Woodturning Online Videos


Welcome to the Woodturning Online Videos page.

This video content was created by woodturner, Rick Morris. He has created a way to monitor all the videos in YouTube that are woodturning related.

Each month, Rick updates the video listings below. If you would like to learn about new videos, sign up for our free newsletter where we will list the top 20 videos each month.

Any categories in BOLD have sub-categories to help you narrow down your search.

Steady Rests or Tool Rests Videos (84)

Sort by

Or click here to: Search All Videos


Double 9 D ·
By: J.B Wood Turning
November 15, 2017 · 38 views

The Double 9 D wood lathe tool rest is a reach beyond the status quo. Available at: http://jbwoodturn.com

 

A New Tool Rest Under the Sun!! ·
By: RickTurns
November 08, 2017 · 2,669 views

The Double 9 D is a new style of tool rest...a single rod of 1' steel stamped into a shape with two 90 degree bends. I test it out on bowls and spindles. Link to Double 9 D video by the inventor: http://bit.ly/2hU5eNz Link to purchase the Double 9 D: http://etsy.me/2zu2bW3 The music during the close of the video, Happy Little Elves by Audionautix, is licensed under a Creative Commons Attribution license (https://creativecommons.org/licenses/by/4.0/) Artist: http://audionautix.com

 

Double 9 D ·
By: J.B Wood Turning
October 26, 2017 · 354 views

A new 'beyond the status quo' wood lathe tool rest. Designed by a wood turner for wood turners. Joe Glassford has created the Double 9 D tool rest as a result of being frustrated with the tool rests that were on the market. This tool rest has taken Joe's turning to a new level. It could do the same for you. Thanks for watching.

 

36 - Fabricating Some Tool Rests ·
By: Bill Rockwood
August 24, 2017 · 522 views

I fabricate some tool rests for hollowing from basic steel stock, two of which are captive rests, for use with my longer carbide hollowing tool.

 

Adjusting The Tool Rest - Part 3 (conclusion) ·
By: Ron Calverley
July 23, 2017 · 468 views

Adjusting the height of my small tool-rest so that it will fit my lathe.

 

Adjusting The Tool Rest - Part 2 ·
By: Ron Calverley
July 22, 2017 · 540 views

Adjusting the height of my small tool-rest so that it will fit my lathe.

 

Adjusting The Tool Rest - Part 1 ·
By: Ron Calverley
July 21, 2017 · 485 views

Adjusting the height of my small tool-rest so that it will fit my lathe.

 

002-1 WWRJF A simple Steadyrest 7min ·
By: Richard Ford
June 21, 2017 · 32 views

This is the Simple Steady-rest I used in my 2011 method of drilling tool handles. It can be used for supporting long spindle turnings that are not to large. Originally Uploaded on Feb 23, 2011. Re-Posted Jun 21, 2017

 

SETTING UP & USING THE ROBO REST by Reed Gray aka Robo Hippy ·
By: robohippy
May 31, 2017 · 2,721 views

2017 Robo Hippy shares new and improved insights to help you set up and use your Robo Rest safely and securely.

 

MesquiteHollow ·
By: The Spin Doctor - TSDr, LLC
April 17, 2017 · 225 views

Clark Deep Hollowing System and Clark Steady Rest demonstration hollowing a 33 inch mesquite burl over 20 inches deep.

 

New Tool Rest # 78 ·
By: The Wood Whirler
April 05, 2017 · 1,705 views

I needed a different style tool rest. Contact is at earthloc@gmail.com

 

steady rest that works on open segments ·
By: earl's small segment shop
March 31, 2017 · 1,405 views

A steady rest that will work for open segment turnings

 

#183 Steady rest ·
By: Miguel Sanchez
March 08, 2017 · 3,359 views

Este video tambien esta en Español sigue el enlace mas abajo. This video is also in English, click the link below. https://www.youtube.com/channel/UCyOE_zdEBv4UcK5a_a3Z6hA Miguel Sanchez 2: https://www.youtube.com/channel/UC2JiORNXY4uz2wg3hL1oLHA Ayuda al canal desde 1 dolar al mes: Help de channel from as little as 1 dollar per month http://www.patreon.com/miguelsanchez http://www.tornoartesano.es mailto:miguel@tornoartesano.es

 

Pencil Epoxy Clock # 68 ·
By: The Wood Whirler
February 12, 2017 · 8,836 views

My first pencil project.

 

Clark Steady Rest in Action ·
By: The Spin Doctor - TSDr, LLC
December 26, 2016 · 317 views

I created this video with the YouTube Video Editor (http://www.youtube.com/editor)

 

My Heath Robinson steady ·
By: woodturner21
November 29, 2016 · 1,902 views

A quick video showing my Heath Robinson steady

 

The New Nova Modular Tool Rest System ·
By: RickTurns
October 24, 2016 · 3,397 views

A review of Teknatool's new Nova modular tool rest system.

 

TriSpin steady rest features and demonstration ·
By: WoodTurningUK
October 24, 2016 · 146 views

A demonstration of the solid oak TriSpin Steady rest for purchase from www.kengarner.co.uk Thank you for watching.

 

A more Steady, Steady Rest ·
By: Rich McNatt
October 03, 2016 · 2,644 views

 

capture 11 August 2016 07 39 55 PM ·
By: Show Me Woodturners
August 26, 2016 · 64 views

Thin Turning Using A String Steady with Craig Schmidt

 

Steady rest ·
By: mark's creative turnings
August 24, 2016 · 148 views

 

Tool Rest Fix # 42 ·
By: The Wood Whirler
August 17, 2016 · 2,885 views

All my tool rests for the old Harbor Freight lathe were too short for my new Grizzly G0800, so I had to fix them. This video shows how I did it.

 

The Catch That Broke The Tool Rest ·
By: Paul Lockwood
July 30, 2016 · 859 views

By the looks of this a double catch that threw the skew into the chuck and then forced it down onto the tool rest snapping it off.

 

Bad Workshop Day - Episode 16 ·
By: Paul Lockwood
July 30, 2016 · 514 views

A bad day in the Workshop. I really wasn't in the correct frame of mind but wanted to get on with something on the lathe. First up deicded to turn a small snowman to practice turing the curves. After that went to try and do a spinning top which is where things went wrong. A catch which threw the skew into the chuck and forced it down to snap the tool rest. Also a preview of an upcoming project which invloves making a housing for some electronics I've put togetheer. Music Pompei, Swimming In Turpentine and Mitionless Land By Josh Woodward http://freemusicarchive.org/music/Josh_Woodward/ From The Free Music Archive http://freemusicarchive.org CC Attribution 4.0 International https://creativecommons.org/licenses/by/4.0/legalcode Please Subscribe http://www.youtube.com/channel/UCJmcpalJi_xzP_iV3uXJj2w?sub_confirmation 1

 

Outboard Turning Tool Rest ·
By: Make Crazydays
July 13, 2016 · 2,794 views

Elizabeth has a new challenge with her turning club to turn a shallow bowl. What she plans on doing requires doing some outboard turning so I put together this tool rest for her. My first attempts was just bolting some angle iron to some roller stands, but that was just not stable enough. After some googling I found Sam Angelo's (WYOMINGWOODTURNER) cement and galvanized pipe tool rest and was inspired to created this rest. Sam Angelo's Channel: https://www.youtube.com/user/WYOMINGWOODTURNER All Scripture is breathed out by God and profitable for teaching, for reproof, for correction, and

 

Building a Large Tool Rest # 37 ·
By: The Wood Whirler
July 08, 2016 · 1,266 views

I decided to build a tool rest so I could reach the bottoms of a large bowls. It is stainless steel with a surprise add on at the end of the video. .

 

Steady rest test ·
By: Rebel Turner
May 12, 2016 · 1,991 views

Newest turning test for the steady rest

 

Make an easy locking cam ·
By: Rebel Turner
May 07, 2016 · 6,737 views

Just finished building this Shop made steady rest with locking cam. The difference here is I made a cam for easy lock and steel arms I just need to make handles for the lock screws that lock the arms in position. The cam works like a charm and easy to get it on the bed way The idea behind this was not to have to use any tools to put it on the lathe . lock it down or make any adjustments. I have been thinking about this froe a while and thinking how I could make it work. I think this is a great design for those who want something with a little twist. Wood turning tutorials as well as tool modifications

 

Wood turning tool rest tool height ·
By: Rock Springs Woodturner
April 11, 2016 · 6,066 views

Discussion and demonstration of setting tool rest height and distance from work for spindle turning safety, efficiency, and consistency.

 

Shop Built, Floor-Mount Tool rest: (video Remake) Sam Angelo woodturning ·
By: WYOMINGWOODTURNER
April 07, 2016 · 6,007 views

Sam shows what it takes to make this simple 'floor-mount' tool rest. This accessory is necessary for turning very large diameter pieces. By moving the headstock forward on his Powermatic he has almost unlimited access to turning large pieces. Sam focuses on chasing threads in galvanized pipe. Necessary for completing the tool rest.

 

Wood Turning - RoboRest review ·
By: Mike Waldt
April 02, 2016 · 7,551 views

I review the RoboRest by Reed Gray aka RoboHippy. RoboHippy's Channel - https://www.youtube.com/user/robohippy Robohippy's Website - http://www.robohippy.net/ UKIWS - https://www.ukiws.co.uk

 

Homemade Wood lathe - Articulated tool rest ·
By: Ray MAKES
March 03, 2016 · 2,603 views

This is my finished articulated tool rest.... i just need to paint it to match (lets see how long that takes)! the original version had the 2nd link arm too long and it flexed terribly. the shorter 2nd link is much stiffer, and now the lathe is perfect. to view the complete video of my homemade lathe specifications please visit this link https://youtu.be/11Dh0XLtdFQ

 

Steady rest diy ·
By: yak branson
March 02, 2016 · 241 views

Video for a friend al, he asked if i had my steady rest done and replyed with this video so he could see my ugly but useful steady rest.

 

Woodshop Tour 07 DIY Steady Rest & Longworth Chuck ·
By: Dipa Das
February 18, 2016 · 9,020 views

How to build Steady Rest & Longworth chuck for less than 15E? :-)

 

UKIWS Update & Tool Rest Questions Answered ·
By: Mike Waldt
February 15, 2016 · 5,465 views

A short Update on UKIWS progress, and more exciting news. Also some common Tool Rest questions I get asked - answered. UKIWS Website - http://www.ukiws.co.uk/ Martins Update video - https://www.youtube.com/watch?v 4zZTGIfsYLk UKIWS Facebook page - https://www.facebook.com/ukiws

 

How to Make a Lathe Steady Rest for CHEAP ·
By: Regan Leatch
January 21, 2016 · 569 views

How to Make a Lathe Steady Rest for CHEAP. Get the cutting template here: https://www.dropbox.com/s/om13mxsesvzgsig/How%20to%20make%20a%20lathe%20steady%20rest%20for%20cheap.pdf?dl 0 Check out more of the stuff I make Here: https://www.facebook.com/reganswoodworkingandwoodturning/ ____________________________________________________________________ Music: Alan Walker - Fade [NCS Release] https://www.youtube.com/watch?v bM7SZ5SBzyY Find the Artist Alan Walker here Facebook https://www.facebook.com/DJWalkzz SoundCloud https://soundcloud.com/walkzz Twitter https://twitter.com/IAmAlanWalker YouTube https://www.youtube.com/user/DjWalkzz ____________________________________________________________________

 

122 Home-made Lathe for less than $150 Part 2 tool rest and tail-stock ·
By: Roger Webb
January 19, 2016 · 45,335 views

Australian technology Inventor Roger Clyde Webb demonstrates How to make your own wood lathe for less than 150. Home-made lathe Part 2 tool rest and tail-stock (completion). Disclaimer: These videos are intended for entertainment and inspiration. Woodworking and metalworking is dangerous. Always seek professional advice and training before using any power tools or CNC machine. If you have any uncertainty before performing any DIY procedure, stop and learn a safer method. Understand that there are years of learning and experimentation by me that are not in the videos. Do not attempt anything simply because you saw it in one of my videos.

 

Wood Turning - Spindle Steady Rest build. ·
By: Mike Waldt
January 03, 2016 · 53,518 views

I build a steady rest that was inspired by a video from Stephen Ogle. I have a link below for the in depth step by step build that Stephen did. Stephen's Video - https://www.youtube.com/watch?v -YzyEq77Rt8

 

DIY Welded Toolrest for Wood Mini-Lathe ·
By: Barry's Workshop
December 13, 2015 · 1,772 views

I got tired of the limits of the toolrest that came with my mini lathe so I welded a larger one using some scrap hot rolled angle and steel rod that I had left over from other projects. It's only a few inches wider (8.5' [22cm] vs. 6' [15cm]), but it makes a big difference in being able to turn larger work. I also didn't want to make it too big because my lathe's banjo only has 5/8' [16mm] shaft. Music by audionautix.com. Released under Creative Commons License 3.0.

 

Make a Stop Collar For Your Tool Rest ·
By: RickTurns
December 12, 2015 · 2,499 views

It's easy to make a stop collar for your tool rest post. Very few materials are required and it's fairly quick to turn. A stop collar slides on the post of the tool rest, and can be tightened at any position, allowing the tool rest to be removed and then put back at exactly the same height. Here are links to some of the commercially-available stop collars for tool posts: Rubber Chucky Tool Rest Height Adjust (Step Chucky) http://bit.ly/1Uj9KjS Turners Select Center-Set Post Lock http://bit.ly/1NWrOuM Nova Tool Rest Collar http://bit.ly/1Ma5mwW

 

Le PicBois - Fail #2 : I think I need a new tool rest! ·
By: Le PicBois
September 27, 2015 · 2,723 views

[ Yeah! I need one strong enough for my teeth! ] Support me on Patreon: https://www.patreon.com/lepicbois Website: http://lepicbois.net/ YouTube: https://www.youtube.com/lepicbois Facebook: https://www.facebook.com/AtelierLePicBois Instagram: http://instagram.com/atelierlepicbois Twitter: https://twitter.com/atelierpicbois - - - - - - Please watch: 'Le PicBois #17 - Beer Glass' https://www.youtube.com/watch?v SOTVj8aPruY - - - - - -

 

Tool Rests for Woodturners ·
By: Mike Peace Woodturning
August 16, 2015 · 8,199 views

I explain the ins and outs of tool rests for wood lathes. I review how to safely use one, how to maintain it, why you might want to consider adding another one to your tools, and what are some the considerations in your choice to make or buy one. Check out my blog for demonstration handouts, downloadable copies of articles I have published, and links to some full length demonstrations I have done at Gwinnett Woodworkers channel. MikePeaceWoodturning.blogspot.com

 

String Steady Rest #2 ·
By: Gord Rock
July 23, 2015 · 1,587 views

How to put together a string steady rest that will allow a turner to support a spindle. Link to my other string steady rest: https://youtu.be/oMdSXeKYZcE Link to wheeled steady rest: https://youtu.be/P0CJF-lMe3E

 

#34 NO Steady Rest Djembe Tutorial ·
By: Uncle Cys Woodshop
July 16, 2015 · 1,793 views

A two piece Djembe that can be done without a Steady rest and with normal tools. I do still recommend getting an end grain hollowing tool of some sort ring tool or hook tool. You can find hand made hook tools from Steven https://www.youtube.com/watch?v DgGJvibZdHQ And Harry shows how he makes them https://www.youtube.com/watch?v qodsXio8rm4

 

#33 Walnut Djembe And Steady rest Improvements ·
By: Uncle Cys Woodshop
July 13, 2015 · 65,848 views

I decided to slow the Time Lapse rate down and let you see a bit more detail of the process. I also had to make some improvements to my Steady Rest, i melted a wheel and found a bit more flex in it than I liked. Finding wheels in my area was a pain, luckily I found CAPPs bicycle shop in Topeka, Kansas had 1 set left (they don't carry skateboard stuff anymore) They were super nice and the shop was awesome check them out at http://www.cappsbikeshop.com/index.html

 

Make a tool rest - part 6 - Brazing ·
By: RickTurns
March 19, 2015 · 6,290 views

In this sixth and final video in my series of videos about making a tool rest (without welding!), I braze the arm to the post, and then the wear strip to the arm. After cleaning up the new tool rest, I cut and adjust the height on the lathe. The manufacturer's video on using the oxy-mapp torch is here: https://youtu.be/a38PdQkcInA Jan 23 2016 - this just in! Lyle Jamieson passed on a suggestion to put a wedge of wood in the right angle of the angle iron, so that if the tool slips off the end (or even the lip) of the rest, you'll be less likely of catching a finger or two. Sounds like a good idea to me.

 

Part 3 of 3 Setting Up and useing the SR 20 Steady Rest ·
By: Paul Crabtree
March 12, 2015 · 339 views

This very important segment explains how to finish out a vase, ready for sanding after it finished drying.

 

Make a tool rest - part 5 - Cutting ·
By: RickTurns
March 10, 2015 · 3,498 views

In the fifth video of my series on how to make a tool rest for your woodturning lathe (without welding!), I show how to cut the metal pieces for the tool rest, how to square off the top of the post, how to tap the hole in the top of the post, and where to drill the arm.

 

Wood Turning: Shop Made Captive Tool Rest ·
By: Stephen Zamecnik
March 05, 2015 · 1,743 views

In this video I will walk you through my homemade captive tool rest, for hollow turning. A very simple design at an extremely reasonable cost. The rest is still in a fairly raw state so don't be to hard on me. If you have any questions or comments please feel free to chime in, i would love to hear your two cents.

 

Make a tool rest - part 4 - Sizing ·
By: RickTurns
March 04, 2015 · 6,180 views

In the fourth video of my series on how to make a tool rest for your woodturning lathe (without welding!), I describe how to determine the best height for the tool rest post.

 

Make a tool rest - part 3 - Materials ·
By: RickTurns
February 28, 2015 · 6,855 views

In the third video of my series on how to make a tool rest for your woodturning lathe (without welding!), I describe the materials (primarily steel) needed to make the toolrest, including the average costs and several online sources. As mentioned in the video, here are URLs for various sources of steel and silver braze: Online Metals (metals) http://bit.ly/1E5nQAr Metals Depot (metals) http://bit.ly/1Ao3kDx Speedy Metals (metals) http://bit.ly/1zOizqj Enco (metals) http://bitly.com/1DmE8iT MSC (metals) http://bitly.com/1BqQF8h Airgas (for silver braze) http://bitly.com/189BEMa

 

Make a tool rest - part 2 - Tools ·
By: RickTurns
February 27, 2015 · 7,933 views

In the second video of my series on how to make a tool rest for your woodturning lathe (without welding!), I describe the different tools you'll need to do the work, including the most likely costs and several online sources. Here are some links for tool sources: For the Oxy-MAPP torch kit http://bit.ly/1AR99gt http://bit.ly/1E3ImRX http://bit.ly/1DZdbFO For the 4 1/2 inch angle grinder http://amzn.to/1EU9hwq http://thd.co/1MYhc1c For the tap-drill combo http://amzn.to/1BGNk6O http://thd.co/1wupGs4 For silver brazing material http://bit.ly/1BGMWp0 http://bit.ly/17Dgx4O

 

Make a tool rest - part 1 - overview ·
By: RickTurns
February 25, 2015 · 27,120 views

Woodturning: Make a tool rest of any length for your woodturning lathe, using silver brazing. No welding required! Jan 23 2016 - this just in! Lyle Jamieson passed on a suggestion to put a wedge of wood in the right angle of the angle iron, so that if the tool slips off the end (or even the lip) of the rest, you'll be less likely of catching a finger or two. Sounds like a good idea to me.

 

Update To My DIY Lathe Steady Rest ·
By: As Wood Turns
September 04, 2014 · 6,544 views

http://www.AsWoodTurns.com I've been using my home made steady rest for over a year. During this time, I've thought of a couple of improvements: 1) Use locknuts in place of the nuts. Vibration in use caused nuts to come loose and fall off. 2) Replace the base that mounts it to the lathe so that I can place the tool rest closer to the project and the steady rest. Other than the nuts, replacing the base was the easy part. I still needed the steady to be adjustable so the key upgrade was a coupling assembly. This assembly enables the steady upright to be attached to the base but enables adjustmen

 

Lathe tool rest and countershaft built ·
By: Rebel Turner
August 17, 2014 · 1,158 views

I have built a lathe tool rest and a countershaft to go with my lathe riser blocks

 

Making A String Steady Rest For Woodturning ·
By: Gord Rock
August 10, 2014 · 77,048 views

Showing how to make a String Steady Rest that I use when turning a finial.

 

Building A Steady Rest For Woodturning ·
By: Gord Rock
August 04, 2014 · 10,364 views

How to build a steady rest for your wood lathe.

 

SJWood Shorts - Tool Rest Discussion for Woodturning ·
By: SJWoodworks
July 13, 2014 · 1,616 views

This video is a brief discussion about the tool rests I have for my wood lathe and that I use for woodturning. This is the first in a now-and-then series of very short videos where I just talk about some specific tool or piece of equipment and either give a review or demonstrate it or talk about it in some way. I hope you can get something out of it! Please feel free to leave me a comment, and I will respond.

 

Woodturning: Tool Rest Height (Inside A Bowl) ·
By: Roundabout Woodworks
July 11, 2014 · 1,907 views

This answers the question 'How high should I set my tool rest for the inside of a bowl?'

 

TOOL REST HEIGHT and POSITION: Woodturning ·
By: WYOMINGWOODTURNER
April 23, 2014 · 30,969 views

Sam explores proper tool rest positions. He does sample cuts on the inside and outside of a bowl.

 

Making a new crude steady rest Part 2 ·
By: Bob Hamilton
March 09, 2014 · 6,710 views

I finally had need of a steady for the new lathe so I put together another crude steady rest sized to fit this lathe. The old one went with the DVR when I sold it. This is part two of a two part video showing the construction of the new steady.

 

Making a new crude steady rest Part 1 ·
By: Bob Hamilton
March 09, 2014 · 6,485 views

I finally had need of a steady for the new lathe so I put together another crude steady rest sized to fit this lathe. The old one went with the DVR when I sold it. This is part one of a two part video showing the construction of the new steady.

 

# 214 Tool Rest Height Standards? ·
By: Cap'n Eddie Castelin
February 12, 2014 · 42,284 views

Big Guy Productions and Capt. Eddie Castelin are at it again. Contact Cap'n Eddie at eddiecastelin@cox.net or www.eddiecastelin.com

 

Tool Rests presented by Reed Gray aka robo hippy ·
By: robohippy
January 27, 2014 · 4,105 views

 

#58 Luneta, como se usa - Steady rest set up (resubido) ·
By: Miguel Sanchez
October 27, 2013 · 25,716 views

Ayuda al canal: www.patreon.com/miguelsanchez Help the channel: www.patreon.com/miguelsanchez http://www.facebook.com/profile.php?id 1181903663 http://www.tornoartesano.es miguel@tornoartesano.es

 

#57 Luneta casera - Homemade steady rest (resubido) ·
By: Miguel Sanchez
October 27, 2013 · 43,802 views

Ayuda al canal: www.patreon.com/miguelsanchez Help the channel: www.patreon.com/miguelsanchez Finalmente algo mas largo y laborioso de lo que tenia previsto pero esta hecho, espero que os sirva de guia para fabricaros la vuestra. Saludos. http://www.facebook.com/profile.php?id 1181903663 http://www.tornoartesano.es miguel@tornoartesano.es

 

#03 How to make a Shop Built Steady Rest ·
By: Stephen Ogle
October 22, 2013 · 85,477 views

I needed a steady rest in order to turn a larger than normal (for me) vase. This is my version and uses wooden Pecan wheels.

 

My DIY Lathe Steady Rest ·
By: As Wood Turns
August 27, 2013 · 20,940 views

http://www.AsWoodTurns.com After using my new steady rest turning the travel mug, many viewer requested more information about the steady rest. So here we go. It's make from Baltic birch plywood with layers glued together as necessary for thickness. The wheels came from a pair of roller blades I purchased at a local thrift store. It works fine except I'd like to be able to more my tool rest closer when the steady is near the end of the workpiece. I think it can be much closer. But before I modify the base, I'd like your ideas. I used 1/4 inch hardware. I will be doubling the nuts to prevent them from loosening. I will appreciate all comments and suggestions for improvements. Thank you in advance. Enter your email at http://www.AsWoodTurns.com & I'll let you know when the next woodturning project video is ready.

 

Tool Rest Maintenance ·
By: woodturningwithtim1
August 04, 2013 · 6,489 views

Is your tool rest looking a little worse for wear? Tim shows you how to return it to its former glory and how to maintain that nice smooth surface.

 

Using a Robust Curved Tool Rest on a Walnut Bowl (Condensed Version) ·
By: The Woodturning Store
June 16, 2013 · 5,295 views

Condensed version of the my video on turning a large walnut bowl on a Robust American Beauty Lathe with Robust Toolrests. Shot in HD. Watch Woodturning How-To videos with Steve Fulgoni at The Woodturning Store. Steve shows woodturning tips, turning techniques, woodturning product reviews and support for Hurricane Turning Tools and Robust Lathes. Please subscribe to The Woodturning Shop and send me any comments or suggestions. Check out my website at: http://www.thewoodturningstore.com or http://www.woodturner.co. On my website you will find Hurricane Tools and Chucks, Projects Supplies and I am also an authorized dealer for Robust Lathes and tools

 

Tournage sur bois: Lunette --- Woodturnig: Steady rest ·
By: Laurent Cortot
April 05, 2013 · 9,294 views

Part 1: Fabrication d'une lunette pour mon tour a bois. Making a Steady rest for my tower wood Les essais dans la prochaine vidéo :)

 

Woodturning Q&A Bowl Gouge and Tool Rest ·
By: Carl Jacobson
March 21, 2013 · 41,775 views

In this video I talk about how the bowl gouge works and cuts. Proper tool rest height and lathe maintenance. I just got a new diamond wheel and I love it no more dust. Ways you can support the show Schedule one-on-one online classes jacobson68@yahoo.com ChefwareKits http://www.chefwarekits.com/easy-wood-tools?tracking carleasy Easy Wood Tools http://www.easywoodtools.com/ Website http://www.thewoodshop.tv/ Google https://plus.google.com/113199904565893027390#113199904565893027390/posts Facebook https://www.facebook.com/pages/The-WoodshopTV/161892940583516?ref hl Welcome to my channel, I have a new project video every Friday with wood turning tips and projects. Taking you from start to finish with a ruff piece of wood to your sanded and finished project.

 

Woodturning Q&A Tool Rest Maintenance ·
By: Carl Jacobson
March 05, 2013 · 9,642 views

In this video I talk about Maintaining your lathe tool rest. Ways you can support the show Schedule one-on-one online classes jacobson68@yahoo.com ChefwareKits http://www.chefwarekits.com/easy-wood-tools?tracking carleasy Easy Wood Tools http://www.easywoodtools.com/ Website http://www.thewoodshop.tv/ Google https://plus.google.com/113199904565893027390#113199904565893027390/posts Facebook https://www.facebook.com/pages/The-WoodshopTV/161892940583516?ref hl Welcome to my channel, I have a new project video every Friday with wood turning tips and projects. Taking you from start to finish with a ruff piece of wood to your sanded and finished project.

 

Carter MultiRest (woodturning bowl/spindle steady) ·
By: Craft Supplies USA
February 05, 2013 · 108,866 views

Gain needed support on your spindle work with the Carter MultiRest. Buy now: https://www.woodturnerscatalog.com/p/110/5748/Carter-MultiRest-Work-Support-System?utm_source youtube&utm_medium description&utm_campaign videos Please subscribe to our channel: https://www.youtube.com/user/CraftSuppliesUSA The Carter MultiRest Work Support System prevents dangerous whip and provides additional support when turning thin spindle work, hollow forms and bowls by providing a unique repositionable support system that can be custom fit to suit the work at hand. This modular support system is strong an

 

Woodturning Steady Rest ·
By: Carl Jacobson
November 15, 2012 · 70,649 views

Thank you, Steve Miller send me a Steady Rest for my lathe. Check out his Ebay site. Here's a link to some of the tools I used in this video, http://astore.amazon.com/thewood0c-20 I upload a new project video every Friday. Thank you for supporting free woodworking My Etsy shop https://www.etsy.com/shop/Thewoodshoptv Patreon, I really appreciate your support. https://www.patreon.com/CarlJacobson Schedule demos, and one-on-one online classes jacobson68@yahoo.com I'm a Robust dealer if you have any questions I'd be more than happy to help. Robust Woodturning Tool

 

Shop-built outboard Wood Lathe tool rest ·
By: WYOMINGWOODTURNER
October 28, 2012 · 32,026 views

Sam Angelo shows details of a shop-built, 'outboard' tool rest. With the headstock of his lathe moved to the front of the bed ways, Sam is able to turn pieces larger than the 20 inch swing of his lathe.

 

The M Spindle Steady Jig — Woodturning ·
By: Jake Gevorgian
October 19, 2012 · 18,280 views

Drawings are now available for download. Visit: http://www.paloarte.com/the-m-spindle-steady-jig-drawings-for-woodturners/ I took the basic concept from a gentleman named Richard who has a youtube channel, here http://youtu.be/tUwGqTyq68E After telling my father about this jig, as a structural engineer, he decided to make one for me. Thanks to my dad now I have a jig that can hold long spindles on the lathe without a tail stock. I've done several aggressive cuts on it and nothing moved, except that I pushed the jig a little back because the tool rest was vibrating and when it became loose I pushed it along with my aggressive cuts.

 

The GM5-280 Woodturning steady rest ·
By: WoodTurningUK
October 09, 2012 · 1,074 views

Here is the GM5-280 Woodturning steady rest Please visit www.kengarner.co.uk for the improved oak version. Happy Turning

 

GM5-400 Woodturning steady rest ·
By: WoodTurningUK
October 09, 2012 · 4,381 views

Hello all, this video is now legacy. Please visit www.kengarner.co.uk for the new model, the TriSpin

 

125 tool rest ·
By: Cap'n Eddie Castelin
May 08, 2012 · 12,573 views

This covers two items, a special tool rest and the round cutters are available by phone orders only.

 

Captured Bowl Rest ·
By: Gerard Merchant
February 03, 2012 · 394 views

The use of a captured tool rest. My process for turning hollow vessels, in our first year of turning. Visit us @ https://www.etsy.com/shop/GMStudiosPens

 

3-in-1 Steady Rest and Articulated Hollowing Rig ·
By: Ron Brown
December 18, 2011 · 11,343 views

Swing Arm Steady Rest and TMI Dave Hout designed articulated arm hollowing rig demonstrated by Ron Brown

 

Crude spindle steady ·
By: Bob Hamilton
November 16, 2011 · 52,484 views

This is the crude spindle steady I made a few years ago and it works well enough that I have never bothered to change it. I don't use a steady very often and this one seems to do the job when I need it. These clips are excerpted from my tall, thin stemmed goblet video where they were edited out due to the length of the video.

 

Making of a Steady Rest ·
By: WoodenNicol
April 02, 2009 · 26,846 views

From Start to finish, making a lathe steady rest.

 

Return to Turning Videos

Great Bargains


Heavy Duty Live Center

On Sale for only $16.53

List Price: $19.95

Click here for more information or to purchase

 


Dremel Rotary Tool Kit

On Sale for only $139.00

Save $60.99 (30%)

List price: $199.99

Click here for more information or to purchase


Roller Stand

On Sale for only $23.79

Save $6.11 (20%)

List Price: $29.90

Click here for more information or to purchase

 


Easy Wood Tools - Easy Start Rougher + Finisher + Detailer

On Sale for only $159.99

List price: $206.97

These tools have the smaller 9" maple handle and are 12.5" overall.

Click here for more information or to purchase


NOVA 48232 G3 Reversible Wood Turning Chuck

On Sale for only $99.00

Save $60.99 (38%)

List price: $159.99

Click here for more information or to purchase

Powered by Google

Our Newsletter

We update our home page about monthly to feature a new project, a new article, and a new and hot tool. Then we create a newsletter to alert our subscribers.
We never let anyone use our list, and our subscribers have been wonderfully loyal as a result.

We hope you will try it out!

Sign Up For Our Newsletter

A Sampling of our Sponsors:
(Visit the Vendor's Corner above to see all our sponsors)

Hunter Woodturning Tools
Artisan Ideas
Imaginlay

(Click any Ad to go to our Sponsor's Website)