Woodturning Online Videos


Welcome to the Woodturning Online Videos page.

This video content was created by woodturner, Rick Morris. He has created a way to monitor all the videos in YouTube that are woodturning related.

Each month, Rick updates the video listings below. If you would like to learn about new videos, sign up for our free newsletter where we will list the top 20 videos each month.

Any categories in BOLD have sub-categories to help you narrow down your search.

Carbide-tipped Videos (85)

Sort by

Or click here to: Search All Videos


Carbide tool set - the parting tool
By: smallathe
March 20, 2019 · 9 views

Making a Parting tool for the lathe - this parting tool is simple yet not fast to make. On the other hand I have made a parting tool by hand - so it's not bad at all to make on your own. Enjoy Saar

 

Carbide tool set - the square tool
By: smallathe
March 16, 2019 · 15 views

Cutting the square tool. If you want to make just one tool for your wood lathe that does not need sharpening and works nicely - that's the one. It is wonderful. It does tend to grab a bit but that is carbide - it will last forever without sharpening! Making it is definitely simple and easy - just like the round one. Thanks for watching. Please like and subscribe Cheers, Saar

 

Carbide tool set - the round tool
By: smallathe
March 16, 2019 · 10 views

The round tool is the simplest tool there is to make - just cut steps into the stainless bar, drill and tap (as you can see) and you are done! This is a very nice tool for the shop and I highly recommend you make one yourself. Bought online these tools are well worth it - but very expensive... Hope you enjoyed Please like and subscribe Cheers, Saar

 

Carbide tool set - the diamond tool
By: smallathe
March 16, 2019 · 14 views

The diamond tool is one of the hardest to make. It required a set of hss endmills. That worked wonderfully though it reqired 0.2mm baby steps to mill the slots. Bottom line this is not the most vital tool but it is nice to have I did not show every bit of the way - that would be too boring... Next up - parting tool, the last tool.

 

Carbide tool set - making the handle
By: smallathe
March 14, 2019 · 33 views

I am making a carbide tool set for wood turning. These tools are very expensive to buy ( 150USD/tool) but very cheap to make (2-3 ). Making these wood turning tools from carbide saves me grinding the tool and I have no worries about the ware and tare on the tool as carbide bits are extremely hard and durable. As for materials and cost: Handle - Brass I already had but it's a tiny piece - 1 should cover it. Wood - you can use any piece of old brancd - I bought mine for 10cents or so Stainless - found it roaming free in a deserted food company site but let's say 10 for a 1foot 30cm piece th

 

Carbide tool set
By: smallathe
March 09, 2019 · 23 views

I'm playing a lot recently with resin - and I also enjoy wood turning - so It's about time to buy a carbide tool set for wood turning, right? Well... these are expensive... too, so, I have decided to make a set! And this is what I got after seven weeks of pure fun! Definitely well worth it - and while I'm sure I'll find bugs and need to address these while 'running' it for the first time - I'm very happy I've made this set. Ah... the cost you ask? Well, a tool ready to use costs around 100 plus 50 shipping. My cost? around 2 for the carbide and the work invested (the stainless I found lying around and the rest was peanuts... :) Hope you like it. Enjoy Saar

 

Hunter Tool Systems Demonstrations: #1 Tapered Hook Tool
By: Hunter Tool Systems
January 08, 2019 · 57 views

http://huntertoolsystems.com

 

Hunter Tool Systems Demonstrations: #1 Osprey Tool
By: Hunter Tool Systems
January 08, 2019 · 103 views

http://huntertoolsystems.com

 

Hunter Tool Systems Demonstrations: #1 Hercules Tool Final
By: Hunter Tool Systems
January 08, 2019 · 65 views

http://huntertoolsystems.com

 

Hunter Tool Systems Demonstrations: #2 Osprey Tool Final
By: Hunter Tool Systems
January 08, 2019 · 136 views

http://huntertoolsystems.com

 

Hunter Tool Systems Demonstrations: #1 Tapered Tool Final
By: Hunter Tool Systems
January 08, 2019 · 30 views

http://huntertoolsystems.com

 

Hunter Tool Systems Demonstrations: #1 Tapered Shoulder Tool
By: Hunter Tool Systems
January 08, 2019 · 28 views

http://huntertoolsystems.com

 

Hunter Tool Systems Demonstrations: #5 Badger Tool
By: Hunter Tool Systems
January 08, 2019 · 75 views

http://huntertoolsystems.com

 

Hunter Tool Systems Demonstrations: #5 Badger Swan Neck Tool Final
By: Hunter Tool Systems
January 08, 2019 · 52 views

http://huntertoolsystems.com

 

Hunter Tool Systems Demonstrations: #3 Hercules Tool
By: Hunter Tool Systems
January 08, 2019 · 65 views

http://huntertoolsystems.com

 

Hunter Tool Systems Demonstrations: Hunter Viceroy Tool
By: Hunter Tool Systems
January 08, 2019 · 79 views

http://huntertoolsystems.com

 

Hunter Tool Systems Demonstrations: The Adjuster Tool
By: Hunter Tool Systems
January 08, 2019 · 78 views

http://huntertoolsystems.com

 

carbide turning tool on a round shaft
By: earl's small segment shop
January 05, 2019 · 682 views

Putting a carbide bit on a round shaft

 

Tool review Carbide cutter assembly
By: Lyle Jamieson
April 18, 2018 · 1,116 views

Tool review of The Jamieson/Hunter carbide assembly. This is set up to slice wood fibers not used as a scraper. The surface left behind from this tool is amazing. Please see my website for all the resources and tool store. Every tool listed has more information details. See not only the right tools but tips and techniques on how to use them. I have archived my articles written for publications and each of my newsletter broadcasts have all the Q&As listed by topic and indexed table of contents. Don't forget to subscribe here for the YouTube videos. Please support my sponsors Mike Hunter tools and Doug Thompson tools. https://lylejamieson.com

 

Woodturning with a carbide router bit
By: Scary Catches
April 04, 2018 · 95 views

Testing a regrinded router bit in almost dry birch

 

WOODTURNING -CARBIDE CUTTING TOOLS! #WW41
By: Nick Zammeti
January 10, 2018 · 10,787 views

Here are my own carbide cutting tools for woodturning. there are branded NZ Woodturning and have my logo on the bottom also. MAKERS CENTRAL WEBSITE http://www.makerscentral.co.uk/ MAKERS CENTRAL INSTAGRAM https://www.instagram.com/makerscentral/?hl en MAKERS CENTRAL FACEBOOK https://www.facebook.com/makerscentral/ MY WEBSITE http://www.nzwoodturning.co.uk/ CHARLIE THE MAKER (My little boys channel) https://www.youtube.com/channel/UClU3oIHFJwi4_UF-l_Lc7cw THE RESIN I USE IS FROM HERE http://www.ebay.co.uk/usr/aktiniumltd http://www.resin4art.com/ YORKSIRE GRIT http://yorkshire-grit.c

 

An introduction and Review(of sorts) of my new BlackLine carbide wood turning tools
By: Chad Schimmel
January 08, 2018 · 3,973 views

In this video I talk about my new turning tools the Blackline Midi Carbide set. I have really grown attached to these tools and the quality is amazing. If you are interested in these tools please contact Tim Cost at Local Woodwork. He will give you all the info and help in picking out your set. THE DISCOUNT CODE Mentioned in this video has Expired. https://shop.localwoodwork.com/t/blackline-tool-sets Tim is also a Nova tools dealer I just found out so he can help you with those also. For pen making and wood turning supplies please check out Turners Warehouse at www.turnerswarehou

 

Video 1 HSS vs Carbide to flatten bowl bottom
By: J.B Wood Turning
January 02, 2018 · 217 views

A video to show the use of a 1/2' high speed steel scraper, and same size carbide to flatten a bowl bottom.

 

Sharpening Carbide Cutters - Quick Tip
By: Gord Rock
September 15, 2017 · 2,771 views

A quick, easy way to sharpen those carbide cutters that the manufacturers want you to believe cannot be sharpened. Thanks to Dick for turning on the light!!!

 

Unboxing 6 Simple Woodturning Carbide lathe tools
By: AtkinsonWoodturning Beast
March 20, 2017 · 1,937 views

This is a basic un-boxing video of the Carbide Simple Woodtools set of 6. I wanted to show them to those of you who are considering buying them. I am happy with how well they work and I will shoot another video of how to use them later. _ _ _ _ _ _ _ _ _ _ I want to upload a new project video every month (if at all possible – I am a stay at home Dad and my little boys rule my time). Thank you for supporting me in this endeavor. Please share your thoughts on my projects because I love to learn from others perspectives. If you are interested in my work, you can own o

 

Carbide Simple Parting Tool Woodturning lathe demonstration
By: Kerry Harrison
October 04, 2016 · 4,656 views

The worlds 1st carbide tipped parting tool for woodturning with a brazed carbide tip! The tip can be resharpened and blade is replaceable. http://www.harrisonspecialties.com/carbide-simple-parting-and-grooving-tool-for-woodturning-lathe

 

Product Spotlight - The Easy Detailer From Easy Wood Tools
By: Le PicBois
September 12, 2016 · 2,538 views

[The diamond shaped cutters on the Easy Detailers are designed for putting the final touch on your project such as small beads and coves. This cutter can also be used for roughing, finishing and cutting chuck tenons.] Support me on Patreon: https://www.patreon.com/lepicbois Website: http://lepicbois.net/ YouTube: https://www.youtube.com/lepicbois Facebook: https://www.facebook.com/AtelierLePicBois Instagram: http://instagram.com/atelierlepicbois Twitter: https://twitter.com/atelierpicbois Special Thanks: Easy Wood Tools: https://www.youtube.com/user/EasyWoodTools ___________________________________________________________ If you wish we work together, drop me a line: http://lepicbois.net/contact

 

A Quick Look at Carbide Burrs and Discs - Tom Turns - Review
By: Tom Stratton
April 21, 2016 · 8,168 views

Following on from my previous video on the Three Footed Bowl, Tom takes a quick look at carbide burrs and discs for rotary tools and min-grinders. I use the Proxxon Long Neck grinder and the Dremel 4000 series rotary tool along with carbide tips and disks from SaburrTooth, Duragrit and King Arthur's Tools. A further review, and details / links can be found at: http://tomturns.com. I have no connection with any company mentioned and am not sponsored or supported in any way by them. I do not endorse these products, simply show you what I have used. Any trade names mentioned are the property of the copyright holder and are used here for demonstration purposes only!

 

Pear Box from Walnut - Trying out my Carbide Woodturning Tools
By: Jake Webb
August 17, 2015 · 4,008 views

My first full project using my my homemade Carbide Cutters. For my video on making these tools please click here https://www.youtube.com/watch?v HQTS_RbbaF0. My Website: http://www.jwwoodturning.co.uk Folksy page: https://folksy.com/shops/JWWoodturning Music: http://www.purple-planet.com

 

Failure to improve - Carbide Woodturning Tool follow up
By: Jake Webb
July 30, 2015 · 10,967 views

Trying to improve on my last design and failed. Please post any suggestions on the YouTube comments so anyone watching can follow the discussion. My Website: http://www.jwwoodturning.co.uk Folksy page: https://folksy.com/shops/JWWoodturning Music: http://www.purple-planet.com

 

Making my own Carbide Woodturning Tool
By: Jake Webb
July 27, 2015 · 47,600 views

My first attempt at making my own carbide woodturning tool. It was one of those days when everything seemed to fight back, but I got there in the end. Some lessons learn't and I'm happy with the result. A Square peg in a round hole does go. Follow up video: https://www.youtube.com/watch?v HQTS_RbbaF0 My Website: http://www.jwwoodturning.co.uk Folksy page: https://folksy.com/shops/JWWoodturning Music: http://www.purple-planet.com

 

Making my own Woodturning Tools
By: Jake Webb
July 15, 2015 · 13,516 views

Video inspired by WoodChuckers posting and discussion https://www.facebook.com/groups/harri.woodchuckers Chuck tool video Robbiethewoodturner https://www.youtube.com/watch?v ABijDmKrJXs Allen key tool WYOMINGWOODTURNER https://www.youtube.com/watch?v bUqtrYfOxwM Turning tool handles The Wood Whisperer https://www.youtube.com/watch?v NIGe5DtKlFc My Website: http://www.jwwoodturning.co.uk Folksy page: https://folksy.com/shops/JWWoodturning Music: http://www.purple-planet.com

 

Le PicBois - Here is why I like Easy Wood Tools!
By: Le PicBois
May 13, 2015 · 1,269 views

Trying the 'Easy Finisher' on a hard maple piece... Full video here: https://www.youtube.com/watch?v qe34C_WivrI Support me on Patreon: https://www.patreon.com/lepicbois Website: http://lepicbois.net/ YouTube: https://www.youtube.com/lepicbois Facebook: https://www.facebook.com/AtelierLePicBois Instagram: http://instagram.com/atelierlepicbois Twitter: https://twitter.com/atelierpicbois ________________________________________________________ Special Thanks: Easy Wood Tools: https://www.youtube.com/user/EasyWoodTools Carl Jacobson: https://www.youtube.com/user/haydenHD ______________________

 

Carbide tools--on the level
By: Ed Brown
March 15, 2015 · 3,139 views

How to turn with Easy Wood Carbide Tools. Ed shows the level and how to turn dense blanks.

 

Carbide tool1
By: Ed Brown
March 15, 2015 · 1,448 views

Description

 

#15 Dark Birch Bowl & Carbide Tools for Beginners - Wood Turning - Acolyte Turner
By: Tom Stratton
November 26, 2014 · 21,057 views

In this video I review a set of carbide turning tools from Glen Teagle at http://www.ukwoodcraftandcarbidechisels.co.uk/ whilst turning a bowl from a piece of Dark Birch. Mike Waldt's video can be seen here: www.youtube.com/watch?v PD5lf7S_YFY Further projects, turnings and information can be found at http://tomturns.com CHANNEL TAGS Acolyte Turner, Wood Turning, Turning, Project, Ossett, West Yorkshire, UK, Nova, Record Power, DVR XP, BS350, Lathe, Bandsaw, Sanding, Sandpaper, Ruth Niles, Off Centre Jig, Off Center Jig, help, tips, training, learning, how to, Hollow Form Elm Pot Pourri Pot Pourri Holder Carbide Carbide Tools Carbide Turning Tools RS200KT Glen Teagle

 

Woodturning model of the Seattle Space Needle using carbide tools
By: SJWoodworks
November 26, 2014 · 3,069 views

My wife's friend Randi asked me to make a model of the Seattle Space Needle. Sounded like a fun spindle project, so here we go! See Randi's blog here: http://www.sowderingabout.com/ Photo credits: Space Needle - photo by Jordon Kalilich, Stratosphere Las Vegas - photo by Tim Jarrett Photos used under Creative Commons lincense 'CC BY-SA 3.0' http://creativecommons.org/licenses/by-sa/3.0

 

Woodturning a family portrait using carbide lathe tools
By: SJWoodworks
November 17, 2014 · 3,713 views

I used a few branches off a dead tree in my back yard to make some peg people, representing my family. The wood is soft, crumbly, and terrible for turning, in spite of having some interesting colors and a bit of spalting here and there. But seriously, torn out grain everywhere, and no way to really get a good surface. Now I just need to figure out how to make the dog. Simple danish oil to finish it up here. Remember, wood working is dangerous, and this video is for entertainment only, not a demonstration of proper or safe technique. You are responsible for your own safety in your shop.

 

Woodturning claro walnut bowl using carbide tools
By: SJWoodworks
October 30, 2014 · 7,028 views

My 8 year old daughter is wiser than I at times, I'm afraid. In this quick video, I turn a 6.5' claro walnut footed bowl using carbide lathe tools. Worth every second to watch this one, guaranteed. Please 'like' and subscribe to my channel. Any comments also appreciated!

 

Woodturning large spinning top using carbide lathe tools
By: SJWoodworks
October 09, 2014 · 13,972 views

This is a jumbo spinning top from an oak dowel and an unknown chunk of wood. I saw Chris Pine do this over a year ago, and I finally got my own done. See his video here: https://www.youtube.com/watch?v CHrxozwLJ_I Please comment, like, and subscribe!

 

Woodturning: Carob wood bowl with carbide lathe tools
By: SJWoodworks
September 24, 2014 · 4,025 views

In this one, I turn a cereal bowl from carob wood using carbide lathe tools. Carob wood is one of my favorite things. There are colors and patterns hidden in there you just don't expect to find. Finish is a simple home made friction polish.

 

Part 3 of 3 - Woodturning: Can I do it with carbide
By: SJWoodworks
September 10, 2014 · 38,460 views

Part 3 of a 3 part video. Turning a simple bowl with carbide tools, facegrain hollowing. This is one long video, broken up into three parts. I go through many basic cuts and operations of woodturning and demonstrate how to do them with carbide tools. I confess I’m not an expert at everything shown here – my beads could use some work, that’s for sure! But in the end, I get it done, I think. Part 1: http://youtu.be/k0ismyEFLCI Part 2: http://youtu.be/cmaUUSUQw4E Part 3: http://youtu.be/ZQELtpCBdVU Here are the makers of the carbide tools I use: Harrison Specialties: http://www.harrisonspeci

 

Part 2 of 3 - Woodturning: Can I do it with carbide
By: SJWoodworks
September 10, 2014 · 37,429 views

Part 2 of a 3 part video. Turning a goblet in purple heart with carbide tools, with end grain hollowing. This is one long video, broken up into three parts. I go through many basic cuts and operations of woodturning and demonstrate how to do them with carbide tools. I confess I’m not an expert at everything shown here – my beads could use some work, that’s for sure! But in the end, I get it done, I think. Part 1: http://youtu.be/k0ismyEFLCI Part 2: http://youtu.be/cmaUUSUQw4E Part 3: http://youtu.be/ZQELtpCBdVU Here are the makers of the carbide tools I use: Harrison Specialties: http://w

 

Part 1 of 3 - Woodturning: Can I do it with carbide
By: SJWoodworks
September 10, 2014 · 49,164 views

Part 1 of a 3 part video. Introduction to carbide tools, and spindle turning. This is one long video, broken up into three parts. I go through many basic cuts and operations of woodturning and demonstrate how to do them with carbide tools. I confess I’m not an expert at everything shown here – my beads could use some work, that’s for sure! But in the end, I get it done, I think. Part 1: http://youtu.be/k0ismyEFLCI Part 2: http://youtu.be/cmaUUSUQw4E Part 3: http://youtu.be/ZQELtpCBdVU Here are the makers of the carbide tools I use: Harrison Specialties: http://www.harrisonspecialties.com

 

Carbide Barrel Trimmer Review and Desctruction
By: Turning Round
September 08, 2014 · 1,903 views

This is a new Carbide tipped barrel trimmer for squaring the blanks of a Custom Pen. This is used before putting it on the lathe and turning it. In this video I get a new trimmer and shows it use. the second blank I try to trim I manage to bend the shaft of the Barrel trimmer and so the video is a review and bit of a blooper real.

 

Woodturning a lathe tool handle using carbide tools
By: SJWoodworks
September 03, 2014 · 16,881 views

In which I turn a tool handle FOR a carbide tool, USING carbide tools.

 

Woodturning Cherry Cookie Plate using carbide tools
By: SJWoodworks
August 27, 2014 · 2,644 views

Using carbide lathe tools, I turn a cherry plate, perfect size for serving up some cookes.

 

Woodturning a large dogwood bowl using carbide lathe tools
By: SJWoodworks
August 20, 2014 · 21,849 views

This week's video is just a few minutes longer than my normal videos. I tried to be quite instructional here on the use of various carbide tools in turning a fairly large bowl - about 10' x 3'. Please comment with any questions or observations!

 

Woodturning a wooden apple with carbide lathe tools
By: SJWoodworks
August 14, 2014 · 27,420 views

This week, I'm responding to a challenge issued by Steve Ramsey of Woodworking for Mere Mortals (I'm a MeMo!), and Alex Harris from ThisWoodWork to represent my home state with a woodworking project. Since I'm from the state of Washington, where we grow a lot of apples, I decided to turn an apple on the lathe. It's a Red Delicious apple (the iconic Washington apple) made from bloodwood, using only carbide lathe tools to make it. Steve Ramsey's challenge video: https://www.youtube.com/watch?v sDJ1yXhmwuM Alex Harris's challenge video: https://www.youtube.com/watch?v B_GbYnXHS3U While I'm sure you already subscribe to both of these fantastic woodworkers on youtube, if you don't, do it! They are both entertaining and informative. I loved the challenge!

 

Woodturning a wooden live center with carbide lathe tools
By: SJWoodworks
August 06, 2014 · 26,275 views

I'll turn a useful threaded maple live center cover using carbide lathe tools. This way, I can apply tailstock pressure to a piece when necessary without piercing it with the point of either the cone or cup of my live center. Next week, I'll be just coming off vacation, so I'll put up a short video showing a simple alternative to this fancy wooden live center.

 

Woodturning ambrosia maple form with carbide tools and disaster
By: SJWoodworks
July 17, 2014 · 15,655 views

Woodturning ambrosia maple open form using carbide lathe tools. Spoiler - this turning doesn't quite make it to completion, but who hasn't had a disaster at the lathe? It's what we learn from the experience that counts!

 

Woodturning a claro walnut trumpet bowl with carbide tools
By: SJWoodworks
July 10, 2014 · 3,922 views

In this video we turn a claro walnut trumpet-shaped bowl on the lathe with carbide tools. I got the recipe for my friction polish finish from The Naked Turner: http://www.youtube.com/KireOgerNosredna

 

Woodturning small bowl from lemonwood with carbide tools
By: SJWoodworks
July 03, 2014 · 24,790 views

Let's turn a small coin or key bowl from lemonwood using carbide tools. If you like this video, please subscribe! I've got lots more ideas coming. My tools came from here: http://www.harrisonspecialties.com/wood-turning-accessories/ I am not sponsored by this toolmaker, I just have some of the stuff they offer, and like it.

 

Woodturning - cocobolo pen with carbide tools
By: SJWoodworks
June 29, 2014 · 23,937 views

Woodturning - Using carbide lathe tools to turn a cigar-style twist pen. Carbide pen-turning tool from: http://www.harrisonspecialties.com/wood-turning-accessories/ Pen kit from: http://www.woodturnerscatalog.com

 

# 216 the Care and Feeding of Carbides
By: Cap'n Eddie Castelin
February 26, 2014 · 80,132 views

A primer on carbide tools, set-up, handles, etc.Big Guy Productions and Capt. Eddie Castelin are at it again. Contact Cap'n Eddie at eddiecastelin@cox.net or www.eddiecastelin.com

 

Wood Turning - Carbide Tools Review
By: Mike Waldt
January 19, 2014 · 46,909 views

I review several Carbide Tools made by Glenn Teagle : http://www.ukwoodcraftandcarbidechisels.co.uk/ http://www.ebay.co.uk/sch/733gtfly/m.html?item 271377388438&pt UK_Crafts_Other_Crafts_EH&hash item3f2f5a5396&rt nc&_trksid p2047675.l2562 Visit Glenn's website or eBay shop to see the full range of Carbide Tools he offers.

 

Hope Woodturning 8mm Carbide Tool
By: Simon Hope
January 06, 2014 · 15,906 views

How to use the 8mm Hope Carbide Tool

 

Hope Woodturning 6mm Pro Carbide
By: Simon Hope
January 06, 2014 · 7,871 views

How to use the Hope Woodturning 6mm Carbide Pro Tool

 

Woodturning Q&A Easy Wood Tools Carbide Cutter
By: The Woodshop
April 16, 2013 · 20,235 views

In this video I demonstrate the Easy Wood Tool. Ways you can support the show Schedule one-on-one online classes jacobson68@yahoo.com ChefwareKits http://www.chefwarekits.com/easy-wood-tools?tracking carleasy Easy Wood Tools http://www.easywoodtools.com/ Website http://www.thewoodshop.tv/ Google https://plus.google.com/113199904565893027390#113199904565893027390/posts Facebook https://www.facebook.com/pages/The-WoodshopTV/161892940583516?ref hl Welcome to my channel, I have a new project video every Friday with wood turning tips and projects. Taking you from start to finish with a ruff piece of wood to your sanded and finished project.

 

105 New Radius Squared Cutter
By: Cap'n Eddie Castelin
November 07, 2011 · 18,377 views

I found a new carbide cutter for an outstanding price.

 

Wiedemann Schaber - Drechsler drechseln
By: WiedemannHeinz
May 17, 2011 · 11,003 views

Weitere Infos finden sie unter http://www.holz-im-design.de Hier kommt der Wiedemann Schaber zum Einsatz.

 

Easy Finisher final passes
By: Christine Caliendo
May 04, 2011 · 18,012 views

Tips for getting the best possible surface with your Easy Finisher Check out Easy Wood Tools' website at: http://easywoodtools.com/store.php or call us direct at 859-246-0294. We also have many retail stores that carry our products, see this link for full list: http://easywoodtools.com/links.php Safety Disclaimer: Easy Wood Tools strives to offer the safest wooturning tools on the market, but you still must follow reasonable safety considerations. Our company recommends the use of full safety equipment when turning wood. Project safety is your responsibility; so please read

 

Parting off with the Easy Detailer!
By: Christine Caliendo
March 17, 2011 · 35,357 views

Parting off is now no big deal. Just one more way to use your Easy Wood Tools.

 

Easy Hollower 3-16-11
By: Christine Caliendo
March 16, 2011 · 14,254 views

New Video on the Easy Hollower Wow! What a tool! I am blown away every time I use this new tool. It is so easy to use I cannot imagine hollowing with anything else.

 

Hunter carbide back cutting tools
By: john60lucas
October 19, 2010 · 6,518 views

This video shows how I use 2 of the Hunter back cutting tools for cleaning up the sides of vases and straight sided vessels.

 

Hunter Carbide taper hollowing tools
By: john60lucas
October 19, 2010 · 15,454 views

This is about hollowing with the Hunter #1 taper hollowing tools. I try to show how I use the tools and the progression for hollowing.

 

Hunter carbide turning tool
By: john60lucas
October 19, 2010 · 44,031 views

This is how I use the hunter carbide tools to achieve a superior finish

 

SRB Carbide Woodturning Tools
By: woodturningtools
June 25, 2010 · 6,753 views

 

S12 Carbide Woodturning Tools
By: woodturningtools
June 25, 2010 · 5,742 views

 

SR Carbide Woodturning Tools
By: woodturningtools
June 25, 2010 · 4,018 views

 

Brand New Carbide Wood Turning Tools
By: woodturningtools
June 23, 2010 · 47,597 views

Carbide WoodTurning Tools has developed 3 NEW SERIES of carbide wood turning tools (5 lines of tools in all now) which will eliminate much of the difficulty of roughing out, hollowing, and finishing wood blanks. World's largest and best selection of carbide wood turning tools. http://www.carbidewoodturningtools.com

 

Easy Wood Tools - Mini Series Tools Up Close
By: Christine Caliendo
April 13, 2010 · 8,159 views

Craig Jackson of Easy Wood Tools shows some quick cuts using the Mini Series tools: Ci2m Mini Rougher, Ci3m Mini Finisher, and the Ci4m Mini Detailer.. Wood: Kiln Dried Maple

 

Easy Wood Tools Mini Series Tools
By: Christine Caliendo
April 13, 2010 · 27,836 views

Craig Jackson of Easy Wood Tools shows some quick cuts using the Mini Series tools: Ci2m Mini Rougher, Ci3m Mini Finisher, and the Ci4m Mini Detailer. Wood: Kiln Dried Maple

 

Easy Wood Tools - Spaled Maple Burl #5 - How to get the best possible finish
By: Christine Caliendo
February 14, 2010 · 9,998 views

Now that your blank is round, let's look at how to get the best possible surface. Slow down feed rate to get a better finish cut Do you use the corner or nose of the cutter? See our website for more information on the tools used in this video www.easywoodtools.com or call 270-903-4270. Our tools are proudly made in the USA and our shop is located in Owensboro, Kentucky.

 

Easy Wood Tools - Spalted Maple Burl #4 -Round up a maple blank with Craig Jackson
By: Christine Caliendo
February 14, 2010 · 7,470 views

Getting it Round # 4 Craig finishes up rounding up his maple spalted burl blank. He'll now be ready to work on shaping the bowl. See our website for more information on the tools used in this video www.easywoodtools.com or call 270-903-4270. Our tools are proudly made in the USA and our shop is located in Owensboro, Kentucky.

 

Easy Wood Tools - Spalted Maple Burl #3 - Work with Craig Jackson to round this maple blank
By: Christine Caliendo
February 14, 2010 · 7,442 views

Getting your wood blank round. Watch Craig as he continues to round out the maple spalted burl. See our website for more information on the tools used in this video www.easywoodtools.com or call 270-903-4270. Our tools are proudly made in the USA and our shop is located in Owensboro, Kentucky.

 

Easy Wood Tools - Spalted Maple Burl #2 - Getting your blank round with Craig Jackson
By: Christine Caliendo
February 14, 2010 · 9,197 views

Getting your wood blank round. Join Craig in this video while he gets the dry maple spalted burl round. See our website for more information on the tools used in this video www.easywoodtools.com or call 270-903-4270. Our tools are proudly made in the USA and our shop is located in Owensboro, Kentucky.

 

Easy Wood Tools - Spalted Maple Burl # 1- Roughing your square blank out to round with Craig Jackson
By: Christine Caliendo
February 14, 2010 · 13,965 views

Roughing out a Spalted Maple Burl with Craig Jackson of Easy Wood Tools. Let's get started with a square dry maple blank. See our website for more information on the tools used in this video www.easywoodtools.com or call 270-903-4270. Our tools are proudly made in the USA and our shop is located in Owensboro, Kentucky.

 

Easy Wood Tools FAQ: How do you cut, Left, Right and Plunge straight in on woodturning projects.
By: Christine Caliendo
February 14, 2010 · 5,952 views

Easy Wood Tools explains cutting Left, Right and Plunging straight in on your woodturning projects. See our website for more information on the tools used in this video www.easywoodtools.com or call 270-903-4270. Our tools are proudly made in the USA and our shop is located in Owensboro, Kentucky.

 

Easy Wood Tools FAQ 2: How to cut Left, Right and Plunge Straight with Easy Wood Tools
By: Christine Caliendo
February 14, 2010 · 7,435 views

Easy Wood Tools explains cutting Left, Right and Plunging Straight in to your woodturning project. Also explained is the Easy Grip Handle. See our website for more information on the tools used in this video www.easywoodtools.com or call 270-903-4270. Our tools are proudly made in the USA and our shop is located in Owensboro, Kentucky.

 

Easy Wood Tools FAQ: Which tool should I use to rough out my woodturning project?
By: Christine Caliendo
February 14, 2010 · 14,757 views

Which tool should I use to rough out my woodturning project? Compare the Ci1 Easy Rougher and the Ci0 Easy Finisher for your project See our website for more information on the tools used in this video www.easywoodtools.com or call 270-903-4270. Our tools are proudly made in the USA and our shop is located in Owensboro, Kentucky.

 

Easy Wood Tools FAQ: Which tool does a better finish quality cut, Easy Rougher and Easy Finisher?
By: Christine Caliendo
February 14, 2010 · 23,296 views

Quality Finish Cuts Comparison between the Ci0 Easy Finisher and the Ci1 Easy Rougher (R4 and R2 cutters) See our website for more information on the tools used in this video www.easywoodtools.com or call 270-903-4270. Our tools are proudly made in the USA and our shop is located in Owensboro, Kentucky.

 

Original S Series Carbide Woodturning Tools
By: woodturningtools
November 16, 2009 · 26,777 views

Watch our S17 and S10 make short work of some hard wood blanks. The turning times were 1/3 of the time it would take with a bowl gouge and note the tool is flat on the tool rest and very easy to learn how to use. http://www.carbidewoodturningtools.com http://www.woodturningblanks.com

 

Easy Wood Tools Woodturning Spindle 1 - Ci1 Easy Rougher
By: Christine Caliendo
March 16, 2008 · 28,632 views

See our website for more information on the tools used in this video www.easywoodtools.com or call 270-903-4270. Our tools are proudly made in the USA and our shop is located in Owensboro, Kentucky.

 

Easy Wood Tools Woodturning tool Ci1 Easy Rougher- Carbide Insert
By: Christine Caliendo
February 12, 2008 · 38,775 views

See our website for more information on the tools used in this video www.easywoodtools.com or call 270-903-4270. Our tools are proudly made in the USA and our shop is located in Owensboro, Kentucky. www.EasyWoodTools.com. 'The Next Step in Woodturning' Customer reviews---http://www.woodturnersresource.com/cgi-bin/yabb2/YaBB.pl?num 1204327388 This video is in REAL time, not fast motion. The Ci1 Easy Rougher is a carbide insert woodturning tool that addresses fatigue, safety, and efficiency like no other type of tool on the market. It is designed to safely and effortlessly re

 

Return to Turning Videos

Great Bargains
(ends April 25, 2019)


Square Mini Ergonomic Carbide Turning Tool

On Sale for only $49.99

Save $30.00

List price: $79.99

This Square Carbide Mini Turning Tool from Rockler features a replaceable and rotatable cutter that eliminates the hassle and downtime of sharpening. Simply rotate the carbide cutter for a fresh, sharp edge, and replace it once all available edges have grown dull. The solid carbide cutter also stays sharp for longer when compared with steel, giving you a much longer useful life. Shaft features a flattened back for stability when using the tool rest. The handles are made of solid ash encased with a thick, molded rubber end for an enhanced grip and reduced fatigue.

Click here for more information or to purchase

 


Starter Pen Turning Kit

On Sale for only $59.99

Save $10.00

List Price: $69.99

This kit contains all the essential tooling you need to start turning custom pens. It includes three pen blank species (bloodwood, bubinga and olivewood), three gold-plated Slimline Twist Pen Hardware Kits, a 7mm mandrel with knurled nut and #2 Morse Taper, 7mm bushings, a 7mm Brad Point Drill Bit, a 1 oz. bottle of CA Glue, a Pen Mill Kit for truing up all mating surfaces and a storage case with 28 adjustable compartments. The Pen Mill includes four pilot shaft sizes for a wide range of pen types.

Click here for more information or to purchase

 


Rockler Four-Piece Cheese Knife Turning Kit

7/8" On Sale for only $29.99

1 1/4" On Sale for only $39.99

Save $10.00

List Price: $39.99

The cheese cutters are made from food-grade 304 stainless steel and attached to the handles which you turn. The kit includes 1/4-20 threaded inserts. The cheese cutters themselves are dishwasher safe; the handles are easily removed for this purpose.

Click here for more information or to purchase


GVS Elipse P100 Half Mask Respirator with 2 Bonus Filters, Small/Medium

For only $25.99

Save $11.99

List Price: $37.98

These Elipse P100 Half-Mask Respirators from GVS are designed to protect against dust particles, metal fumes, mists, oil and water vapors, and even some micro-organisms. Each mask includes two low-profile filters, which permit a wide field of view, and won't interfere with safety glasses and sanding shields. The filters are easily interchangeable, and replacement filters are readily available.

Click here for more information or to purchase


Uvex Bionic Face Shield with Clear Polycarbonate Visor and Anti-Fog/Hard Coat

For only $32.74

Save $13.70

List Price: $46.44

Shell offers built-in chin protection and extended top-of-head coverage. Highly adjustable headgear tilts visor nearer or farther from face depending on preference and application. Comfortable cell foam on back of headgear. Breathable, removable, washable headband. Comfortably worn with most goggles and respirators.

Click here for more information or to purchase


4-Piece Safety Kit

For only $19.99

Save $15.00

List Price: $34.99

Push stick with ergonomic handle has embedded magnet for easy storage on your saw. Ideal for table saw and router table use. Angled push blocks feature ultra-grippy Bench Cookie pad material. They are great for jointer and router table applications. Table featherboard assists in holding stock against the fence while sawing or routing and helps to reduce kickback. It fits standard 3/4" x 3/8" miter slots found on table saws and router tables, and features expandable miter track bars for maximum holding power.

Click here for more information or to purchase


Powered by Google

Our Monthly Update

We update our home page about monthly to feature a new project, a new article, and a new and hot tool. Then we send an email to alert our subscribers.
We never let anyone use our list, and our subscribers have been wonderfully loyal as a result.

We hope you will try it out!

Sign Up For Our Newsletter

A Sampling of our Sponsors:
(Visit the Vendor's Corner above to see all our sponsors)

Robust Tools
Stainless Steel Bottle Stoppers
Rubber Chucky Products

(Click any Ad to go to our Sponsor's Website)