Wood Turning Channels From Woodturning Online

Woodturning Online Videos

Welcome to the Woodturning Online Videos page.

This video content was created by woodturner, Rick Morris. He has created a way to monitor all the videos in YouTube that are woodturning related.

Each month, Rick updates the video listings below. If you would like to learn about new videos, sign up for our free newsletter where we will list the top 20 videos each month.

Any categories in BOLD have sub-categories to help you narrow down your search.

Roughing Out Videos (183)

Or click here to: Search All Videos

Rough turning an Oak bowl.
By: tfturning
September 01, 2019 · 141 views

Started a little wobbly due to the log being mounted slightly off balance, once the corners had been knocked off normal service was resumed. Most of the footage is a 8x normal speed. Now this bowl is off to the microwave for a drying cycle before I sand and finish with beeswax. Thanks for watching please like and subscribe :)

Rough turning spalted birch
By: The Riggs workshop
August 26, 2019 · 34 views

I found a few of these spalted silver birch logs in amongst my log burning pile .. it would be a crime not to do something with them . So ive rough turned them before leaving them to dry ..

Spalted endgrain birch woodturning
By: Scary Catches
July 13, 2019 · 115 views

Roughing out a bit spalted endgrain birch,then it will dry more,and then get finished. Cup tool 15mm HSS.

Laburnum roughing woodturning
By: Scary Catches
June 23, 2019 · 53 views

Testing a new mount place for my Gopro. Its on 60fps,but its not enough to get rid of flickering from the ledlight.I will try to change from NTSC(60HZ) to PAL(50HZ). I use Movavi to editing my videos. The wood is Laburnum,it will dry more for a month before i take the finishing cuts,and sanding. The lathe is a Stratos Twister fu-200. I have the smaller one as well (Miditec fu-175) Both are very good lathes :)

Rough Turn and Core Twelve Inch Box Elder -- Edited Version
By: Ronald Werner-Wilson
June 18, 2019 · 11 views

This video was edited from a Facebook Live segment recorded on June 15, 2019. The exterior of a twelve inch Box Elder blank is rough shaped and cored.

Rough Turn and Core Twelve Inch Box Elder -- Complete FB Live Video
By: Ronald Werner-Wilson
June 15, 2019 · 4 views

This video was edited from a Facebook Live segment recorded on June 15, 2019. The exterior of a Box Elder blank is rough shaped and cored.

A bit of fun rough turning a London Plane bowl in 10 minutes (x3 speed)
By: Mike Waldt
June 10, 2019 · 5,267 views

Simon Hope: http://www.hopewoodturning.co.uk/ Yorkshire Grit: http://yorkshire-grit.com/ Hampshire Sheen: http://www.hampshiresheen.com/ Easy Wood Tools: http://www.easywoodtools.com/ Easy Wood Tools at Amazon UK: https://www.amazon.co.uk/Easy-Wood-Tools-Chuck-M33-3-5/dp/B07664VKFB/ref lp_8318174031_1_13?srs 8318174031&ie UTF8&qid 1529428204&sr 8-13

Rough turning and coring a bowl with Woodcut bowl saver. Part 2
By: B.W. Woodturning
June 06, 2019 · 103 views

Part 2. Hope you enjoy the process.

Rough turning and coring a large bowl with Woodcut bowl saver. Part 1
By: B.W. Woodturning
June 06, 2019 · 172 views

Here I show the process of rough turning a large oak bowl, before I core it with my woodcut bowl saver. I also tell a bit about why seel quality matters more then the brand of gouges.

Part 2 : Roughing a maple bowl (Woodturning)
By: Christian Noël
May 18, 2019 · 89 views

Part 1 : Roughing a maple bowl (Woodturning)
By: Christian Noël
May 17, 2019 · 138 views

40/40 grind

Woodturning - Rough Turning Of A Larch Bowl
By: Kotodama
May 12, 2019 · 76 views

This time I put quite a big chunk of larch on my stratos xl and rough turned it into a bowl. Now it is drying a couple months until I can finish it.

Large Natural Edge Walnut 1: Rough Turn and Form Tenon
By: Ronald Werner-Wilson
April 02, 2019 · 2 views

Natural Edge Walnut 1: Rough Exterior
By: Ronald Werner-Wilson
April 02, 2019 · 8 views

In this video, I rough turn the exterior of a natural edge walnut blank.

Plum 1: Rough Turn Exterior
By: Ronald Werner-Wilson
April 02, 2019 · 3 views

This piece of plum was harvested from my Mother's property. In this video, I rough turn the exterior and create a tenon on the bottom of the blank to attach it to a chuck so that a smaller bowl can be cored from this one.

Tuesday Tip 38, Evaluate vessel surface while roughing out blank.
By: Lyle Jamieson
February 26, 2019 · 638 views

Please welcome a new sponsor Starbond to my YouTube family. I have been using Starbond CA glues for decades. Check them out at https://www.starbond.com Use promo code: LYLE15 at checkout for 15% off discount. Please see my website http://www.lylejamieson.com for all the resources and tool store. Every tool listed has more information details. See not only the right tools but tips and techniques on how to use them. I have archived my articles written for publications and each of my newsletter broadcasts have all the Q&As listed by topic and indexed table of contents. Please support my sponsors. They make it possible for me to produce this content. http://www.hunterwoodturningtool.com 612-718-7926 http://www.thompsonlathetools.com 440-241-6360 http://www.starbond.com 800-900-GLUE(4583)

Woodturning - 2 Green Bluegum Bowls for Drying - Conrad P. Woodturning
By: Conrad P. Woodturning
January 07, 2019 · 247 views

Today I rough turn some bowls using some logs I had sitting around. The timber is Bluegum (a species of Eucalyptus native to Australia). The blanks should be ready for finished turning in 4-6 months time. Thank you for watching my video, and if you enjoyed it, please consider giving it a like, commenting below and subscribing to my channel so you don't miss out on any of my future videos. --------------------------------------------------------------------------------------------------- Disclaimer: I am NOT a professional woodturner, and the videos posted on this channel, along with any woodturning practices are for demonstation and entertainment purposes only. Woodturning can be a very dangerous craft if appropriate precautions are not taken. Woodturners are responsible for their own safety, and should seek proper training before attempting turning. 'Conrad P. Woodturning' will not be held responsible for any accidents/injuries that people may recieve from woodturning activities.

#4 Roughing out 4 5in green bowls, timelapse
By: Mike T
December 05, 2018 · 231 views

First time slabbing out blanks from logs. Time lapse of roughing out 5 inch bowls from the smaller slabs of choke cherry.

Turn square blank to round easy
By: Lyle Jamieson
October 09, 2018 · 1,721 views

I use the lathe to turn square to round. Easy quick and safer than using a band saw. More important I am in control of axis and scale by roughing it out on the lathe. Please see my website http://www.lylejamieson.com for all the resources and tool store. Every tool listed has more information details. See not only the right tools but tips and techniques on how to use them. I have archived my articles written for publications and each of my newsletter broadcasts have all the Q&As listed by topic and indexed table of contents. Please support my sponsors. They make it possible for me to produce this content. http://www.hunterwoodturningtool.com http://www.thompsonlathetools.com

Roughing large sugar maple wood bowl. #woodturning
By: Deer Meadow Woodturning
September 30, 2018 · 43 views

Time lapse video of me roughing the outside of a 18” 48lbs piece of sugar maple wood.

Roughing Out
By: Roper Woodturning
July 31, 2018 · 12 views

While waiting for the sanding sealer to finish drying on my Box Elder piece I got started roughing out a new vessel. Scored some fairly fresh Locust and just had to see what was inside. Turning wet locust make you feel like a hero. Plus by hollowing it out partially I can speed up the drying process while minimizing checking. #roperwoodturning #woodturning #lathe #onthelathe #maker #shoplife #dirtyhandscleanmoney #robertsorby #powermatic

Rough Turning Cherry Bowls - Sawdust Factory Woodturning
By: Josh Bayer
July 08, 2018 · 1,891 views

Sawdust Factory Woodturning works on rough turning some cherry bowls cut from a dead tree. This tree has been dead standing for a couple years. The tree was rotting from the base up. ___ Music: You're No Help - Silent Partner https://youtu.be/wK6bwkuUYRo Title: You're No Help Artist: Silent Partner Genre: Pop Mood: Funky Download: https://www.youtube.com/audiolibrary/... ––– • F.A.Q: How to use music https://goo.gl/zNKFGu ––– • Main Playlists: Artists: https://www.youtube.com/channel/UCht8... Genres: https://www.youtube.com/channel/UCht8... Moods: https://www.youtube.com/channel/UCht8... ––– • Follow us: Facebook https://goo.gl/BBxPNx Twitter https://goo.gl/WJnMWV Instagram https://goo.gl/5EgBhP SoundCloud https://goo.gl/KfElaU Google https://goo.gl/eDXHbT –––

Madrone Burl Rounding
By: Roper Woodturning
April 22, 2018 · 15 views

Taking a piece from square to round is rough. Madrone burl.

#47 Osage Orange Live Edge Rough Turn
By: Austringer Creations
April 16, 2018 · 65 views

In this video I start on another commissioned piece, a live edge bowl. A customer gave me a few pieces of Osage Orange and wanted a live edge bowl turned from one of them. Today, I rough turn the piece into the beginnings of the bowl.

TUTORIAL 11: NOT SO ROUGH, ROUGHING GOUGE
By: CL Woodturning
April 15, 2018 · 307 views

Just my take on how to use a roughing gouge to make smoother, nicer cuts before your finishing detail. A TURN FOR THE GOOD Auction live! 14th - 21st July, 2018 https://www.facebook.com/groups/aturnforthegood https://mobile.twitter.com/aturnforthegood?lang en

Makin shavings
By: Roper Woodturning
March 31, 2018 · 15 views

Last Connie Hoard Piece Roughing 2
By: Will Coffman
March 26, 2018 · 7 views

Last Connie Hoard Piece Roughing 1
By: Will Coffman
March 26, 2018 · 13 views

Wood Turning Club - Rough Bowl Turning
By: caitlan the cat
March 16, 2018 · 1,233 views

On Wednesday night at Wood Turning Club I decided to turn another of the rough turned bowls that Lee and Lynn sent me from America. I had to turn the chucking point to make it fit my chuck first and then wanted to make the rim of the bowl really, really thin.

Wood Turning Club - A small rough turned bowl
By: caitlan the cat
March 11, 2018 · 1,792 views

This is one of the bowl blanks that I was sent from Lee and Lynn in America. I think the shape came out really well and the finished bowl looks really nice.

Woodturning- Roughing a maple bowl
By: Amy Grigg
March 08, 2018 · 558 views

Using the push cut and a Sorby 1/2' gouge. Hard Maple bowl 850 rpm

Roughing out an Ash Bowl
By: Bryce Roebel
February 23, 2018 · 186 views

Rough turning an ash bowl to around one inch thick. I will let this dry in it’s own shavings for around three weeks and then turn it down to it’s final form on the lathe again.

Rough turning a bowl from a green piece of red oak
By: John Baker
February 22, 2018 · 27 views

Turning is new to me so subscribe to follow my journey. Just wanted to make a vid for fun this video is for your entertainment so I hope you enjoy. Here is a link to part two on this video https://youtu.be/nNDvfYNrk3E

Rough Turned - Oven Dried - Elm Fruit Bowl with part Natural Edge Rim
By: Nathan Cumming
February 10, 2018 · 836 views

In this video I rough turn a large piece of part seasoned Elm I acquired last year. I start by roughing out the blank so that i'm able to dry it in the oven to allow it to be finish turned sooner. The roughed out bowl is dried in the oven at 80 degrees C for 1.5hrs. It went from weighing 1,700g and 30% moisture to 1,400g and 12% moisture. The blank is the remounted on the lathe and finish turned. I sand it to 320 grit and then apply finishing oil. I hope you enjoyed this video. Thank you to all my Subscribers for your continued support. Please share this video and my channel via social m

Roughing out wet Elm Bowl
By: Roper Woodturning
February 02, 2018 · 26 views

Shear cutting the outside shape of this wet Elm bowl. 20' x 5'

Wet Maple Woodturning
By: Roper Woodturning
February 02, 2018 · 25 views

Roughing out a very wet hollow vessel.

Rough Turned - Oven Dried - Cherry Crotch Bowl
By: Nathan Cumming
January 20, 2018 · 998 views

In this video I rough turn an 11' block of cherry crotch with the intention of leaving it to dry naturally. However, after waiting a week I decided to experiment with drying a bowl blank in my oven. I put the rough turned blank in the oven at 100 degrees C for an hour and it came out bone dry. There were a few cracks that had formed by the piece was still solid. I then finish turned the bowl finishing with Yorkshire grit and Hampshire sheen. The few cracks that remained after turning and sanding were filled by the process of wet sanding with oil and burnishing with shavings. The entire finis

Turning Chips! [Roughing a Green Bowl Blank]
By: treesandclay
November 19, 2017 · 10,241 views

It's been a while since I have gotten a fresh log. I popped up a camera to capture the process of gleaning the largest bowl available from one half. Before this video the log was cut in half and the resulting blank was cut to round on the bandsaw.

Woodturning Walkthrough of Walnut Bowl Blank Roughing - How to - Sawdust Factory Woodturning
By: Josh Bayer
November 01, 2017 · 4,358 views

In this video i walk through my typical roughing process for a bowl blank that will be set aside for drying. We go from Log to roughed out bowl blank in this video. Covering each step of the process while going over a few of my tricks to making a successful bowl blank that will survive the drying cycle. The dry process takes about 12-18 months depending on bowl thickness/size and the moisture content of the air. After drying this bowl will go back on the lathe for final finishing. Thanks for Watching. if you enjoyed the video check out the rest of my channel for more woodturning video projects and How-tos

Rough Turning an Elm Bowl With Burr Figuring
By: Nathan Cumming
October 10, 2017 · 1,277 views

In this video rough turn a piece of green Elm that I prepared from the haul of Elm i received a few months ago. When cutting the logs I noticed there were a few small burrs on the side of one so cut the log in such a way as to allow the burr figuring to show through on the base of the blank. The piece is part seasoned, some of the wood is quite dry but other parts very wet. I turn it down to an even wall thickness of 15mm and leave it to dry in the shavings. I shouldn't be long before it's dry enough to finish. I hope you liked this video. Thank you to my Subscribers, if you haven't Subscrib

Rough Turning a Bowl #04
By: Made by Brent
September 29, 2017 · 47 views

This is how I rough turn a bowl. This allows the wood to dry faster and is less likely to crack. if you would like to contact me my email is madebybrent@gmail.com if you would like to learn more about what I do you can go to my website brentmichaelarnold.wordbress.com

Outboard Turning
By: Lee Burkholder
August 24, 2017 · 2,259 views

Cumberland Valley Wood Turners, lathe, wood turning, outboard turning, wood turning,

Tiszafa feldogozás, woodturning yew bowl
By: Szabó Janó
August 06, 2017 · 811 views

Sziasztok! 10 éves kisfiammal Milánnal esztergálunk, és egy egy munkáról töltünk fel videókat. Aki szeretni látni hogy készül el fából pl egy tál vagy egy esztergált dolog akkor jó helyen jársz.Ma egy tiszafa törzset dolgozok fel, hogy hamarabb megszáradjon. facebook oldalunk: https://www.facebook.com/diszelifaesztergalyosok/ instagramm: https://www.instagram.com/szabojano

35 seconds of relaxation therapy
By: Motley Dog Woodturning
July 04, 2017 · 28 views

Rough turning the outside of an alder bowl

Roughing Out a Cherry Bowl
By: RickTurns
July 03, 2017 · 27,196 views

In this video, I start with a large slab of fresh cherry, and rough turn a 14' bowl. In subsequent videos, I will demonstrate building and using a drying box to dry the roughed blank, finish turning the roughed blank, and finally decorating the bowl with pegs. The music during the close of the video, Happy Little Elves by Audionautix, is licensed under a Creative Commons Attribution license (https://creativecommons.org/licenses/by/4.0/) Artist: http://audionautix.com

Woodturning with Tim Yoder ... Catches Part 1: Roughing Gouge
By: woodturningwithtim1
July 03, 2017 · 29,003 views

This is the first in a series of videos using slow motion video to explain how woodturning catches happen. This segment covers the Roughing Gouge and what you should do and shouldn't do. You can find instructional DVDs, Tim’s Tools and the Elbo Hollowing Tool on the Woodturning with Tim website: http://www.woodturningwithtim.com Please support our sponsors. Without them we could not bring you these videos. Robust Lathes: http://www.turnrobust.com/ I am a Robust dealer (which adds nothing to your costs) and I am more than happy to help you pick out and configure your new lathe. Thompson Lathe Tools: http://thompsonlathetools.com/ These are the finest, long lasting turning tools on the market. I have used them since our first shows on PBS. music by Kevin MacLeod 'Exit the Premises' Royalty Free

Rough turning a bowl time lapse
By: Todd Halleman
July 02, 2017 · 112 views

Here is a quick little video of me rough turning a bowl made from black ash Burl. In a future video I will show me finish turning it.

Woodturning - Rough Turning Walk Through - Moldy Maple Rough Turning
By: Josh Bayer
May 07, 2017 · 6,122 views

Welcome back to The Sawdust Factory. In this video I walk thought the entire rough turning process using a piece of Silver Maple. This was left over from the Silver maple Twin bowls video i did some time back. I hope you enjoy the video. Check out my channel for other woodturning videos here at The Sawdust Factory

Rough-Turning a Natural edge bowl, (part 3) From a log to a bowl with Sam Angelo
By: WYOMINGWOODTURNER
April 06, 2017 · 9,757 views

Rough-Turning a Natural edge bowl (part 3) From a Log to a Completed bowl Link to series' playlist: https://www.youtube.com/playlist?list PLL5-IWEcq6B-hymSlYZxdWTeVPTFRNe9Z Sam continues his 4 part series, 'From a Log to a Completed Bowl' by rough-turning a wet Honey Locust bowl. Rough-turning wood is the first step in the drying process of a bowl. In the last video (part 4) in this series Sam completes a burl bowl that has reached the proper moisture content.

Rough Turning a Birch BOWL, part 2 Sam Angelo wyomingwoodturner
By: WYOMINGWOODTURNER
April 01, 2017 · 17,524 views

Part 2: From a Log to a Completed Bowl (series) Rough-turning a bowl Link to this series' playlist https://www.youtube.com/playlist?list PLL5-IWEcq6B-hymSlYZxdWTeVPTFRNe9Z Sam continues his 4 part series, 'From a Log to a Completed Bowl' by rough-turning a very wet log of birch. Rough-turning wood is the first step in the drying process of a bowl. In the last video in this series Sam completes a bowl that has reached the proper moisture content.

Very Wet Rough Turn - Episode 70
By: Paul Lockwood
April 01, 2017 · 736 views

A trip down to the local mill where I picked up a good selection of wet wood, all for 3. Yes a good source of cheap but good wood which are all offcuts they could not use for fencing and sell off for firewood. The Oak especially is very wet, showing at around 27% on my cheap meter. So I decide to rough turn two Oak bowls and two Silver Birch smaller bowls. With the Oak being so wet and the grain running from top to bottom I decided to try and seal this with Shellac I mixed up from flakes before storing all the pieces away in a paper bag with the shavings. The workshop needed to be cleaned b

Woodturning - Rough Turning Pecan
By: Jason Lowrie
March 23, 2017 · 5,174 views

Most of the wood I turn is from downed trees I find in the free section of Craig's List. A few weeks back, I picked up a few logs from a pecan tree that had been felled about a year ago. The wood had been sitting out on the side of his house and developed some great spalting. In total I roughed out 10-12 bowls, a lidded box, and sealed a few spinal blanks. As these pieces dry, I'll have a few pieces to finish turn in 8-10 months once dry. Thank you for watching.

Rough turning a hollow form
By: Tommy Akridge Designs
March 23, 2017 · 2,151 views

Mark Silay https://youtu.be/53gfCc9sskw My name is Tommy Akridge, I am a small town wood turner working on wooden bowls, segmented bowls and vases. some of my work could be considered art and also consist of Urns, vases and boxes. I have been turning for just a few years and I have found that I love it. I get lost in my work and that helps me cope with my the day to day work life. Showing my work on YOUTUBE has changed the way I turn, I enjoy showing others what i'm doing and maybe them be better turners. Thank You For Watching Tommy Drifting 2 by Audionautix is licensed under a Creative Commons Attribution license (https://creativecommons.org/licenses/by/4.0/) Artist: http://audionautix.com

Episode 2 Series Hollow Form, Quick Roughing
By: Daniel Vilarino
March 14, 2017 · 1,597 views

Hola/Hi! Este video está en Inglés, para verlo en Español por favor haz un click en el siguiente enlace: https://youtu.be/sdz0U8oDqvE ***This video is in English*** Este video es el segundo en una serie en la cual voy a ir mostrando varias técnicas que nos llevarán a la realización de una forma hueca. La primera fue encontrar el punto de balance entre puntas para poder levantar la velocidad del torno y facilitar el cilindrado de una pieza irregular. Dicho video lo puedes ver en el siguiente enlace: https://youtu.be/pwX7b75oUJI En este video, aprovechamos que la pieza está ya balanceada y que

Rough Turning - Episode 62
By: Paul Lockwood
March 11, 2017 · 314 views

I've started going through some of my old wood that I bought from the local mill. It was wet when I bought it and never sealed so some have quite a few cracks where I'm now seeing what I can make out of them. A couple of pieces I've started with where they originally looked pretty dry, but when turning them found the moisture content was up to around 17%. As I wanted to make lidded boxes out of these I need to rough turn them so that they dry a little more as they will warp meaning that the lids will not fit properly if finished now. Music Go (Instrumental) By Josh Woodward http://freemusicarchive.org/music/Jos... From The Free Music Archive http://freemusicarchive.org CC Attribution 4.0 International https://creativecommons.org/licenses/... Please Subscribe http://www.youtube.com/channel/UCJmcpalJi_xzP_iV3uXJj2w?sub_confirmation 1

Silent Woodturning Part 2: Rough to Round
By: Olympic Peninsula Woodturners
February 26, 2017 · 44 views

OPCAAW member Dan Marler shows the process of turning a vase from a rough wood blank. There is no sound track or spoken description.

Wet Rough Turnings - Episode 60
By: Paul Lockwood
February 25, 2017 · 604 views

Grabbing some of my early wood that has been on the rack for a few months now and still a little wet, I decided on a couple of turnings. The wood has never been sealed and does have cracks in places. No sanding and no finish, just a quick video to show to rough turned items that have been put away in a bag with shavings for a few months to see what happens. Music Shot Down (Instrumental) and Faded War (Instrumental) By Josh Woodward http://freemusicarchive.org/music/Jos... From The Free Music Archive http://freemusicarchive.org CC Attribution 4.0 International https://creativecommons.org/licenses/... Please Subscribe http://www.youtube.com/channel/UCJmcpalJi_xzP_iV3uXJj2w?sub_confirmation 1

Roughing green bowl
By: Al Hockenbery
February 04, 2017 · 1,129 views

This is a video of how I rough turn a bowl for drying. This video was taken by Jan and Carl Brown during a demo i did in January 2017 for the Tri-County Woodturners. The demo was 3 parts. powerpoint overview, rough a bowl from wet wood (you will see the overhead camera get wet), and mounting and returning a dried bowl.

Lathe roughing out
By: Jamie Pinner
November 23, 2016 · 44 views

this is pretty much my rough out process now... its quick and very rough...

Roughing out a Cherry bowl from the log
By: Donny's Variety Channel Creative Creations
September 19, 2016 · 318 views

This is a beautiful roughout. It is a great piece of Cherry. Hope you enjoy the viedo.

Roughing out an Ambrosia Maple bowl using a wormscrew.
By: Donny's Variety Channel Creative Creations
September 11, 2016 · 5,297 views

I am using a wormscrew on this 11 inch bowl blank.

Wood Turning - Wet Log to Blank to Bowl - Time Lapse
By: Mike Waldt
September 09, 2016 · 14,833 views

My process of cutting logs on the band saw to bowl blanks and rough turning them. This video is a time lapse record of the procedure...just a bit of fun really :)

Wood Turning - Rough Turned Wet Beech Bowl
By: Mike Waldt
August 28, 2016 · 16,977 views

I rough turn a wet Beech bowl NZ Woodturning - https://www.youtube.com/channel/UC3-0S7vXfwYY2jj5EkMpymA

Rough turning a green bowl
By: Stormy Woodworks
August 01, 2016 · 359 views

In this episode I rough turn a green (wet wood) bowl.

FINISHING ROUGH-TURNED BOWLS woodturning with Sam Angelo
By: WYOMINGWOODTURNER
June 27, 2016 · 10,431 views

In this video Sam trues up several dry, rough-turned bowls on the way to completion. He shows some important steps in this process.

Rough turning and drying a wood bowl.
By: Tommy Akridge Designs
June 26, 2016 · 4,911 views

Rough turning and drying a bowl with a sealant. My name is Tommy Akridge, I am a small town wood turner working on wooden bowls, segmented bowls and vases. some of my work could be considered art and also consist of Urns, vases and boxes. I have been turning for just a few years and I have found that I love it. I get lost in my work and that helps me cope with my the day to day work life. Showing my work on YOUTUBE has changed the way I turn, I enjoy showing others what i'm doing and maybe them be better turners. Thank You For Watching Tommy Whatdafunk by Audionautix is licensed under a Creative Commons Attribution license (https://creativecommons.org/licenses/by/4.0/) Artist: http://audionautix.com

Rough Turning Water Oak Bowl
By: Tommy Akridge Designs
June 03, 2016 · 6,527 views

Rough turning a bowl and packing it to dry. I will remove it later and check the moisture content till it is dry to finish. bowl is 10' deep and 20' across the top and made from Water oak, a tree found in the southern gulf states alone the coast. My name is Tommy Akridge, I am a small town wood turner working on wooden bowls, segmented bowls and vases. some of my work could be considered art and also consist of Urns, vases and boxes. I have been turning for just a few years and I have found that I love it. I get lost in my work and that helps me cope with my the day to day work life. Showing

Last bowl on rikon?
By: yak branson
May 23, 2016 · 5,639 views

A day of ruffing out some bowls and decided to video this small bowl that could be the last bowl i do on the rikon.

Wood Turning - Finishing a Rough Turned Bowl
By: Mike Waldt
April 17, 2016 · 7,546 views

I finish turn an Ash bowl that I roughed turned about 14 months ago. UKIWS - http://www.ukiws.co.uk/ Jimsons Stuff: https://www.youtube.com/channel/UC6h82LH3PtdiSHaj_7f09Fg Todd Halleman: https://www.youtube.com/user/tohall18 Martin Saban-Smith's Video; https://www.youtube.com/watch?v yy3KQKbjdbg

Caffeine Kick! Speed Roughing Cherry Bowls! 10 Minute Bowl
By: Peter Stewart
April 05, 2016 · 539 views

What happens when you rough bowls on super mega high caffeine??? -------------------------------------------------- My website: www.peterturnswood.com ----------------------------------------- To see my vlog and follow-up channel, go to my main channel by clicking 'Peter Matthew' up above. On my main channel, look to the right side of the screen where it says 'Featured Channels'. Under 'Featured Channels' is 'Peter Matthew 2'. Click that and subscribe to that channel :) ------------------------------------------------------------------------------- Want to do a sticker swap? Send me an email: peterturnswood@gmail.com Want to send me a powermatic lathe (please do)? Mailing address: Peter Matthew 6388 East Executive Drive Westland, MI 48185 Contact me: peterturnswood@gmail.com My eBay store: http://www.ebay.com/usr/dste6080 Subscribe to my YouTube Channel! I post videos every Friday!

Roughing Out a Natrual Edge Bowl
By: Brian Havens
March 26, 2016 · 15,623 views

The Apple tree I recently dissected did not go along with my plan. I was planning a couple other videos before I go back to the task of roughing out the half-logs into bowls. The Anchor-seal bought me some time, but one of the pieces started to crack. Time to get busy roughing, starting with a piece that are destined to be natural-edge bowl.

Bowls Cove Ruffing cut
By: Al Hockenbery
March 26, 2016 · 82 views

This clip is from demo on gouges given to the tri-county woodturners. It shows my favorite way to begin roughing a bowl or hollow form, I use a cove roughing cut with an A frame stance. Thanks to Jan Carl for the great video

10' maple ruff turn real time
By: yak branson
March 09, 2016 · 51 views

My fun time! Love makin those shavings.

Rough Turning Beech Bowls
By: Mark Sanger
March 04, 2016 · 6,166 views

Just a quick demonstration of how I rough out my bowls. This is not an instructional video.

Wood turning # 36 mystery crotch wood rough out
By: Woodslee Summercraft
February 14, 2016 · 2,040 views

I love the process of finding wood getting the chainsaw, cut it open to find natural beauty inside, turning it round and then waiting to finish it once it dries. These are some of my go to guys for inspiration Mike Waldt https://m.youtube.com/user/TheCymruBoy Carl Jacobson https://m.youtube.com/user/haydenHD Eddie castelin https://m.youtube.com/user/capneddie Gary Lowe https://m.youtube.com/channel/UCgdG-Vh5Uj2GNdVgnsDEMtA Templeboy Turnings Steve Twydell https://m.youtube.com/user/stevo15771 Robbie the wood turner https://m.youtube.com/user/Robbiethewoodturner Steve Crawford, supplier of amazing wood blanks http://crawford-studio.com

Completing a Rough-Turned Lidded Box: Woodturning with Sam angelo
By: WYOMINGWOODTURNER
February 12, 2016 · 9,192 views

Sam completes a lidded box that was first rough-turned. After a period to allow for drying, he puts the lid and base back on the lathe to finish the project.

Rough Turning an American Elm Bowl
By: Peter Stewart
February 12, 2016 · 1,488 views

This video covers the rough turning of an American Elm Bowl. Larry Martin:https://www.youtube.com/channel/UCcc2... My website: www.peterturnswood.com My vlog channel: https://www.youtube.com/channel/UCiST... ------------------------------------------------------------------------------- If you would like a sticker, send me a stamped self addressed envelope or one of your own stickers with your address. Peter Matthew 6388 East Executive Drive Westland, MI 48185 Contact me: peterturnswood@gmail.com My eBay store: http://www.ebay.com/usr/dste6080 Subscribe to my YouTube Channel! I post videos every Friday! Music: Guts and Bourbon by Kevin MacLeod is licensed under a Creative Commons Attribution license (https://creativecommons.org/licenses/...) Source: http://incompetech.com/music/royalty-... Artist: http://incompetech.com

Roughing Out Bowls 1 by David Woodward
By: David Woodward
January 08, 2016 · 657 views

This is my first attempt at a video, very kindly edited by my good friend John Osborn. Without who s help I would not have this done. I m a basic bowl and platter production turner, Turning for many shops and department stores also private people. Although I have retired from commercial turning, It s still a passion that I enjoy, By making this video I just hope it may be of some help to budding turners starting out.

RoughingNEoutside
By: Al Hockenbery
October 20, 2015 · 379 views

This video is not a good how to but more of an overview of why I use the side ground bowl gouge to turn natural edge bowls. I am not particularly fast and I can turn the outside of medium sized bowl in a few minute. The Ellsworth grind with a pull cut leaves a smooth surface and cuts the bark cleanly.

Wood turning #4 rough out live edge maple bowl
By: Woodslee Summercraft
October 18, 2015 · 1,708 views

Roughing out a wet maple live edge bowl, 1' thick to be finished later when dry.

Wood turning #3 roughing out wet maple bowl
By: Woodslee Summercraft
October 16, 2015 · 780 views

this is how I prepare wet wood to dry quicker and make turning easier later. hopefully preventing cracks.

Rough turning an ash bowl
By: Turntastic Wood Designs
September 26, 2015 · 153 views

I learned a hard lesson about safety on this one. But it came out ok in the end. See where I finish turn this vase here https://www.youtube.com/watch?v fhqyDSK2x_E Please visit my store at htps://etsy.com/shop/turntasticwooddesign

Desvastando un Cuenco de Arce 8' x 3' de alto
By: Adam Woodturner
September 15, 2015 · 651 views

desvastando un cuenco de arce y dejandolo secar para luego terminarlo. - Captured Live on Ustream at http://www.ustream.tv/channel/woodturningwood

Rough turn coffee tree bowl blank
By: H F Bowern Designs - Harold Bowern
September 10, 2015 · 635 views

Welcome Back!! Well in this video I am turning a coffee tree bowl blank. I got this blank from my local wood supplier A&M Wood Specialty in Cambridge Ont. The blank is approx 6 1/4' round and for the most part 4' tall. It was covered in wood preserver by A&M staff. I paid 6.00 for the blank. I bought another blank which I that I hope to turn in month or so. This is my first attempt at turning wet wood and I have learned quite a bit about tool presentation as well as making sure the tools are kept sharp. I have turned the blank down to approx 1' thickness in the walls and base and I have pu

woodturning - how to roughout a lidded box
By: George Watkins
September 04, 2015 · 4,225 views

In this video I talk about and demonstrate the importance of rough turning when making a turned box.

Vaciado con Raspador de nariz convexa 60 grados
By: Adam Woodturner
August 30, 2015 · 7,040 views

Vaciado con Raspador de nariz convexo 60 grados angulo de corte. Lo que me olvide fue subirle la velocidad al torno luego de hacerle el hueco con la mecha forstner que lo tenia en 400 RPM. Usualmente para vaciados para que corten limpio y como mantequilla le subo la velocidad entre 1500-2000 RPM.

Rough Turning More Bowls A Lot of Shavings
By: Peter Stewart
August 17, 2015 · 1,195 views

This time I rough turned some more bowls out of green wood. I turned three out of walnut, two out of oak, and three out of maple. Once I had turned the bowls, I checked that the wall thickness was even, filled any small checks with thin CA glue, and sealed the end grain with end grain sealer. Some of the really green bowls I packed in a paper bag with shavings, but all the others I just set on the shelf. Now all I have to do is wait. ---------------------------------------------------------------------------------------------------------------- Contact me: Peterturnswood@gmail.com My eBay store: http://www.ebay.com/usr/dste6080

Roughed bowl speed challenge
By: Adze Woodturning
July 16, 2015 · 3,210 views

Steve Antonucci from my turning club challenged me to rough a bowl in five minutes. It took me 21 minutes and I felt like I was rushing.

Rough Turned Walnut Natural Edge Bowl
By: Daniel Vilarino
July 15, 2015 · 572 views

Hola/Hi! ***This Video is in English*** Este video está en Inglés, si prefieres verlo en Español, por favor haz un click en el siguiente enlace: http://youtu.be/N2DeRRLke4I En este video, hago el torneado primario (inicial, en basto, en bruto) de una pieza de nogal. Lo que me gustó de este bloque de madera es que la corteza aún estaba bien adherida al resto del tronco, por lo cual lo hice dejando un borde natural. Dejé el espesor de las paredes de 1/10 del diámetro del cuenco. De esa forma, cuando haga el torneado final, tendré suficiente espesor para llevarlo de nuevo a redondo y lograr es

Rough Turnings
By: Daniel Vilarino
July 10, 2015 · 394 views

Hola/Hi! Este video está en Inglés, si prefieres ver la versión en Español, por favor haz un click en el siguiente enlace: http://youtu.be/544aJNkJCTg ***This video is in English*** En este video aprovecho a hacer algunos torneados en bruto (torneados en basto, torneados primarios) y al mismo tiempo estrenar la gubia de cañón grande a la cual le había hecho el mango hace tiempo atrás, para ver cómo funcionaba en el desbaste de material y también el vaciado del cuenco. En unos pocos días hice tres torneados en basto, el primero, que es el que muestro en el video, es de una pieza de Nogal, los

Torneados en bruto
By: Daniel Vilarino
July 10, 2015 · 2,665 views

Hola/Hi! ***This video is in Spanish, if you prefer to see the English version, please make a click in the following link: http://youtu.be/OVsTDqibUK8*** Este video está en Español En este video aprovecho a hacer algunos torneados en bruto (torneados en basto, torneados primarios) y al mismo tiempo estrenar la gubia de cañón grande a la cual le había hecho el mango hace tiempo atrás, para ver cómo funcionaba en el desbaste de material y también el vaciado del cuenco. En unos pocos días hice tres torneados en basto, el primero, que es el que muestro en el video, es de una pieza de Nogal, los

Rough Turning a Bowl -starting with a screw chuck
By: WYOMINGWOODTURNER
July 05, 2015 · 16,530 views

Sam demonstrates the use of the screw chuck in woodturning. He rough-turns a small bowl beginning with a screw chuck and completes the project with no tailstock support.

Roughing out a bowl
By: RickTurns
June 19, 2015 · 9,660 views

How I rough out a bowl from a half-log

ROUGHING CUTS WITH A CHAINSAWN BLANK by Reed Gray aka Robo Hippy
By: robohippy
April 27, 2015 · 5,869 views

Robo Hippy gives us a few tips on Roughing Cuts with a Chainsawn Blank.

ROUGHING CUTS WITH GOUGES by Reed Gray aka Robo Hippy
By: robohippy
April 27, 2015 · 43,551 views

Robo Hippy tackles the task of Roughing Cuts With Gouges. Sharing some of his personal techniques and tools used.

Le PicBois #7 - Rough Turning
By: Pat Lap - Le PicBois
April 04, 2015 · 1,810 views

[ Rough turning of a maple bowl ] Support me on Patreon: https://www.patreon.com/lepicbois Website: http://lepicbois.net/ YouTube: https://www.youtube.com/lepicbois Facebook: https://www.facebook.com/AtelierLePicBois Instagram: http://instagram.com/atelierlepicbois Twitter: https://twitter.com/atelierpicbois ________________________________________________________ Special Thanks: Easy Wood Tools: https://www.youtube.com/user/EasyWoodTools Carl Jacobson: https://www.youtube.com/user/haydenHD ________________________________________________________ I work for free and I pay my director with cookies… Please help me to buy some flour by clicking on the link below: https://www.paypal.com/us/cgi-bin/webscr?cmd _flow&SESSION Eqxer72hzstD4emcu5OgZQyXm9I2ypT2k-PiYKNyeyKlNpjGC7vCQoHglh8&dispatch 5885d80a13c0db1f8e263663d3faee8d96f000117187ac9edec8a65b311f447e

Roughing out a large bowl
By: Kim Gowney
April 04, 2015 · 190 views

Full length video of the roughing out of a large bowl in Ash

Le PicBois - Rough Turning [Trailer]
By: Pat Lap - Le PicBois
April 02, 2015 · 436 views

[ preview of an upcoming video ] Support me on Patreon: https://www.patreon.com/lepicbois Website: http://lepicbois.net/ YouTube: https://www.youtube.com/lepicbois Facebook: https://www.facebook.com/AtelierLePicBois Instagram: http://instagram.com/atelierlepicbois Twitter: https://twitter.com/atelierpicbois ________________________________________________________ Special Thanks: Easy Wood Tools: https://www.youtube.com/user/EasyWoodTools Carl Jacobson: https://www.youtube.com/user/haydenHD ________________________________________________________ I work for free and I pay my director with cookies… Please help me to buy some flour by clicking on the link below: https://www.paypal.com/us/cgi-bin/webscr?cmd _flow&SESSION Eqxer72hzstD4emcu5OgZQyXm9I2ypT2k-PiYKNyeyKlNpjGC7vCQoHglh8&dispatch 5885d80a13c0db1f8e263663d3faee8d96f000117187ac9edec8a65b311f447e

Rough Turn Oak Bowl
By: Peter Stewart
March 19, 2015 · 437 views

I rough turned a bowl this week out of some oak that was given to me. The wood is really wet so it'll have to sit for a year or so and dry before I can finish it. Time to exercise a little patience :)

Roughing an 8' Red Oak Bowl
By: Solway Wood Turning
March 08, 2015 · 49 views

A time lapse of a bowl being roughed from Red Oak ready to dry for 6 months before being finish turned and a finish applied.

Roughing A Red Oak Bowl
By: Solway Wood Turning
March 08, 2015 · 52 views

A time lapse of a bowl being roughed from Red Oak ready to dry for 6 months before being finish turned and a finish applied.

Rough Turning Maple Bowl
By: Peter Stewart
February 06, 2015 · 296 views

This week I rough turned a bowl out of a piece of Maple that I had outside for a while.

#2 Turning a rough bowl from wet wood
By: Frank B
February 02, 2015 · 318 views

Turning a rough bowl in damp, splatted silver maple.

Rough Turning an Oak Bowl
By: Steve Lindsley
February 01, 2015 · 11,586 views

My friend and co-worker Bob gave me a couple of oak logs from a tree that fell on his property. I was able to rough out 6 bowl blanks. In this video I show how I rough turn one of the blanks. The process was pretty much the same for the rest. The wood was dripping wet with sap and moisture so it will be a while before they are ready to finish turn. Turning wet wood is a lot of fun and I thank Bob for providing the material! Hope you enjoy the video. Comments are always welcome.

Log to rough turned bowls: Video 2
By: Adze Woodturning
January 20, 2015 · 338 views

Covers how I set up bowl blanks and a little high-speed turning.

Log to Rough Turned Bowls: Video 1
By: Adze Woodturning
January 20, 2015 · 322 views

Here I show my process for making green logs into rough turned bowls. This video covers From log to circular bowl blank and the process to get there.

How to Rough Turn a Box Blank
By: Mike Peace Woodturning
January 17, 2015 · 8,056 views

I explain why it is necessary to rough turn box blanks when turning green wood. I demonstrate how to hollow end grain box blanks with a spindle gouge including using the exciting back hollowing technique. I upload new wood turning videos regularly so Ya’ll come back, hear? As an Amazon Associate I earn from qualifying purchases from my Amazon shop https://www.amazon.com/shop/mikepeacewoodturning. You can download demonstration handouts, downloadable copies of articles I have published, and other useful woodturning information available on my website http://www.mikepeacewoodturning.com/resources-3/.

Rough Turning Bradford Pear Natural Edge Bowl-Borde Natural Torneado Inicial
By: Daniel Vilarino
January 04, 2015 · 3,316 views

Hola/Hi! Ojalá que hayan disfrutado de este episodio y si fue así, por favor realicen comentarios, dénle un 'me gusta' y suscríbanse a mi canal. ***I hope you enjoyed this episode and if that was the case, please make comments, give it a 'like' and subscribe to my channel.*** Si por algún motivo no les gustó, o hay algo que se pudiera hacer mejor, por favor también comenten. Siempre hay que tratar de mejorar! ***If for any reason you did not like it, or there is anything that I could do better, please let me know. There is always room for improvement!*** La música fue obtenida de sitios sin regalías que permiten su uso en videos. ***The music was obtained from a royalty free sites that allows its use in videos.*** Muchas Gracias!! ***Thank you so much!!*** Salud!! ***Cheers!!*** Daniel

#1 Rough turning a bowl, Common Oak
By: Yuval Lahav Woodturning
January 01, 2015 · 4,339 views

The first day of the new year brings with it also my first official video, and I hope the first of many! Patreon: https://www.patreon.com/YuvalLahav Instructables: http://www.instructables.com/member/yuvallahav/ Pinterest: https://it.pinterest.com/yuvallahav/ Facebook: https://www.facebook.com/yuval.lahav.16 Reddit: https://www.reddit.com/user/aforeignitalian/ Songs in this video are: 1. Fog Lake - erik 2. On Tour - on a town Both available for free from http://www.freemusicarchive.org Feel free to share and recommend this video to your friends and family, a thumbs up would be appreciated, and if this is your first time to my channel, you are most welcome to subscribe!

Rough Turning Walnut Bowl
By: Peter Stewart
December 27, 2014 · 619 views

I turned this bowl out of some walnut I had laying in the pile. The wood was still a little green so I left the walls a little thick to allow for warping. Once I had finished up turning I took the bowl out of my chuck and put it into a paper bag with shavings and taped it shut to slow the drying process. In a couple months or when the bowl has dried completely, I'll finish turning it.

Obtaining Wood and Rough Turning con SubtÃtulos en EspaÃ ol
By: Daniel Vilarino
December 14, 2014 · 1,004 views

This video is in English with Spanish captions ***Este video es en Inglés con subtítulos en Español*** In this video I wanted to give hope to the new woodturners --like myself a few months back-- who get anxious about where they are going to get wood --besides buying it-- for their pieces. ***En este video, quería darle aliento a los torneros nuevos --como yo mismo hace unos pocos meses-- que están ansiosos por conseguir madera --aparte de comprarla-- para sus trabajos.*** Also, I wanted to show the process of rough turning a bowl and how to prepare it for drying, until such a moment when

Rough Turning a Cherry Bowl.
By: Adze Woodturning
December 13, 2014 · 336 views

Rough Turning a Cherry Bowl with 60 Degree Ellsworth Bowl Gouge.

Wood Turning - Rough Turning a Wet Ash Bowl
By: Mike Waldt
November 27, 2014 · 13,089 views

I show the method I use to rough turn a 'wet' bowl, and store it to dry, to finish turn at a later date. I'm using the 5/8' bowl gouge by Carter & Son.. Gordon's Channel : https://www.youtube.com/user/GordRocks1 Carter & Son Tools at the Toolpost: http://www.toolpost.co.uk/index.html Guitar by Michael Berk: https://www.youtube.com/user/mikeberk810

Walnut Bowl (Roughing)
By: Brian Smith
November 26, 2014 · 246 views

This video is about Walnut Bowl (Roughing)

Rough turning an 19 inch ash bowl.
By: Fosscreations
November 21, 2014 · 71 views

19 inch Ash bowl beginning.

Roughing with the Skew Chisel
By: RickTurns
October 28, 2014 · 4,015 views

Woodturning: Using a skew chisel to rough down small spindle pieces. Music courtesy of Audionautix.com

Rough turning green bowl
By: Ray VanDerMei
September 23, 2014 · 305 views

In this video i show how i go from a log to a roughed turned bowl that i then let dry for several months before finishing.

Roughing Cut for Bowl turning: wyomingwoodturner
By: WYOMINGWOODTURNER
August 04, 2014 · 7,819 views

Sam Angelo demonstrates a 'scraping' cut for leveling a very out-of-balance bowl blank. Sam first saw this technique used by Bill Luce at the Utah Woodturning Symposium.

Rough Turning A Cedar Bowl
By: Steve Lindsley
August 03, 2014 · 12,773 views

In this video I rough out a cedar bowl from a log given to me by my friend Ellen. Her mother had a rather large cedar tree cut down and provided me with a couple of logs. Unforturnately the carpenter ants got to the log before I did and made a mess of it. I was able to salvage a few bowl blanks but most wasn't useable. I cut two blanks on the bandsaw but only show turning one. The process is pretty much the same for both bowls. I hope you enjoy...comments are always welcome.

Rough Turning a Lidded Box: woodturning
By: WYOMINGWOODTURNER
July 24, 2014 · 2,587 views

Sam demonstrates how a box blank of wet wood is rough-turned to be set aside to dry for later turning.

Rough turning a Sycamore bowl
By: BowlsByCharles
July 14, 2014 · 164 views

Rough turn a bowl from a bowl blank which was produced during the previous video.

Woodturning - Ash Natural Edge Bowl (roughing out)
By: Kim Gowney
July 08, 2014 · 304 views

This video is primarily for Debra who commissioned the bowl, it isn't intended as a tutorial. The first few still are of the half log the bowl eventually came from, the angle of the blank relative to the top was not favourable and so you see the huge offset in the initial mounting on the lathe, the end result though is the nicely balanced bowl at the end. The bowl will be coloured once the final turning is completed, I hope to video some of that too.

Woodturning: Microwaving Rough Turned Bowls
By: Roundabout Woodworks
June 25, 2014 · 23,529 views

I dry rough turned spalted sycamore bowls in the microwave and finish one on camera. (All microwaving is done off-camera... because watching that would be more boring than it was doing it.) (I address my 'wrong direction' cutting in an upcoming video.)

Finish Woodturning Rough Turned - Alcohol Soaked Bowl
By: As Wood Turns
June 20, 2014 · 8,896 views

http://www.AsWoodTurns.com This is a followup on the rough turned green bowl of a few weeks ago. The bowl is now dry after having been soaked in alcohol. This is about six weeks instead of the year typical (for me) of air drying an typical bowl. The bowl finished out at 11 inches diameter and 4 inches high. In this video I remount the now dry bowl to reform the tenon and the exterior. Then flip the bowl over into a chuck to turn the inside down to about 3/8' wall thickness. Finally, I flipped the bowl back around again into a set of home made cole jaws to turn the foot. After this experiment,

Part 2: Milling and shaping a Madrone Burl
By: WYOMINGWOODTURNER
May 27, 2014 · 3,877 views

In PART 2 Sam Angelo cuts a Madrone burl round on the bandsaw and shapes it on the lathe for future coring.

Rough Woodturning & Alcohol Soaking Wet Walnut Bowl
By: As Wood Turns
May 01, 2014 · 9,684 views

http://www.AsWoodTurns.com Now that I've return to my home shop and can again use my full sized lathe, I have an urge to turn something big -- something I've not been able to turn on a mini lathe. This rough turned bowl is walnut from a fellow member of the local woodturning club. The wood is wet but I had sealed it with wax emulsion to preserve it so there don't appear to be any bad cracks. I'll rough turn it, leaving it oversized, then soak it in alcohol to try to dry it faster without checking. Once I can dry it, I'll finish turn it to final size and finish. The bowl finished out at 11 inches diameter and 4 inches high. Enter your email at http://www.AsWoodTurns.com & I'll let you know when the next easy woodturning project video is ready. Web: http://www.AsWoodTurns.com FB: http://www.Facebook.com/ AsWoodTurns

Better view of rough turning
By: Russ Barber
April 18, 2014 · 120 views

In this video I slow down my movements so everyone can see what I'm doing going from the pull cut into the push cut. Some movements are more than needed, I done these on purpose to give a better view of them.

Woodturning-Roughing a natural edge bowl
By: Amy Grigg
April 09, 2014 · 255 views

via YouTube Capture

ROUGHING CUTS by Reed Gray aka Robo Hippy
By: robohippy
April 08, 2014 · 2,302 views

Rough turning the inside
By: Russ Barber
March 31, 2014 · 29 views

Part 2 roughing out the inside of the unknown Oak bowl

Rough turning the outside
By: Russ Barber
March 31, 2014 · 27 views

Rough turning the outside of a 9' unknown Oak bowl part 1

Outrigger Tuning on a Nova 3000
By: J.B Wood Turning
March 18, 2014 · 12,544 views

In this tutorial you will learn my techniques to outrigger turning on my Nova 3000

Roughing with my woodturning tool in slo-mo
By: SegmentedTurner
January 25, 2014 · 1,926 views

Here's an interesting demonstration of my woodturning tool being used to do some exterior roughing on a piece of spalted willow. The slow motion video lets you see how the chips leave the bit and also shows how little chucking you get on an interrupted cut.

#18 Bowls from Logs Part 2 Roughing and Boiling Green Bowls
By: Stephen Ogle
January 10, 2014 · 74,226 views

This video picks up after cutting and sealing blanks from a log and includes my methods for roughing and boiling to help stabilize the rough turning.

Remounting a Walnut Bowl rough out, turning and finishing the bowl.
By: Turning Round
January 05, 2014 · 1,643 views

Taking a dry bowl blanks which is warped and rough and remounting it and putting it on the wood lathe to finish it.

Ebauche d'un bol en Ã rable - Roughing a bowl maple
By: Laurent Cortot
December 23, 2013 · 1,621 views

Ébauche d'un bol de 28 cm de diamètre pour 20 cm de haut et 2,5 d'épaisseur. Draft a bowl 28 cm diameter 20 cm high and 2.5 thick. Mon blog: http://lolotourneur.blogspot.com/ Ma page facebook: https://www.facebook.com/pages/Lolo-tourneur/350100615098949?notif_t page_new_likes

Roughing out a Bowl Blank on wood Lathe
By: Turning Round
September 27, 2013 · 2,519 views

This video show the first steps for setting up and roughing out the outside of a bowl. I am turning a big Ash Tree blanks into a rough and round blow.

Woodturning - Time Lapse - Roughing out an Ash Bowl
By: Kim Gowney
August 07, 2013 · 600 views

This was just an experiment with a time lapse app on a phone camera, don't expect to learn anything from it. I wish I could knock them out this quick! link to the app page: http://www.lapseit.com

Doo Doo Doo Turning in my Backyard
By: Bob Hamilton
July 15, 2013 · 3,424 views

Just finish turning a dried roughed out bowl on my small lathe in the backyard.

WeekendTurner: Time lapse bowl roughing
By: weekendturner.com
July 12, 2013 · 859 views

Just a quick hit testing out a new time-lapse phone app. I was rough-turning a 15' log blank from a recently felled 100-year-old Pecan tree. Took it to the workshop at NC State CraftCenter and used their lathe to get this natural-edge bowl to about 1' thickness for drying. Process took about an hour, mainly due to difficulties getting the 45-lb wet blank balanced enough to turn at a decent speed. App took a photo every 2 seconds, and I rendered it at 15 FPS so the whole thing runs in about 2 minutes of video. Sorry in advance for the poor lighting and image quality. It was an experiment. I wasn't expecting much but it actually came out better than I expected so I took liberty of posting here.

Rough Turning Elm Bowls
By: Steve Lindsley
June 26, 2013 · 9,901 views

My co-worker Scott cut down an elm tree and was kind enough to give me a couple of the pieces. I don't turn much green wood and do less with the chain saw and it shows in the video. Overall, it was fun but it was a lot of work. Hopefully once they dry I can turn them into some nice bowls.

Tournage sur bois: Ã bauche d'un grand bol - Roughing a large bowl
By: Laurent Cortot
June 25, 2013 · 14,339 views

Mon blog: http://lolotourneur.blogspot.com/ Ma page facebook: https://www.facebook.com/pages/Lolo-tourneur/350100615098949?notif_t page_new_likes Tournage de l'ébauche d'un grand bol en frêne vert, il ne reste plus qu'a attendre que le bol soit sec et déformé pour le reprendre.

rough hollowing a bowl
By: Al Hockenbery
April 23, 2013 · 3,163 views

clip from a demo on gouges given at tri-country woodturners. In this clip I hollow a live oak bowl. Sound is not picked up real well. excellent Video by Jan!

Lyle on Rough Turning a Bowl
By: Lyle Jamieson
October 03, 2012 · 219,547 views

Lyle Jamieson demonstrates taking a square bowl blank and turning it round. He uses a push cut with a bowl gouge with ease. It is a finesse thing, not a strength thing.

Lyle on Roughing a Hollow Form
By: Lyle Jamieson
October 03, 2012 · 2,348 views

Lyle Jamieson demonstrates turning a square blank into a round. He stresses the difference between a spindle roughing gouge use and a bowl gouge use for roughing out spindle oriented grain.

Roughing out a Green Bowl Part 4
By: Woodturners of Southwest Missouri
June 24, 2012 · 947 views

Dr. Ernie Lorenc roughs out a green bowl for the Woodturners of Southwest Missouri. A chapter of the AAW in the Springfield, MO area. www.woodturnersofswmo.org

Roughing out a Green Bowl part 3
By: Woodturners of Southwest Missouri
June 24, 2012 · 1,098 views

Dr. Ernie Lorenc roughs out a green bowl for the Woodturners of Southwest Missouri. A chapter of the AAW in the Springfield, MO area. www.woodturnersofswmo.org

Roughing out a Green Bowl part 2
By: Woodturners of Southwest Missouri
June 23, 2012 · 1,292 views

Dr. Ernie Lorenc roughs out a green bowl for the Woodturners of Southwest Missouri. A chapter of the AAW in the Springfield, MO area. www.woodturnersofswmo.org

Roughing out a Green bowl Part 1
By: Woodturners of Southwest Missouri
June 23, 2012 · 1,195 views

Dr. Ernie Lorenc roughs out a green bowl for the Woodturners of Southwest Missouri. A chapter of the AAW in the Springfield, MO area. www.woodturnersofswmo.org

Rough Turning Silver Maple Bowl â ” Raw Footage
By: Jake Gevorgian
April 26, 2012 · 3,880 views

Presentation is sponsored by Palo Arte Woodworks in Los Angeles - http://www.paloarte.com - - - - - ----- - - - - - ----- - - - - - ----- - - - - - ----- - - - - -

Completing a Rough-Turned Bowl on the Wood Lathe
By: WYOMINGWOODTURNER
March 30, 2012 · 15,245 views

Sam turns a rough turned-- dry bowl blank. This demonstration shows each step in the process of turning a bowl with instruction on understanding the bowl gouge.

Woodturn and Microwave Dry Rough Bowl
By: As Wood Turns
March 19, 2012 · 11,879 views

http://www.AsWoodTurns.com For Woodturning this bowl, I'm starting with Apricot harvested recently. The wood blank is still very green or wet. I will microwave this bowl to see if the microwave will speed up the process and profit some 'instant gratification'. Alas, no luck with this wood turning project. Microwave drying even at 20% power produced disappointing checks and cracks in the bowl blank. To add insult to injury, the microwave only reduced moisture content by about 11%. There's too much moisture left to risk finish turning this bowl. So, I'll relegate it to the paper sack and let it season as I should have in the first place. I'll finish it in a couple of months and see what can be salvaged. Patience does have its place when working with green wood. Give me your email at http://www.AsWoodTurns.com & I'll let you know with the next woodturning project video is ready. http://www.AsWoodTurns.com

Rough Turning Bowls For Turning - High Speed Production
By: Getting0Done
March 16, 2012 · 4,493 views

With my new lathe being ready and working good, its time to rough turn some pieces so in a couple months they will be dry and ready to re-turn into finished pieces. They are all pear from a previous video except the last one is a piece of maple.

Turning maple vase 1 Roughing
By: Nakajima Shintaro
January 29, 2012 · 875 views

Birds-eye maple log on Robust AB25.

Roughing bowls part 3 of 3
By: Bob Hamilton
January 25, 2012 · 43,471 views

This is the third part of three of a video showing how I cut a log into bowl blanks and roughed them out into rough bowls ready for drying.

Roughing bowls part 2 of 3
By: Bob Hamilton
January 25, 2012 · 52,766 views

This is the second part of three of a video showing how I cut a log into bowl blanks and roughed them out into rough bowls ready for drying.

Roughing bowls part 1 of 3
By: Bob Hamilton
January 25, 2012 · 129,709 views

This is the first segment of three of a video about how I cut a log into bowl blanks and roughed them out into rough bowls ready for drying.

Timelapse - Rough turning a 20 pecan bowl
By: Chas Thornhill
January 16, 2012 · 16,770 views

Preparing a pecan crotch for the lathe and rough turning a bowl 20' in diameter. This video was made using the timelapse feature on my Samsung HD camcorder.

Roughing Gouge Alternative
By: john60lucas
January 14, 2012 · 43,924 views

This video is to show how to use a bowl gouge or spindle gouge to rough out or round out a platter or bowl. A roughing gouge is dangerous for this operation.

テスト動画 'ホワイトオークのブランク' IMG_0342.MOV
By: Nakajima Shintaro
January 02, 2012 · 583 views

ウッドターニングに関する動画upテスト。ラフィング、コアリング前の様子。

Hollow form Roughing part 2
By: Mark Sanger
December 09, 2011 · 34,422 views

Mark Sanger roughs a hollow form Part 2

Coring backwards4: Rough turning the bowl
By: Bob Hamilton
September 27, 2011 · 5,668 views

This is the fourth segment of six of a companion video for my article 'Coring backwards' about constructing a bowl blank from rings parted from a board on the lathe.

Roughing out an 8' bowl
By: Solway Wood Turning
September 19, 2011 · 592 views

8' wet beech wood bowl, hollowed using a fingernail ground 3/4' bowl gouge on a record CL4 www.solwaywoodturning,co.uk

Roughing a curly maple bowl with my tool
By: SegmentedTurner
August 01, 2011 · 2,573 views

Here's a fresh video showing the use of my tool for quick roughing of a curly maple blank with a large void on one side.

Glenn Lucas - Rough Shaping a salad bowl
By: Glenn Lucas
May 03, 2011 · 12,702 views

DVDs available from http://glennlucas.com/dvds

Roughing Down
By: WoodturningFYP2011
April 08, 2011 · 478 views

Roughing Down a spindle on a wood lathe

Turning Down to Round
By: WoodturningFYP2011
March 20, 2011 · 851 views

Turning a square Workpiece down to round

Rapid roughing with my woodturning tool
By: SegmentedTurner
January 14, 2010 · 79,271 views

In this video I quickly turn a rough piece of Black Locust to a bowl shape using my own design woodturning tool. I sell these on Etsy.com and on my web site at http://WWW.DWMontville.com. You can buy complete tools or just the hardware to make your own handle for. They come in two sizes, standard using a 1/4 inch square bit, or micro using a 1/8 inch square bit. I also sell a sharpening block to make it easy to sharpen or shape the bit end on a conventional grinder.

True Economy 6 - Roughing the inside
By: Bob Hamilton
September 30, 2009 · 193,682 views

This is segment #6 of 9 of a companion video for my article on turning a bowl from a board. The illustrated article as well as other articles are located on my website at: http://bobhamswwing.com/index_of_articles.htm

Cindy Drozda Woodturning Lesson - Roughing a Finial Blank
By: Cindy Drozda
August 22, 2009 · 43,567 views

An excerpt from my DVD 'Finial Star', showing how I turn a square Finial blank round and mount it into a chuck. Please visit my website, http://www.cindydrozda.com for more information about me, my Artwork and Woodturning Instruction. Instructional Woodturning DVDs, Signature Woodturning Tools, Supplies and Accessories for Woodturning are now available for online ordering! Questions and Comments are invited.

My tool turning rough Box Elder
By: SegmentedTurner
June 16, 2009 · 5,208 views

Here's a presentation showing how my woodturning tool works on a 'not quite round' piece of box elder. This piece became 'Norwestr', which I show in later videos being colored. This piece is now gone to a new owner, but if you're interested in other pieces or would like to commission a piece from me, please visit my web site at http://www.DWMontville.com.

Grinding knots on the lathe
By: Don Kleinschnitz Jr.
April 24, 2008 · 14,130 views

WEAR HAND AND EYE PROTECTION AND BE CAREFULL! Lots of turners use their chainsaws to trim large wood on the lathe. I'm not convinced that chainsaws and lathes are compatible I think this is a better way to trim logs on the lathe than using your chain saw. I had been looking at this chainsaw blade attachment for an angle grinder for some time. It is a bit expensive but worth it. More woodturning at www.turnedoutright.com The wood is wet Aspen.

tournage
By: tournar
April 01, 2008 · 1,215 views

dégrossir

Roughing a Bowl (8) the inside part b
By: Darrell Feltmate
December 04, 2007 · 21,460 views

I have cut the inside roughing video in two to fit better on YouTube for real time. Here is the second part. http://www.aroundthewoods.com/roughing02.shtml

Roughing a Bowl (7) the inside part a
By: Darrell Feltmate
December 03, 2007 · 26,266 views

I have cut the inside roughing video in two to fit better on YouTube for real time. It pretty much breaks down into hollowing and then removing. http://www.aroundthewoods.com/roughing02.shtml

Roughing a Bowl (6) the outside
By: Darrell Feltmate
November 29, 2007 · 21,571 views

Rough turning the outside of the bowl with a shop made 3/8' Oland tool. http://www.aroundthewoods.com/001page01.html In order to fit YouTube I had to shorten the video by 70 seconds so it gives a good indication of the time needed to rough the outside of the bowl.

Roughing a Bowl (5) Mounting on the Lathe
By: Darrell Feltmate
November 27, 2007 · 18,096 views

mounting the bowl blank between centers on the lathe. http://aroundthewoods.com

Roughing a Bowl (4) Cutting the Corners
By: Darrell Feltmate
November 25, 2007 · 25,360 views

Cutting the corners of the bowl blank with a chainsaw to balance it and fit it on the lathe. http://aroundthewoods.com

Roughing a Bowl (3) Marking Out
By: Darrell Feltmate
November 22, 2007 · 12,029 views

Marking out the blanks using simple home made templates. http://aroundthewoods.com

Roughing a Bowl (2) Ripping the Blanks
By: Darrell Feltmate
November 21, 2007 · 24,316 views

Ripping the blanks in two to make 2 bowl blanks per log section. http://aroundthwoods.com

Roughing a Bowl (1) cutting the log to length
By: Darrell Feltmate
November 20, 2007 · 21,817 views

Cutting an ash log to prepare blanks for a bowl. http://aroundthewoods.com

Using a Roughing Gouge
By: Darrell Feltmate
August 09, 2007 · 11,781 views

wood turning a spindle blank to round with a roughing gouge, the basic start to spindle turning http://aroundthewoods.com

Roughing with the Oland Tool
By: Darrell Feltmate
July 20, 2007 · 91,268 views

Using a 1/2' and 3/8' Oland tool to rough down to a bead. http://aroundthewoods.com

Return to Turning Videos

Great Bargains
(ends October 24, 2019)

3M Professional Face Shield

On Sale for only $14.99

Save $3.00

List price: $17.99

Clear, 3/32" thick polycarbonate window provides an unobstructed, non-distorted view. Adjustable suspension headband fits head sizes from 6-1/2 to 8. Tips up and out of the way when not needed.

Click here for more information or to purchase

Rockler Carbide Pen Turning Tools

On Sale for only $109.99

Save $30.00

List Price: $139.99

This three piece set has comfortable rubber handles which provide excellent control and reduce fatigue—replaceable carbide tips require no sharpening.

Click here for more information or to purchase

Bar Tool Turning Kits

Get the 5 Piece Set for only $68.95

Save $15.00

Everything you need to turn out cocktails that friends will rave about—includes all five of their Bar Tool Turning Kits in one cost-saving package. Includes: bottle opener, double jigger, muddler bar, bar spoon, cocktail strainer and 5 threaded inserts.

Click here for more information or to purchase

Dust Right Lathe Dust Collection System

For only $44.99

Save $15.00