · 788 views

At the May 2016 meeting of the Mid-Maryland Wood Turners Club, John Kershner demonstrates the cutting and assembly of intricate segmented bowls and vases. Equipment and jigs: Multiple species of hardwood (at least three) Cutting jig Digital angle scale (recommended) Drum sander (recommended) Lathe (of course).

 

13 - Hipster Coffee Shop People... Segment Sled Follow Up ·
By: Peter Matthew 2
June 07, 2016 · 124 views

Jay Bates: http://jayscustomcreations.com My Website: http://www.peterturnswood.com Main Channel: https://www.youtube.com/channel/UCMCVIk6zuSQNsbhdcPhfiBA Contact me: peterturnswood@gmail.com

 

Segmenting Sled ·
By: Peter Matthew
June 03, 2016 · 1,858 views

Watch and see how I made a segmenting sled! www.peterturnswood.com ----------------------------------------­­­---------- To see my vlog and follow-up channel, go to my main channel by clicking 'Peter Matthew' up above. On my main channel, look to the right side of the screen where it says 'Featured Channels'. Under 'Featured Channels' is 'Peter Matthew 2'. Click that and subscribe to that channel :) ----------------------------------------­­­­­­­­­­­­­­­­­­-----------------------­-­-­-­-­-­-­-­-­-­-­-­-­-­-­-­- Want to do a sticker swap? Send me an email: peterturnswood@gmail.com Want to send me stuff? Mailing address: Peter Matthew 6388 East Executive Drive Westland, MI 48185 Contact me: peterturnswood@gmail.com My eBay store: http://www.ebay.com/usr/dste6080 Subscribe to my YouTube Channel! I post videos every Friday!

 

Small Stock Jointing Sled (Bonus Video) ·
By: RJBWoodTurner
May 29, 2016 · 2,163 views

I made this sled once before but I made it from MDF. I use the sled on most of my projects and the MDF didn't hold up. I have a project I'm preparing for next week and I needed this sled to make it happen. Regards, Bob Link to Original Video: https://youtu.be/G42RvaoBjDs Facebook: https://www.facebook.com/pages/RJBWoodturner/992853487406788 E-Mail: RJBWoodturner@ufoww.com Address for Shop Stickers: P.O. Box 114 Newburgh, IN 47629-0114

 

How I've Cut 70,000 Pieces ·
By: Kyle Toth
May 16, 2016 · 179,282 views

Tools I use: Dewalt Chop Saw- http://amzn.to/2eKXmvH Subscribe to my channel https://www.youtube.com/channel/UCn_4fr5sKRorFuq479M7Kig?view_as subscriber This video is about cutting segmented pieces for vases and bowls. For inquiries and commissions contact woodbytoth@gmail.com To keep up with my work throughout the week check out the links below. Thanks for watching! Love Tōth Also if you want to know why I love what I do check out my artist profile video done by Vigil Films. Its part of there Ardent Collection.... http://youtu.be/JjUzuECZN-0 http://www.woodbytoth.com https://m.facebook.com/woodbytoth https://mobile.twitter.com/woodbytoth http://instagram.com/tothtoth Support: https://www.patreon.com/woodbytoth Store: http://woodbytoth.bigcartel.com For a Dusty Life T-Shirt check out https://thedustylife.com

 

Laying Out a Segmented Turning ·
By: Steve Lindsley
May 15, 2016 · 3,594 views

I've received several questions over the past couple of years on how I go about laying out my segmented turnings. I'd like to say that I use some sophisticated software program but I don't. It starts we me, a pencil, paper, a ruler and a calculator. There are a lot of different ways to arrive at the same end result this just happens to be the way I do it. If you're interested search on YouTube for other videos on this topic. I'm sure you'll find plenty. If you have any questions or comments please leave them below. Thanks for watching!

 

Segmented Wedgies ·
By: Turntastic Wood Designs
April 09, 2016 · 1,410 views

An easier and more accurate way to make the pieces for segmented turning was developed by Jerry Bennett. Check out his channel here https://www.youtube.com/channel/UCd8Qkm6R7002yQSKu-o1Vog

 

How To Make a Segmenting Sled Part 2 ·
By: Lynn Lacey
March 26, 2016 · 3,209 views

How to make a pen blank segmenting sled. In Part 2 we'll look at how this sled is equipped and used to make cutting segments versatile, safe and repeatable with the use of angled inserts. Add another dimension to your pen making with this sled. Instagram www.instagram.com/LL_Woodworks www.ll-woodworks.net

 

Open segment jig ·
By: Rebel Turner
March 25, 2016 · 3,477 views

I decided to make an open segment jig for those of you who like to DIY jigs. you can either buy one online of make it yourself. Have fun. Like and share. Thanks for watching.

 

I Got Wedgie's! ·
By: Carl Jacobson
February 22, 2016 · 27,798 views

I started working on some segmented turnings. The Seg-Easy sled makes segmented turning so easy. Seg-Easy Jerry Bennett http://www.segeasy.com/wedgies.htm Bob Blanford https://www.youtube.com/user/RJBWoodTurner IKI Woodturners http://ikiwoodturners.blogspot.com/ DrexlFlo ceiling light https://www.youtube.com/channel/UCBi_KUPVKJGeM5wTpYteYcA I upload a new project video every Friday. Thank you for supporting free woodworking My Etsy shop https://www.etsy.com/shop/Thewoodshoptv Patreon https://www.patreon.com/CarlJacobson Schedule one-on-one online classes jaco

 

Segmented Wood turning Box Design ·
By: Chris Wilson
February 22, 2016 · 336 views

Segmented Container

 

E28 - Win a Segmented Bowl Kit! 4000 Subs Giveaway! ·
By: M. Saban Smith Woodturning
February 19, 2016 · 1,554 views

This week, you can win one of the segmented bowl kits I've been talking about recently from new company Wood You Believe It in my 4000 subscriber giveaway. Click below to enter, but watch the video first! Entries close on the morning of 26th February (GMT). To enter, visit: http://www.msabansmith.com/2016/02/19/4k-bowl-kit-giveaway/ and visit Leon at Wood You Believe it at http://www.wood-youbelieveit.co.uk This giveaway/contest is not associated with, supported by, endorsed by or affiliated with YouTube. For full rules, see the website at http://www.msabansmith.com You can read more abou

 

A Few Segmenting Tips ·
By: Carl Jacobson
January 25, 2016 · 9,583 views

This was my first segmented piece, and I learned a few tip that might help you. Yuval Lahav https://www.youtube.com/user/yuvallahav Woodturner Pro http://woodturnerpro.com/ Segmented turnings http://www.segmentedturning.com/ I upload a new project video every Friday. Thank you for supporting free woodworking Patreon https://www.patreon.com/CarlJacobson Schedule one-on-one online classes jacobson68@yahoo.com Robust Woodturning Tools http://www.turnrobust.com/ Easy Wood Tools http://www.easywoodtools.com/ ChefwareKits https://www.chefwarekits.com/?tracking c

 

Cutting Segments on a Wedgie Sled ·
By: Steve Lindsley
January 22, 2016 · 47,326 views

Using plans provide on Jerry Bennett's website I built this wedgie sled, a zero clearance insert and a stop. Jerry's website is: http://www.segeasy.com/ He also has a YouTube videos on how to build and use the sled to cut segments. His YouTube channel is: https://www.youtube.com/channel/UCd8Qkm6R7002yQSKu-o1Vog If you're interested in segmented turning this sled is worth a look. It will be my go to sled for any future segmented projects.

 

Perfect Segments Every Time/Wedgie Sled ·
By: Carl Jacobson
January 18, 2016 · 85,068 views

If segmentation is something you're interested in, do yourself a favor and make this sled. It will save you a lot of headaches.This is Jerry Bennett's from segeasy design, and cost about 30 to build. Jerry Bennett https://www.youtube.com/channel/UCd8Qkm6R7002yQSKu-o1Vog Jerry's website www.segeasy.com Here's a link to some of the tools I used in this video, http://astore.amazon.com/thewood0c-20 I upload a new project video every Friday. Thank you for supporting free woodworking My Etsy shop https://www.etsy.com/shop/Thewoodshoptv Patreon, I really appreciate

 

Making the perfect sled by Al Furtado ·
By: Rebel Turner
January 01, 2016 · 1,064 views

How to make a perfect sled that makes your compound segmented turning a breeze as well as any rings with unlimited options

 

Video #5 Segmenting Sled For The Bandsaw ·
By: AnkleBiter Woodworks
November 27, 2015 · 2,772 views

Building of a segmenting sled for my 17' band saw. Fairly simple construction with positive stops at the angles for typical numbers of segments. As always: comments and suggestions are welcome! Don't forget to subscribe! Like us on Facebook: https://www.facebook.com/anklebiterwoodworks Visit our website: https://www.anklebiterwoodworks.com

 

Segmented Woodturning and the Pantorouter ·
By: bach thanh
November 22, 2015 · 691 views

 

A simple trick for using a clamp to glue segment sections ·
By: SegmentedTurner
October 26, 2015 · 4,016 views

Using a very simple and easy to make 'shoe' you can use a standard bar clamp to hold segment sections for a bowl tight while gluing them together.

 

Quicker & Easier Segmented Rings ·
By: Gord Rock
October 04, 2015 · 5,823 views

An easier way to make Segmented Rings To order Wedgies: http://www.segeasy.com/toystore2.htm Jerry Bennett's channel: https://www.youtube.com/channel/UCd8Qkm6R7002yQSKu-o1Vog Making the Wedgie Sled: https://www.youtube.com/watch?v hpFNE1CHsc4

 

Segmented Overview ·
By: Turntastic Wood Designs
August 24, 2015 · 1,314 views

A basic overview of how I make segmented bowls and vases.

 

Segmented Bowl Feature Ring ·
By: Somers Woodturning
July 11, 2015 · 1,009 views

What type of wood is in this feature ring?

 

Tommy Akridge segmented Wood Turning ·
By: Tommy Akridge Designs
May 14, 2015 · 78,696 views

This video is about Tommy Akridge Designs Wood turning

 

Calculate segment lenghts Al Furtado ·
By: Rebel Turner
May 03, 2015 · 4,847 views

I use this formula to calculate my segment lengths very easy and accurate. I hope this eases any confusion on how big to cut a segment for any size ring.

 

Patterned Segmented Bowl ·
By: Cip's Wood Chips
April 30, 2015 · 20,568 views

Here it is the end of April and this is the first bowl I made this year. This bowl is my first bowl with a inlayed pattern look. It is mostly made from rings and parts left over from learning to make segmented bowls.

 

Free Style Segmented Bowl Turning Part 2 by Al Furtado ·
By: Rebel Turner
March 23, 2015 · 7,197 views

Free Style Segmented Bowl Part 2 I might have come up with a new way to segment a bowl and making it very economical bowl with awesome design options that do not limit you.t his is a non traditional approach to segmented turning.

 

Free Style Segmented Bowl part 1 Assembly by Al Furtado ·
By: Rebel Turner
March 23, 2015 · 11,736 views

Free Style Segmented Bowl I might have come up with a new way to segment a bowl and making it very economical bowl with awesome design options that do not limit you. I eliminated the glue time of rings and trueing them up in between rings. This video is the assembly and I will be uploading part 2 the turning.

 

MineoDemo215 ·
By: Dallasarea Woodturners
March 06, 2015 · 499 views

Simplified segmenting instructions for turned, segmented bowls and boxes

 

Miter sled that will ease your segment turning ·
By: Rebel Turner
March 02, 2015 · 22,242 views

I made this miter sled with the intentions of it containing much needed information for easy ring creation as well as sophisticated compound miter rings. this is an all in one combination sled that will ease your segment turning.

 

Indian Blanket Design For Segmented Turning ·
By: Gord Rock
February 28, 2015 · 89,488 views

How to make an Indian Design Feature Ring for a Segmented Vessel or Bowl.

 

Segmented segment ·
By: Gordon Millar
February 17, 2015 · 113 views

Making pictures in solid wood to include in the segments of a turned fruit bowl

 

#116 Segmentado de doble angulo 2 Double bevel segmented turning 2 ·
By: Miguel Sanchez
February 02, 2015 · 19,801 views

Ayuda al canal: www.patreon.com/miguelsanchez Help the channel: www.patreon.com/miguelsanchez Tabla de angulos: http://www.tornoartesano.es/files/DuelasPlanilla.pdf Tabla de angulos: http://www.tornoartesano.es/files/Tabladecortesdobleangulo.xls Libro de segmentado: http://www.tornoartesano.es/files/libro-de-torneado-segmentado_1.pdf Gracias a: Hector Oscar Bocconi, Claudio Fraga y Adenilson Salmo da Silva http://www.facebook.com/profile.php?id 1181903663 http://www.tornoartesano.es miguel@tornoartesano.es

 

#115 Segmentado de doble angulo 1 Double bevel segmented turning 1 ·
By: Miguel Sanchez
February 02, 2015 · 26,181 views

Ayuda al canal: www.patreon.com/miguelsanchez Help the channel: www.patreon.com/miguelsanchez Tabla de angulos: http://www.tornoartesano.es/files/Tabladecortesdobleangulo.xls Tabla de angulos: http://www.tornoartesano.es/files/DuelasPlanilla.pdf Libro de segmentado: http://www.tornoartesano.es/files/libro-de-torneado-segmentado_1.pdf Gracias a: Hector Oscar Bocconi, Claudio Fraga y Adenilson Salmo da Silva http://www.facebook.com/profile.php?id 1181903663 http://www.tornoartesano.es miguel@tornoartesano.es

 

#108 Nueva prensa de encolar - New gluing press ·
By: Miguel Sanchez
December 30, 2014 · 73,358 views

Ayuda al canal: www.patreon.com/miguelsanchez Help the channel: www.patreon.com/miguelsanchez Una nueva version de la prensa para encolar, finalmente el coste llego a unos 26 dolares, 4 y algo mas de lo previsto pero aun interesante. Espero que os guste http://www.facebook.com/profile.php?id 1181903663 http://www.tornoartesano.es miguel@tornoartesano.es

 

How To Get Tight Segmented Joints ·
By: Ridgeway Woodcraft
December 27, 2014 · 3,657 views

A video showing the Ridgeway Woodcraft preferred method of getting tight joints in a segmented wood ring.

 

Segment Sanding ·
By: Gordon Millar
November 14, 2014 · 206 views

The making of a Segmented Bowl

 

#49 My Adjustable and Repeatable Segmenting Sled ·
By: Stephen Ogle
September 30, 2014 · 22,220 views

Answering questions about my segmenting miter sled which is very accurate and repeatable after the initial setup. See Brian Higgins's sled at: https://www.youtube.com/watch?v _C9R4IByV1Q

 

Great way to glue wooden segments together ·
By: Fosscreations
September 27, 2014 · 4,420 views

How to glue small odd shaped pieces of wood together without clamps for a segmented the wood turning.

 

How to make a segmented wood turning ·
By: Fosscreations
September 27, 2014 · 275 views

Getting wood segments ready for gluing.

 

Woodturning - Aspen Segmented Bowl - The Complete Process ·
By: Kevin Krull
September 25, 2014 · 20,913 views

For this video I'll be showing the complete process that I use to make a simple segmented bowl. The wood that I'm using is Aspen, from a board, aka 'flat-wood'. The Aspen has some amazing curly figure that has to be seen, in person, to be appreciated.

 

Off Center Segment Experiment (sawdust rd. woodshop) ·
By: Johnny Boudreau
September 24, 2014 · 140 views

Well some say insanity is doing the same thing over and over again and expecting different results, with that said lets see what happens this time... I started by segmenting a piece of mahogany between two pieces of maple, then I proceeded to make cut slicing through the segment and added another mahogany segment to the equation. As I am still working on my multiple axis turning I decided to persevere and bring you yet another multi axis bottle, or flower holding device if you wish. Thanks for watching. Johnny Music by Rusty Guitard ; https://www.youtube.com/channel/UCdI608okmTH4hkw3b30MBsQ

 

Segmented Woodturning To Fix My Mother's Old Stone Clock ·
By: As Wood Turns
July 17, 2014 · 2,651 views

http://www.AsWoodTurns.com Sometimes the best project is a simple project to help someone else in a small but critical way. This is the case with this project. My mother has a sentimental attachment to a stone clock that her brother in law made for her many, many years ago. Unfortunately the clock stopped working. Testing revealed that the problem was the movement. I wished it had been the cord that would have been easy to replace. Searches at local stores and internet sources could not find a similar movement - one that plugged into a wall socket. Searches for a battery operated movement cou

 

Compound Segment Jig ·
By: Rebel Turner
June 10, 2014 · 1,829 views

This compound segment jig is accurate and adaptable to any segments you might need to create

 

Segmented Woodturning Plans Using MS Powerpoint (Bonus Video) ·
By: As Wood Turns
May 21, 2014 · 3,666 views

http://www.AsWoodTurns.com I've had many request for more information on how I use Microsoft Powerpoint to plan my segmented woodturning projects. This video shows the advanced features I employ. This video is only for those already familiar with Powerpoint. It assumes you understand basic operations and only need a little bit more of an edge so you can use Powerpoint in this manner. This video shows how to create a master template that can be used over and over for many projects. As a master template, you will not accidentally select, move, delete the background grid while you create the dra

 

Wood Turning - Segmented Goblet ·
By: Mike Waldt
April 30, 2014 · 70,241 views

I go through the process of turning a Staved or Segmented Goblet, using Amazique, Purple Heart and Acacia. Inspired by Bob Pritchard of Woodgoblets.com. Here are the links to Carl Jacobson and The Tin Guitar by Michael Berk : https://www.youtube.com/user/mikeberk810

 

A Guide to Stave Construction for Woodworking and Woodturning ·
By: Gord Rock
March 29, 2014 · 184,690 views

Stave construction is a great way to make cylinders without needing to buy large dimension wood. This is a simple method very easily accomplished.

 

segmented turning 3 ·
By: 이종현
March 25, 2014 · 507 views

YouTube 동영상 편집기(http://www.youtube.com/editor)를 이용하여 동영상을 만들었습니다.

 

segmented turning 2 ·
By: 이종현
March 25, 2014 · 471 views

이 동영상은 YouTube 슬라이드 쇼 제작 도구(http://www.youtube.com/upload)로 만들었습니다.

 

segmented turning - hardmaple bottle ·
By: 이종현
March 25, 2014 · 768 views

...

 

Woodturning Segmented Valentine's Candy Heart Box ·
By: As Wood Turns
February 06, 2014 · 4,011 views

http://www.AsWoodTurns.com How do I turn a heart on a lathe? I need one for Valentine's Day. Everything around Valentine's day seems to require some form of a heart. I wonder why! This candy box is segmented red oak. It has a 104 segments: 2 lids with 24 segments each; the body has 56 segments. After adding the 2 finials, 106 pieces of wood make up this heart shaped candy box. Because it holds editable items, I finished it with beeswax and mineral oil. So - a heart shaped box - no problem. I'm ready for Valentine's Day. Enter your email at http://www.AsWoodTurns.com & I'll let you know when the next easy woodturning project video is ready.

 

# 212 Segments, Segment II ·
By: Cap'n Eddie Castelin
January 27, 2014 · 25,791 views

This is he second in a series for segments. Big Guy Productions and Capt. Eddie Castelin are at it again. Contact Cap'n Eddie at eddiecastelin@cox.net or www.eddiecastelin.com

 

# 211 simple segment ·
By: Cap'n Eddie Castelin
January 26, 2014 · 20,326 views

I have wanted to do another segment program, I broke this up into at least 3 pieces. This is the first. Big Guy Productions and Capt. Eddie Castelin are at it again. Contact Cap'n Eddie at eddiecastelin@cox.net or www.eddiecastelin.com

 

The making of Metamorph. A segmented woodturning solution. ·
By: SegmentedTurner
January 13, 2014 · 16,398 views

This is a slide show of how I turned a 3' square by 8' long piece of ash into a segmented shallow bowl with an elevated foot.

 

woodturning segmented ağaç torna ·
By: Ahmet Ozkaraaslan
January 04, 2014 · 1,462 views

yūzlerce parçadan oluşan eserler

 

Thehandsonwoodworker Part4GluingStaveTypeSegments118 ·
By: The Hands-On Woodworker
December 04, 2013 · 150 views

 

Dubby Sled: "Cutting Pieces for Segmented Woodturning Projects" ·
By: PeachtreeWoodworks
November 14, 2013 · 22,151 views

The inventor of the highly acclaimed woodworking cut-off sled shows you how to cut pieces for segmented turning projects using the Dubby Cut-Off Sled. For more info about the Dubby System, Click link below... http://www.ptreeusa.com/dubby_details.htm

 

Segmented Turning - Grain Orientation Options ·
By: SegmentedTurner
September 02, 2013 · 35,986 views

One of the options available in segmented turning is the orientation of the wood grain to optimize both visual impact and ease of turning. In this video I show how to keep that in mind when assembling your cut segments.

 

SPP Usage 8 Diamonds ·
By: William Kandler
June 01, 2013 · 2,605 views

How to adorn your segmented turning project with Diamonds in the Segmented Project Planner

 

SPP Usage 7 ZigZags ·
By: William Kandler
June 01, 2013 · 2,321 views

How to adorn your segmented turning project with ZigZags using the Segmented Project Planner

 

SPP Usage 6 Solid Colors ·
By: William Kandler
June 01, 2013 · 1,822 views

How to adorne you segmented project using solid colored wood in the Segmented Project Planner

 

SPP Usage 5 Layer Tuner ·
By: William Kandler
June 01, 2013 · 1,999 views

How to use the Segmented Project Planner's Layer Tuner to make fine adjustments of your segmented project design

 

SPP Usage 3 Main Dialog ·
By: William Kandler
June 01, 2013 · 2,772 views

How to user the main dialog of the Segmented Project Planner to develop your segmented project design

 

SPP Usage 11 Open Segments & Spacers ·
By: William Kandler
June 01, 2013 · 3,235 views

How to add/modify Vertical Spacers or Open Segment features to your segmented turning project with the Segmented Project Planner

 

2012-10-13 Segmentation and Intarsia by George North (41m33s) ·
By: Gwinnett Woodworkers
March 04, 2013 · 15,614 views

GWA Classs 10-13-12 GWA Member George North identifies the differences between segmentation and intarsia using samples and answering audience questions. He discusses gluing and taping techniques along with pattern transfer. Full Video (41:32:33) Filmed and uploaded in HD

 

12 Steps to Segmented Turning Excellence: Step 4 - Setting the Number of Sides ·
By: William Kandler
January 17, 2013 · 4,203 views

The number of segments per ring depends on your preference and the size of the object. The larger the ring, the more segments needed to keep turning running smooth. 8 sides works well for 6' diameter and smaller. Then use 12 for up to 10' or so. You can step all over this one depending on exactly what you're doing. Just remember when you turn, 1/2 of each segment is cutting generally, and roughly, up hill and then the last half is a very comfortable smooth down hill. Commonly, the number of segments is consistent throughout the piece, but you can use a variable number if it makes sense to the structure of the piece.

 

12 Steps to Segmented Turning Excellence: Step 3 - Set the Wall ·
By: William Kandler
December 29, 2012 · 3,268 views

Now that you have a good shape/form and its size, establish an even wall thickness throughout the piece. It's OK to be a little heavier down lower for stability.

 

12 Steps to Segmented Turning Excellence: Step 2 - Determine Project Size ·
By: William Kandler
December 28, 2012 · 3,212 views

Establish your object size. There aren't any rules here. Just make it a size that's appropriate to its intended use or where you'll display it.

 

12 Steps to Segmented Turning Excellence: Step 1 - Establish the Project Shape ·
By: William Kandler
December 27, 2012 · 6,361 views

Form is KING. Establish it first. Compound curves are nice; just be sure to smoothly transition from one to the next. Your form can be tall and skinny or short and wide. While developing your form/shape, pay no attention to size. Remember, form is KING. If you need help with proportions, remember the Golden Mean (.618) or the photographer's 1/3, 2/3 rule. Use it for height to width and for positioning the maximum diameter point. The base diameter can be 20% to 30% of the maximum diameter for artistic pieces and more for utilitarian pieces. Plates/platters need a larger base, 50% or more of the diameter.

 

sled for cutting segments on bandsaw ·
By: Segmentedturning
December 17, 2012 · 7,166 views

Hello again, In this video I just go through how I make my sleds for cutting the segments on my bandsaw. The process is pretty simple and the finished article does a good job over and over. I hope I dont confuse you to much. www.segmentedturning.co.uk

 

12 Steps to Segmented Turning Excellence: Step 10 - Aligning the Joints ·
By: William Kandler
November 30, 2012 · 3,781 views

Vertical joint alignment is very important to the overall visual effect. Always mark the center of your segments to make alignment with the prior rings easier. When possible, keep the trimmed diameter joints aligned vertically so that all the error caused by trimming is localized. This will make the rest of the joints look better and the slight un-evenness at these joints will likely go un-noticed.

 

12 Steps to Segmented Turning Excellence: Step 12 - Preventing Vibration ·
By: William Kandler
November 29, 2012 · 3,765 views

While stacking and turning the inside of the project, it will start to sing in the upper layers because of the thin-ness of the walls. So, don't do any turning of the outside of the project until it's completely stacked. But if the singing gets too annoying, turn the outside of a couple rings to accommodate a steady rest. If you've frugally sized your rings (no excess material) then turning the outside of the project becomes a 'connect the dots and smooth' affair. If you aren't frugal, then a bit of measuring will be needed to achieve the planned form.

 

12 Steps to Segmented Turning Excellence: Step 8 - The Ring Halves Become One ·
By: William Kandler
November 14, 2012 · 3,983 views

Use a flat sanding surface to true up the ring halves for a perfect final joint. I'm using a 10' flat disk from Woodcraft with a 120 grit disk. Mark where the trimmed halves are jointed for later reference, apply glue, apply clamp (tight!), and clamp from top and bottom at the two joints to maintain a flat ring. A flat ring requires less removal of materal when flattening the ring prior to gluing. I forgot the first item before gluing; later I corrected my omission.

 

12 Steps to Segmented Turning Excellence: Step 7 - Gluing Segments into Rings ·
By: William Kandler
November 13, 2012 · 6,969 views

Glue each ring together, as two halves in a single step process, with a thin spacer at the two diameter points. Cheap coffee stir sticks work well. Clamp top and bottom against cauls to make the ring flat and around with heavy duty stainless steel band clamps turned as tight as possible. The tight clamp, forget about glue starved joints, ensures minimum width glue joints and maximizes the probability of getting a true circle, even after truing up the diameter faces. Using the cauls means you will need to remove a minimum of material to flatten the rings. If you're in a hurry, a mere 45 minutes in the clamps and the rings will be ready for the next step.

 

12 Steps to Segmented Turning Excellence: Step 6 - Cutting Segments ·
By: William Kandler
November 12, 2012 · 12,933 views

When cutting segments, the miter angle needs to be as close to perfect as possible to make rings that are true circles. Cut complete sample rings out of cheap wood and bind in a rubber band to check for gaps and tune as needed. For all angular cuts, you need to be sure the piece cannot move in the middle of the cut so that the newly cut face is perfectly flat.

 

12 Steps to Segmented Turning Excellence: Step 5 - Table Saw Setup ·
By: William Kandler
November 10, 2012 · 4,655 views

In this step, I talk about setting up your table saw so you can get true cuts. Your stock must have vertical sides and a flat, level top. Otherwise, you're making trouble for yourself in making true circles and flat rings. If you are making sandwiches or multi-generation designs, this becomes even more important.

 

Introduction to A pattern ring used in segmented turning ·
By: Segmentedturning
November 08, 2012 · 51,432 views

Here I show how to make a simple diamond shape pattern ring for using in a bowl. this is just about the easiest pattern ring there is to make but provides the basics for more complex patterns as in the title screen for this video. http://www.segmentedturning.co.uk

 

12 Steps to Segmented Turning Excellence: Step 9 - Flattening a Ring ·
By: William Kandler
November 08, 2012 · 5,742 views

At least one face of each ring must be flattened prior to gluing to the project. You can do this with a drum sander or on the lathe. For smaller rings (less than 6' diameter) the drum sander is a bad choice. For lathe flattening, simply affix an MDF circle to a faceplate, flatten as needed, and mark concentric circles on the MDF surface. Then attach each ring to the MDF/faceplate using double-sided tape and use your circles to get it centered. Then just a couple minutes with a scraper and a flat sanding board will result in a perfectly flat side.

 

12 Steps to Segmented Turning Excellence: Step 11 - Stacking & Internal Turning ·
By: William Kandler
November 07, 2012 · 5,533 views

Glue just one or two rings onto the project at one time to minimize how much the chisel needs to hang out beyond the tool rest. This will make the whole turning job easier and safer. This also prevents accumulation of off-center gluing error because you are going back zero with each ring. Use a tail stock mounted 45 degree cone to center each ring as it is glued on to get the best centering possible. Failing this, turn the last ring until round, then dry fit and measure around the ring repeatedly to place the next ring properly and hot-glue blocks to hold ring in place during gluing and clamping. The blocks will turn away easily, or just knock them off after the glue has dried. Turn the inside of each added ring, using the inside diameter of the next ring as a reference, and fare into the previous layers and sand. By the time you reach the top of the project, the bottom is long since done.

 

Sloping veneer in a segment face part 7 ·
By: Segmentedturning
October 08, 2012 · 707 views

part 7 of sloping veneer in this video finish up the bowl http://www.segmentedturning.co.uk

 

Sloping veneer in a segment face part 6 ·
By: Segmentedturning
October 08, 2012 · 365 views

part 6 of sloping veneer in this video we have the bowl on the lathe and start to turn it. http://www.segmentedturning.co.uk

 

Sloping veneer in a segment face part 5 ·
By: Segmentedturning
October 08, 2012 · 462 views

part 5 of sloping veneer in this video we have the bowl on the lathe and start to turn it. http://www.segmentedturning.co.uk

 

Sloping veneer in a segment face part 4 ·
By: Segmentedturning
October 08, 2012 · 420 views

part 4 of sloping veneer in this video we make the base that will go on the bottom of the bowl. http://www.segmentedturning.co.uk

 

Sloping veneer in a segment face part 3 ·
By: Segmentedturning
October 08, 2012 · 462 views

part 3 of sloping veneer in this video we sand and cut the segments. http://www.segmentedturning.co.uk

 

Sanding a segmented ring on a belt sander ·
By: Segmentedturning
October 08, 2012 · 757 views

This video shows how to sand a ring using the belt sander

 

sloping veneer in a segment face part 2 ·
By: Segmentedturning
October 04, 2012 · 630 views

redubbed version to get rid of radio. A demonstartion of how to make a segment with a sloping veneer in the face and also demonstrtaes how to glue up segments that have a corner to corner cut http://www.segmentedturning.co.uk

 

sloping veneer in a segment face part 1 ·
By: Segmentedturning
October 04, 2012 · 844 views

re dubbed version to get rid of radio. A demonstration of how to make a segment with a sloping veneer in the face and also demonstrates how to glue up segments that have a corner to corner cut. http://www.segmentedturning.co.uk/index.html

 

segmented ring glue up ·
By: Segmentedturning
October 01, 2012 · 1,764 views

Glueing up a segmented ring using polyurethene glue. See my work at http://www.segmentedturning.co.uk

 

Followup to Gluing Insert on an Angle video ·
By: SegmentedTurner
August 10, 2012 · 3,211 views

This shows how the final piece looks. This is one of my tools that I make.

 

Missing Segments ·
By: Dennis Edwards
August 08, 2012 · 36,189 views

Another boring segmented bowl movie

 

Segmented goblets ·
By: JGwoodshop
May 01, 2012 · 2,180 views

How to make a segmented goblet on the lathe. Really easy project and the contrasting woods look real nice after two coats of polyurethane and natural bees wax.

 

Segmented Turning Vol 7 Promo ·
By: Malcolm Tibbetts
April 16, 2012 · 8,799 views

This is a short description of my latest instructional DVD Segmented Jewelry. http://www.tahoeturner.com/book-dvd.html

 

Segment turning.wmv ·
By: Gary Jones
December 15, 2011 · 627 views

 

Arte en Torno - Torneado Segmentado ·
By: Arte en Torno
November 04, 2011 · 11,830 views

En este video mi profesor Cesar explica a los aprendices algunos procesos de como se tornea la parte superior de un jarrón o florero armado mediante la técnica del torneado segmentado.

 

Waste block drilling update ·
By: SegmentedTurner
October 15, 2011 · 1,736 views

While drilling the small alignment hole in the spindle waste block the drill may wander. Here I present one solution to that issue.

 

Glue press ·
By: Bob Hamilton
October 14, 2011 · 16,881 views

This video is in response to requests I have received for more information about the glue press I use for clamping segmented bowl assemblies.

 

Making a Turbine Design Segmented Turning - The Turning ·
By: SegmentedTurner
September 15, 2011 · 10,469 views

This is part 2 of a two part video showing the construction and turning of a special design segmented bowl.

 

stictched vessel- part two ·
By: Dan Walker
August 06, 2011 · 845 views

stictched vessel- part two

 

Segmented wood turning ·
By: TheWood2saw
May 17, 2011 · 2,781 views

Segmented wood turning on delta lathe

 

08-07-10 (Part 4 of 4) Segmented Turning by Don Russell ·
By: Gwinnett Woodworkers
May 08, 2011 · 8,266 views

In this second demonstration (a continuation of the Geometric Segmentation class), Don Russell discusses lathe turning segmented blocks to produce finials, bowls and other turned items. Part 4 of 4 parts. Filmed and uploaded in HD Original Class Date 08-07-10.

 

08-07-10 (Part 3 of 4) Segmented Turning by Don Russell ·
By: Gwinnett Woodworkers
May 06, 2011 · 14,157 views

In this second demonstration (a continuation of the Geometric Segmentation class), Don Russell discusses lathe turning segmented blocks to produce finials, bowls and other turned items. Part 3 of 4 parts. Filmed and uploaded in HD Original Class Date 08-07-10.

 

08-07-10 (Part 2 of 4) Segmented Turning by Don Russell ·
By: Gwinnett Woodworkers
May 05, 2011 · 315,471 views

In this second demonstration (a continuation of the Geometric Segmentation class), Don Russell discusses lathe turning segmented blocks to produce finials, bowls and other turned items. Part 2 of 4 parts. Original Class Date 08-07-10 Filmed and uploaded in HD.

 

08-07-10 (Part 1 of 4) Segmented Turning by Don Russell ·
By: Gwinnett Woodworkers
May 04, 2011 · 15,449 views

In this second demonstration (a continuation of the Geometric Segmentation class), Don Russell discusses lathe turning segmented blocks to produce finials, bowls and other turned items. Part 1 of 4 parts. Original Class Date 08-07-10 Filmed and uploaded in HD.

 

08-07-10 (Part 6 of 6) Geometric Segmentation by Don Russell ·
By: Gwinnett Woodworkers
April 01, 2011 · 28,272 views

Don Russell discusses using geometric shapes to produce multi-part wood patterns in flat objects using repeated motifs for inlays - this process can be repeated to create segmented blocks for turning bowls and other turned objects. Part 6 of 6 parts. Filmed and uploaded in HD. Original Class Date 08-07-10.

 

08-07-10 (Part 5 of 6) Geometric Segmentation by Don Russell ·
By: Gwinnett Woodworkers
March 31, 2011 · 9,231 views

Don Russell discusses using geometric shapes to produce multi-part wood patterns in flat objects using repeated motifs for inlays - this process can be repeated to create segmented blocks for turning bowls and other turned objects. Original Class Date 08-07-10 Part 5 of 6 parts. Filmed and uploaded in HD.

 

08-07-10 (Part 4 of 6) Geometric Segmentation by Don Russell ·
By: Gwinnett Woodworkers
March 31, 2011 · 10,611 views

Don Russell discusses using geometric shapes to produce multi-part wood patterns in flat objects using repeated motifs for inlays - this process can be repeated to create segmented blocks for turning bowls and other turned objects. Part 4 of 6 parts. Original Class Date 08-07-10 Filmed and uploaded in HD.

 

08-07-10 (Part 3 of 6) Geometric Segmentation by Don Russell ·
By: Gwinnett Woodworkers
March 27, 2011 · 23,412 views

Don Russell discusses using geometric shapes to produce multi-part wood patterns in flat objects using repeated motifs for inlays - this process can be repeated to create segmented blocks for turning bowls and other turned objects. Part 3 of 6 parts. Original Class Date 08-07-10 Filmed and uploaded in HD.

 

08-07-10 (Part 2 of 6) Geometric Segmentation by Don Russell ·
By: Gwinnett Woodworkers
March 27, 2011 · 14,252 views

Don Russell discusses using geometric shapes to produce multi-part wood patterns in flat objects using repeated motifs for inlays - this process can be repeated to create segmented blocks for turning bowls and other turned objects. Part 2 of 6 parts. Original Class Date 08-07-10 Filmed and uploaded in HD.

 

08-07-10 (Part 1 of 6) Geometric Segmentation by Don Russell ·
By: Gwinnett Woodworkers
March 27, 2011 · 17,043 views

Don Russell discusses using geometric shapes to produce multi-part wood patterns in flat objects using repeated motifs for inlays - this process can be repeated to create segmented blocks for turning bowls and other woodturned objects. Part 1 of 6 parts. Original Class Date 08-07-10 Filmed and uploaded in HD.

 

Easy Method of Glueing Segments into a Ring for a Segmented ·
By: KochUSA
January 28, 2011 · 49,721 views

Created on January 28, 2011 using FlipShare.

 

2010 Segmented Symposium ·
By: Dick Fuller
November 25, 2010 · 52,010 views

2010 Annual Segmented Symposium at Arrowmont School of Arts in Gatlinburg Tn.

 

Holzhut Drechseln Woodturning ·
By: Hanspeter Schneider
July 15, 2010 · 16,086 views

Drechseln eines Holzhutes www.atelier-schneider.ch

 

the finish.wmv(PT.12) ·
By: thesegmenter
March 30, 2010 · 5,346 views

part twelve of building a segmented bowl. come join us at http://www.woodturnersresource.com/ to see this bowl in high quality as well as to check out http://www.woodturnersresource.com/wrphotopost/showgallery.php?cat 500&ppuser 4133 and to look at Malcolm Tibbett's amazing site click here http://tahoeturner.com

 

stacking the rings.wmv(PT.11) ·
By: thesegmenter
March 30, 2010 · 9,142 views

part eleven of our building a segmented bowl.

 

fixing segments.wmv(PT.10) ·
By: thesegmenter
March 26, 2010 · 12,825 views

part ten of building a segmented bowl, this video is basically a stand alone video, but i feel it is an important technique you should know about.

 

glueing the segments.wmv(PT.8) ·
By: thesegmenter
March 19, 2010 · 8,683 views

part eight of building a segmented bowl

 

cutting our segments.wmv(PT.7) ·
By: thesegmenter
March 19, 2010 · 15,022 views

part seven of our segmented bowl

 

Introduction to Segmented Turning with Curt Theobald (woodturning DVD preview) ·
By: Craft Supplies USA
March 17, 2010 · 20,316 views

A preview of Curt Theobald's woodturning video 'Introduction to Segmented Turning'. Buy now: https://www.woodturnerscatalog.com/p/70/2039/Curt-Theobald-Intro-to-Segmented-Turning-DVD?utm_source youtube&utm_medium description&utm_campaign videos Please subscribe to our channel: https://www.youtube.com/user/CraftSuppliesUSA This video takes you step-by-step through creating precise jigs and producing accurate glue joints in segmented woodturnings. The many tips and methods covered in this video are useful to segmented turners of all skill levels. 85 minutes. Craft Supplies USA (The Woodturne

 

Segmented Patterns with Curt Theobald (woodturning DVD preview) ·
By: Craft Supplies USA
March 17, 2010 · 11,575 views

A preview of Curt Theobald's woodturning video 'Segmented Patterns'. Buy now: https://www.woodturnerscatalog.com/p/70/3249/Curt-Theobald-Segmented-Patterns-DVD?utm_source youtube&utm_medium description&utm_campaign videos Please subscribe to our channel: https://www.youtube.com/user/CraftSuppliesUSA From a blueprint to the finished bowl, Curt clearly explains and demonstrates the various types of segmented turnings in an easy to follow format. Curt's helpful tips and insights take the mystery out of the process of segmented bowl construction. This video is a good reference for turners of all

 

intro to segmented turning.wmv(PT.1) ·
By: thesegmenter
March 06, 2010 · 15,273 views

this is part one of a multipart series on the process i use to create my segmented bowls. please stay tuned as new parts will be added shortly.

 

Segmented turning planner ·
By: Cap'n Eddie Castelin
October 12, 2009 · 14,601 views

A plastic laminated segmented planner with 9 different angle layouts. from 4 to 24 segment rings can be laid out on the planner. Order online at ww.eddiecastelin.com, use Pay Pal for Payment

 

Using my tools turning red oak ·
By: SegmentedTurner
August 11, 2009 · 41,919 views

I show the use of both my standard and micro turning tools on 12 inch diameter red oak. I'm making column bases for a vintage Detroit house and I'm using my tools for this job. In this video I show heavy turning capabilities and some detail work. For more information about my work please visit my web site at http://www.DWMontville.com.

 

Segmented Woodturning Event ·
By: Malcolm Tibbetts
January 07, 2009 · 14,451 views

 

Segmented Woodturning Lessons ·
By: Malcolm Tibbetts
November 05, 2008 · 37,604 views

A brief sample of video lessons.

 

Seggy's Dream - a Woodturning Story ·
By: Malcolm Tibbetts
December 05, 2007 · 57,697 views

This is a story of hope and persistence, along with being a 'how to' on segmented woodturning. It's also an attempt to raise money for the American Cancer Society. Be sure to view the very end. Thanks

 

Return to Turning Videos

Great Bargains


Heavy Duty Live Center

On Sale for only $16.53

List Price: $19.95

Click here for more information or to purchase

 


Dremel Rotary Tool Kit

On Sale for only $139.00

Save $60.99 (30%)

List price: $199.99

Click here for more information or to purchase


Roller Stand

On Sale for only $23.79

Save $6.11 (20%)

List Price: $29.90

Click here for more information or to purchase

 


Easy Wood Tools - Easy Start Rougher + Finisher + Detailer

On Sale for only $159.99

List price: $206.97

These tools have the smaller 9" maple handle and are 12.5" overall.

Click here for more information or to purchase


NOVA 48232 G3 Reversible Wood Turning Chuck

On Sale for only $99.00

Save $60.99 (38%)

List price: $159.99

Click here for more information or to purchase

Powered by Google

Our Newsletter

We update our home page about monthly to feature a new project, a new article, and a new and hot tool. Then we create a newsletter to alert our subscribers.
We never let anyone use our list, and our subscribers have been wonderfully loyal as a result.

We hope you will try it out!

Sign Up For Our Newsletter

A Sampling of our Sponsors:
(Visit the Vendor's Corner above to see all our sponsors)

Saburrtooth
Woodturning with Tim
From Walnut to Antlers

(Click any Ad to go to our Sponsor's Website)