Woodturning Online Videos


Welcome to the Woodturning Online Videos page.

This video content was created by woodturner, Rick Morris. He has created a way to monitor all the videos in YouTube that are woodturning related.

Each month, Rick updates the video listings below. If you would like to learn about new videos, sign up for our free newsletter where we will list the top 20 videos each month.

Any categories in BOLD have sub-categories to help you narrow down your search.

Bandsaws Videos (105)

Sort by

Or click here to: Search All Videos


Woodturning - Cast Iron Bandsaw Table Clean Up
By: Mike Waldt
October 25, 2018 · 2,458 views

My method of cleaning heavy rust off my cast iron Bandsaw table

 

Band Saw Table Extensions for Slicing of Wide Boards with the Accu-Slice
By: SIS Woodworking
October 18, 2018 · 350 views

This video describes the production and application of table extensions to the front of the band saw table to enable the slicing of wide boards with the Accu-Slice band saw accessory. The extensions are made from 2' x 3' iron angles which are mounted to the font edge of the band saw table. Using these extensions it is now possible to slice bords up to 5' wide with the Accu-Slice System.

 

Accu Slice Installation
By: SIS Woodworking
August 03, 2018 · 296 views

This video describes the installation of the Accu-lice System.

 

Ordering the Accu Slice System
By: SIS Woodworking
August 03, 2018 · 477 views

This video describes the options available when ordering the Accu-Slice System to fit your band saw. There are three models of the Accu-Slice Index Table, five sizes of Accu-Slice Rails and two options for the Accu-Slice Carriage.

 

Accu-Slice Description
By: SIS Woodworking
August 03, 2018 · 452 views

The Accu-Slice is a band saw accessory to provide for the safer cutting of veneers and thin slices of wood on the band saw. With conventional resawing, the wood is both pushed against the fence and also at ninety degrees through the blade. Any change in hand pressure or hand repositioning results in saw marks on the cut piece of wood. This does not occur with the Accu-Slice. In addition the operation is much safer with the Accu-Slice since the operator's fingers are far removed from the band saw blade. The system operates much like a wood sawmill in which the wood or board to be cut is attached to a carriage which slides on a rail through the band saw blade. This provides for clean and smooth cuts and at the same time provides for greater safety for the operator.

 

Band Saw Circle Jig - Episode 138
By: Paul Lockwood
July 17, 2018 · 763 views

I finally decided to make a circle cutting jig for the Band Saw. In the past I've seen a few others had made and from memory decided to put my own take on it. Using only scraps of plywood I have laying about the whole thing was quickly made with a sliding guide in the centre so that almost any size of disc can be cut. I've drilled 3 holes to hold different sized pins, again for different types of work. Very cheap and quite quick to make, surely a must if you have a bandsaw. You can find me on the below Social Media Instagram: https://www.instagram.com/paul.a.lockwood/ @paul.a.lockwood Twitter: https://twitter.com/paullockwooduk @paullockwooduk Facebook: https://www.facebook.com/PaulLockwood.Woodworking/ Pinterest: https://www.pinterest.co.uk/lockwood3538/ Etsy: https://www.etsy.com/uk/shop/PaulLockwoodUK Please Subscribe http://www.youtube.com/channel/UCJmcpalJi_xzP_iV3uXJj2w?sub_confirmation 1

 

DIY Bandsaw Blade Sharpening With a Rotary Tool
By: Mike Peace Woodturning
July 06, 2018 · 2,183 views

I show you how I sharpen my bandsaw blades quickly using a rotary tool like a dremel. It is fast and saves you money! I upload new wood turning videos regularly so Ya’ll come back, hear? Want to support my channel? Check out my Amazon shop https://www.amazon.com/shop/mikepeacewoodturning Disclaimer: If you click on one of the product links, I’ll receive a small commission. This helps support my channel and allows me to continue to make videos like this. Thank you for the support! You can download demonstration handouts, downloadable copies of articles I have published, and other useful woodturning information available on my website http://mikepeacewoodturning.blogspot.com/p/woodturning-resources.html

 

Bandsaw Upgrade Pricing Info
By: Gord Rock
June 03, 2018 · 744 views

Information I forgot to provide on pricing of the Bandsaw Upgrade Kit I installed. Harold Bowern's Channel: https://www.youtube.com/channel/UCUjh0T6dqU4UQKeVlJGaR2A

 

Upgrading My Delta Bandsaw
By: Gord Rock
May 31, 2018 · 1,826 views

Upgrading my 14' Delta bandsaw with a kit from Carter Products. Made in the USA and very high quality kit!! I'm thrilled with how well my bandsaw works now!

 

Your Bandsaw and Green Wood
By: Mike Peace Woodturning
May 15, 2018 · 2,307 views

I share a tip on cleaning your bandsaw after cutting green wood, I upload new wood turning videos regularly so Ya’ll come back, hear? Want to support my channel? Check out my Amazon shop https://www.amazon.com/shop/mikepeacewoodturning Disclaimer: If you click on one of the product links, I’ll receive a small commission. This helps support my channel and allows me to continue to make videos like this. Thank you for the support! You can download demonstration handouts, downloadable copies of articles I have published, and other useful woodturning information available on my website http://mikepeacewoodturning.blogspot.com/p/woodturning-resources.html

 

Woodturning - Changing the Bandsaw Ratios
By: Blind Woodturner
April 27, 2018 · 222 views

I found out recently that the ratios on my bandsaw could be changed so I had a tinker and changed them! *** Proudly sponsored by Axminster Tools & Machinery. Axminster Tools & Machinery offer an extensive range of quality, value for money tools and machinery. https://www.axminster.co.uk/ *** Join me, Chris Fisher, the Blind Wood Turner, in my workshop. I started out in life as a regular guy, working in auto body repair at BMW, until one day, completely out of the blue, a rare virus (Toxoplasmosis) reared its ugly head and caused me to lose my sight in a matter of weeks. Despite the cha

 

How to Cut Olivewood on the Bandsaw
By: Le PicBois
April 01, 2018 · 3,535 views

This is the first time I work with a piece of olivewood from Jerusalem. The grain in there is so beautiful. Hope you'll like it too! I'd make a smoking pipe with it later on. Stay tuned! I put together a list of some of the tools I use in my shop in case you might be interested: https://www.amazon.com/shop/lepicbois Oh and yeah... Happy April Fools' Day! ;) _______________________________________ Support me on Patreon: https://www.patreon.com/lepicbois Website: http://lepicbois.net/ YouTube: https://www.youtube.com/lepicbois Facebook: https://www.facebook.com/AtelierLePicBois Instagram: h

 

Unboxing POV of bandsaw riser block and a quick look at install on Harbor Freight bandsaw
By: Boston Woodturning
February 24, 2018 · 326 views

Unboxing bandsaw riser block POV and a quick look at install modifications made on harbor freight 14” bandsaw. - Boston Woodturning

 

Alignment of the Band Saw to Assure Optimum Performance of the Accu-Slice System
By: SIS Woodworking
February 17, 2018 · 586 views

It is important that the band saw blade is parallel to the miter bar slot on the band saw table to assure the optimum performance of the Accu-Slice system and avoid band saw blade drift. This video describes two methods to verify the alignment of the bands saw blade to miter bar slot and make recommendations on how to resolve the problem.

 

A Study of the Parameters Affecting the Burr on Wedges using the Accu-Wedge
By: SIS Woodworking
February 15, 2018 · 481 views

This is a study of the various band saw and Accu-Wedge parameters that might have an effect on the size of the burr that occurs on segmented wedges when they are cut on the band saw. We studied the band saw blades, blade tension, band saw blade guides, various types of wood, the speed of cutting and the mounting of the Accu-Slice in an attempt to see if any of these parameters had an effect on the size of the burr. The study determined that all of these factors had little effect on the size of the burr. The only parameter that had a minor effect was the angle of the cut on the band saw.

 

Clamping Fence for the Accu-Slice Carriage using an Offset Cam Clamp
By: SIS Woodworking
February 03, 2018 · 873 views

This video describes the design and fabrication of a clamping fence for the Accu-Slice band saw carriage that uses an offset cam clamp to attach segmented rings to the Accu-Slice carriage fence. This system is useful when one needs to attach segmented rings to the carriage without using double sided tape of glue to attach the segmented rings to the carriage.

 

Accu-Slice Tip - Quick Change Sacrificial Fence for the Accu-Slice Carriage
By: SIS Woodworking
January 20, 2018 · 687 views

A quick change sacrificial fence for the Accu-Slice System is described. This tip was inspired by Terry Tjaden. The sacrificial fence is fitted with screw inserts which permits the quick change of the sacrificial fence. The sacrificial fences are then attached to the carriage with thumb screws. By enabling the quick change of sacrificial fences with the boards to be sliced attached, a much more efficient use of segmented rings and wood can be achieved.

 

Installing A Carbide Laguna Tools Band Saw Blade
By: Gabe Castro
December 15, 2017 · 161 views

How to instill a new Carbide Resaw King Band Saw Blade on Grizzly 17 Band Saw.

 

Grizzly G0555P 14' Bandsaw Full Review
By: Casey Martin
December 01, 2017 · 2,292 views

Hey guys, please comment down below with any questions that I might have missed covering. Here is a link to the exact bandsaw: http://www.grizzly.com/products/The-Ultimate-14-Bandsaw/G0555

 

Rikon Band saw Resawing 16' Log
By: George Fotinakes
October 13, 2017 · 2,127 views

This video shows the ease of resawing green olive wood logs with the Rikon 14' band saw.

 

Bandsaw Cross Cut Jig
By: George Fotinakes
October 08, 2017 · 635 views

Step by step instructions for making a very functional cross cut jig for a band saw.

 

Bandsaw Circle Cutting Jig
By: John Clothier
September 17, 2017 · 882 views

In this video I show you how I created a jig for my bandsaw to allow me to cut circle blanks

 

Band Saw Laser Beam for Projecting the Band saw Blade Path
By: SIS Woodworking
August 01, 2017 · 2,222 views

The Band Saw Laser Beam is an attachment for the band saw to project a red laser line onto the board that is being cut. The Band Saw Laser system mounts to the top wheel housing of the band saw with magnets. After alignment, a laser beam line is projected onto the band saw blade teeth and then projected onto the exact path of the band saw blade cut. By projecting the laser onto the exact path of the band saw blade you can accurately cut your boards to the required dimensions. This is particularly helpful when using the Accu-Wedge segmenting system and the Accu-Slot Celtic Ring System. The Band Saw Laser is an additional safety feature for the band saw because it enables the operator to know exactly where the band saw blade will cut, and he can take additional precautions to keep the hands and fingers far removed for the band saw blade path.

 

Laguna Resaw King Test Cut - First Use
By: UBWoodman
July 12, 2017 · 1,341 views

First use of my Laguna 14/BX Resaw King blade to slice a board of Flame Box Elder Hot Swing by Kevin MacLeod is licensed under a Creative Commons Attribution license (https://creativecommons.org/licenses/by/4.0/) Source: http://incompetech.com/music/royalty-free/index.html?isrc USUAN1100202 Artist: http://incompetech.com

 

Introducing the Accu-Slot Celtic Ring Jig
By: SIS Woodworking
May 29, 2017 · 1,533 views

Introducing the new commercial version of the Celtic Ring Jig for the production of Celtic ring and knot patterns on the bandsaw for wood turning projects. This jig will be called the Accu-Slot and the prototype version will be demonstrated at the AAW meeting in Kansas City on June 23-25, 2017. The Accu-Slot is constructed from a 10' x 15' aluminum plate that has 4 roller bearing on its base that rides on the rail on the Accu-Slice system. The unit also incorporated a 2.5' high extruded aluminum fence with channel slots for the attachment of a wide variety of clamping systems. Finally the fence is adjustable from 30 degrees up to 90 degrees with 1 degree accuracy. The system is scheduled for delivery in the fall of 2017. See our web site for additional details: www.sisweb.com/wood

 

Bandsaw Jig for Ripping Small Stock and Splines
By: Dave's Woodshop
May 24, 2017 · 1,396 views

This video shows how there is a need to be able to cut small stock on a bandsaw safely while keeping the guides an optimal distance from the stock. There is then a step by step demonstration how to make a jig to facilitate this. There is then further demonstration of the finished jig in use.

 

RECORD POWER BS400 BAND SAW BLADE SETUP/CHANGE!
By: Nick Zammeti
May 18, 2017 · 8,906 views

This is a Craig from Record Power showing me how to change a blade on my Record Power BS400 Band Saw. Record Power Band Saw Range http://www.recordpower-thetoolshop.com/acatalog/Bandsaw_Machines.html?gclid CjwKEAjwxurIBRDnt7P7rODiq0USJADwjt5DcU6GpR3_PCPJIRkKmoF_w4_HQ7ig-QctsY7TwNRtSBoCJA7w_wcB MOST ITEMS I MAKE ARE ON MY WEBSITE http://www.nzwoodturning.co.uk/ CHARLIE THE MAKER (My little boys channel) https://www.youtube.com/channel/UClU3oIHFJwi4_UF-l_Lc7cw MY NZ WOODTURNING EMBLEMS (round brass logo makers mark) http://www.williams-eng.co.uk/ THE RESIN I USE IS FROM HERE http://www.e

 

Turning With A Chainsaw??!!!
By: RickTurns
May 10, 2017 · 2,417 views

I recently purchased a new electric chain saw, and in this video, I demonstrate it, review it, and replace the chain because I hit a chunk of metal embedded in a log.

 

Rikon BandSaw Belt Replacement
By: Turning Round
May 09, 2017 · 4,481 views

In this video I replace the belt on my Rikon 10-325 Band Saw. The belt came off the pulley and got shredded. It is a pretty simple repair. You take the Bandsaw wheel off, clean it up and replace with a newer belt and then re tension. Here is a link to the newer version of this bandsaw. RIKON Power Tools 10-326 14 Deluxe Bandsaw href 'https://www.amazon.com/gp/product/B01D35Z3PU/ref as_li_tl?ie UTF8&camp 1789&creative 9325&creativeASIN B01D35Z3PU&linkCode as2&tag turninground-20&linkId a63a93a08e30972a0c9470724f3fba24' Add to the Bottom of each video. Check out my Etsy Store: https://www.etsy.com/shop/TurningRound Check out my Website: http://turninground.biz/ Or support me on Patreon: https://www.patreon.com/TurningRound Or Find me in Instagram as: TurningRound https://www.instagram.com/turninground/ Thanks for watching.

 

Design and Production of a Bandsaw Jig for Making Celtic Rings and Celtic Knots
By: SIS Woodworking
April 22, 2017 · 9,505 views

The design and production of a bandsaw jig for making Celtic Rings and Celtic Knots. Two versions of the jig are described - one unit uses the miter bar slot on the band saw and the second version uses the Accu-Slice system. Complete details and a video description of the making of the jig and its operation. The jig incorporates a variable angle fence, adjustable board cutting position and a stop to prevent cutting the whole way through the board. Utilizing this jig one can make complex multi circle Celtic patterns for lathe turning.

 

Slicing Long Boards on the Accu-Slice Band Saw Accessory
By: SIS Woodworking
April 08, 2017 · 1,574 views

Slicing or resawing of long boards 48' to 54' long using the Accu-Sllice band saw accessory. The Accu-Slice is equipped with an 8 ft long rail and a 54' long L Bracket carriage to permit the cutting of long boards.

 

New band saw!!!!!
By: The AZ Viking
March 27, 2017 · 8 views

 

Slicing Plastics and Polymers with the Accu-Slice Band Saw Accessory
By: SIS Woodworking
March 23, 2017 · 956 views

Cutting and slicing various plastics and plastic polymers with the Accu-Slice Band saw accessory to evaluate the finished cuts on the band saw. Slicing, acrylic, polypropylene, nylon, PVC, UHMW, Delrin, and Polycarbonate. All of the plastics produced boards that were flat and perfectly parallel on all sides. Some of the plastics cut better than others. Acrylic plastics were able to be cut for use in woodworking applications such as fillers. Various band saw blades were evaluated to determine what would work best in cutting plastics on a band saw without any lubricant.

 

How much runout can you live with Bandsaw
By: Rich McNatt
March 11, 2017 · 531 views

 

Band Saw Blade Drift Using the Accu-Slice
By: SIS Woodworking
February 27, 2017 · 2,948 views

Elimination of Band Saw Blade Drift using the Accu-Slice Band Saw resawing accessory. Review of the causes of band saw blade drift in conventional resawing and how it is eliminated with the Accu-Slice.

 

DIY Bandsaw Sled
By: dashrocket
February 05, 2017 · 213 views

 

Accu Slice - Resawing and Cutting Wide Boards
By: SIS Woodworking
January 15, 2017 · 6,807 views

Resawing and slicing thin sections of wood boards up to 12' wide utilizing the Accu-Slice band saw accessory. Slices as thin as 0.010' thick can be sliced from 12' wide boards with an accuracy of 0.002' in thickness on all the edges of the sliced board. The sliced pboards are straight and all edges and surfaces are parallel. In addition the sliced board surface is much smoother than conventional wood resawing on the band saw requiring no plaining and minimal sanding of the board surfaces. In addition blade drift is eliminated since the wood being sliced is mounted to the Accu-Slice fence. This technique is used in producing thin veneers, matched book panels and other thin slices of wood. Also a comparison of different band saw blades to compare the finished resulting from these various band saw blades.

 

Accu Slice - Cutting Thin Slices from a Large Segmented Wood Disc
By: SIS Woodworking
January 15, 2017 · 3,550 views

Cutting and Slicing thin rings from a large segmented wood discs utilizing the Accu-Slice band saw accessory. Slices as thin as 0.010 inch thick can be sliced from segmented wood rings as large as 12 inches in diameter with an accuracy of 0.002' around the entire circumference of the segmented ring slice. Also resawing boards up to 12 inches wide to produce thin veneers, matched book panels and thin wood boards as thin as 0.010' with an accuracy of 0.002'

 

Introducing the Accu-Slice
By: SIS Woodworking
December 28, 2016 · 13,399 views

The Accu-Slice System was developed to permit the safer resawing and slicing of wood on a band saw. The hands and fingers are far removed from the band saw blade. The sliced boards have smoother surface cuts with straight & parallel sides that do not require planing and minimal sanding. This video describes the unique features of the Accu-Slice and demonstrates its capabilities.

 

Accu-Slice Installation
By: SIS Woodworking
December 21, 2016 · 21,002 views

The installation of the Accu-Slice on a band saw to achieve the optimum smooth cut surfaces on the band saw.

 

Folding a bandsaw blade
By: Andrew Whale
December 19, 2016 · 186 views

Hi A very short video on the best way I have found to fold a bandsaw blade. I hope you find it useful. Cheers! Andrew Disclamer: I do not recommend any of the methods/techniques I use as these could be unsafe. Woodturning is a potentially hazerdous activity and it is your responsibility to use proper methods/techniques and follow appropriate health and safety practices.

 

Accu-Slice - Segmented End Plate
By: SIS Woodworking
December 08, 2016 · 18,082 views

The production of the top or bottom segmented discs for bowls, eggs and the bell of a previous video. This video is a supplement to another video demonstrating the production of segmented wood bells, in which these segmented discs were used to the top of the bells.

 

Awful noise on the bandsaw
By: R4X Woodturning
December 03, 2016 · 410 views

I tuned up my bandsaw and had an awful noise when I started it for the first time afterwards. I used this video to help me trace the source of the noise and eliminate it. Imgur album of the whole process: http://imgur.com/gallery/eyv8z Instagram: https://www.instagram.com/r4x_woodturning/?hl en

 

Tuning the bandsaw.
By: R4X Woodturning
December 03, 2016 · 67 views

In this video, I am adjusting the tension of the bandsaw blade for optimal cutting. Imgur album of the whole process: http://imgur.com/gallery/eyv8z Instagram: https://www.instagram.com/r4x_woodturning/?hl en

 

Accu-Slice - Cut Thin Wood Slices with Bandsaw
By: SIS Woodworking
November 24, 2016 · 14,364 views

The Accu-Slice band saw jig permits the safe and accurate cutting of thin sections of wood (resawing) and can also slice thin sections of wood, such as segmented disc rings, and other small pieces of wood. http://www.sisweb.com/wood

 

Accu-Slice - Wood Turner Meeting
By: SIS Woodworking
November 24, 2016 · 1,111 views

October 2016 meeting of the Bucks Woodturner's where the Accu-Slice system was first introduced and described. The Accu-Slice band saw jig is used to safely and accurately cut thin slices of wood and can also cut small and irregular pieces of wood. http://www.sisweb.com/wood

 

SAFELY Slice A Disc On A Bandsaw.
By: Gord Rock
November 17, 2016 · 2,916 views

How to slice a round disc simply & SAFELY on the bandsaw.

 

Axminster HBS250N Bandsaw Unboxing
By: John Clothier
November 15, 2016 · 7,685 views

I purchased a basic bandsaw from Axminster for the shed. Here I unbox it and put it all together before testing it out. This is not a review as I have nothing to compare it to but I do give my opinions along the way.

 

How to ' fold' a Bandsaw blade
By: Rich McNatt
August 24, 2016 · 394 views

Some times it is a pain to fold a bandsaw blade, This is how easy it is.

 

Does sharpening a Bandsaw blade really work?
By: Steve Krumanaker
July 05, 2016 · 4,844 views

Short video of using a dremel with a chainsaw stone to sharpen a band saw blade.

 

Bandsaw Circle Cutting Jig
By: Peter Matthew
June 10, 2016 · 3,360 views

Watch and see how I made this circle cutting jig for my bandsaw! Darbin Orvar Circle Cutting Jig: http://www.darbinorvar.com/blog/2015/7/22/how-to-make-a-circle-cutting-jig-for-a-bandsaw www.peterturnswood.com ----------------------------------------­­­­---------- To see my vlog and follow-up channel, go to my main channel by clicking 'Peter Matthew' up above. On my main channel, look to the right side of the screen where it says 'Featured Channels'. Under 'Featured Channels' is 'Peter Matthew 2'. Click that and subscribe to that channel :) ----------------------------------------­­­­­­­­­­­

 

Band Saw Drift/Urn Follow-up
By: The Woodshop
May 02, 2016 · 3,509 views

Setting up a fence to compensate for band saw drift. RZ Mask Website www.rzmask.com/pages/woodworking Caleb Weller https://www.youtube.com/channel/UCVi2jn1Oj9w_qLuSvu2zt3Q/featured Mike Fulton https://www.youtube.com/user/mfwoodshop Segment Calculator https://play.google.com/store/apps/details?id com.byroid.segmentcalculator1 I upload a new project video every Friday. Thank you for supporting free woodworking My Etsy shop https://www.etsy.com/shop/Thewoodshoptv Patreon https://www.patreon.com/CarlJacobson Schedule demos, and one-on-one online classes jacobson

 

Bandsaw Tire Installation & Blade Set Up
By: Braxton Wirthlin
April 22, 2016 · 4,477 views

Here's a quick and easy way to use a heat gun to install urethane tires on your bandsaw. Urethane tires can be very hard to stretch on, but with a little heat from a heat gun they'll go on easy. I also show you how to set up your blade for nice straight cuts with very minimal drift. Be sure to check out Patrick from Patrick's Workshop's video on how he installs his tires. Thanks for watching! Patrick's bandsaw video -https://youtu.be/8LlqUqrwDF8 Patrick's channel - https://www.youtube.com/user/Patricksworkshop braxton@timbermfg.com Instagram - https://instagram.com/bwirthlin Facebook - https://www.facebook.com/timbermanufacturing twitter - https://twitter.com/braxtonwirthlin Timber Manufacturing http://www.timbermfg.com Instagram - https://instagram.com/timbermfg twitter - https://twitter.com/timbermfg - - - - - - Please watch: 'Olive Branch Bowl' https://www.youtube.com/watch?v iIp6QYBSU0c - - - - - -

 

No Bandsaw? No Problem!
By: Brian Havens
March 13, 2016 · 85,296 views

Most woodturners will cut half-logs into rounds on the bandsaw before mounting it onto the lathe, and for production turners the time saved in doing so is a must—and the money saved would even pay for bandsaw. But for the hobbyists who cannot afford the space or budget for a bandsaw, that should not keep you from taking advantage of all the free wood from local trees that are cut down. See how a special roughing cut (that I call a 'pivoting cut') can make quick work of rounding out half logs directly on the lathe.

 

Making a Bowl Cutting Jig For The Bandsaw Quick and Easy
By: The Russian Woodworker
February 14, 2016 · 1,594 views

In this video I make a jig to help cutout perfect bowl blanks that I can use on my bandsaw.

 

#56 Shop Tour and Bandsaw Mod
By: DIY with Uncle Cy
January 24, 2016 · 508 views

So here is my first video of the year. I am showing the modifications to the shop and modifying my 9 inch band saw to cut larger projects (kinda). I was feeling kinda goofy while making this so prepare for a lot of not so funny jokes at my own expense.

 

Laguna 1412 Bandsaw Review
By: Dave's Woodshop
January 12, 2016 · 26,151 views

A review and demonstration of the Laguna 1412 Bandsaw. The 1412 is Laguna's first 110v bandsaw.

 

Video #5 Segmenting Sled For The Bandsaw
By: AnkleBiter Woodworks
November 27, 2015 · 4,544 views

Building of a segmenting sled for my 17' band saw. Fairly simple construction with positive stops at the angles for typical numbers of segments. As always: comments and suggestions are welcome! Don't forget to subscribe! Like us on Facebook: https://www.facebook.com/anklebiterwoodworks Visit our website: https://www.anklebiterwoodworks.com

 

Woodturning Bandsaw Jig Keeps Fingers For Another Day
By: As Wood Turns
September 24, 2015 · 6,925 views

http://www.AsWoodTurns.com In last week's video, I showed a bandsaw jig that I used to safely saw a vase. At first, I thought that it was too simple to do a video on but then I reconsidered due to how dangerous a bandsaw can be. So for a bit of bandsaw safety, here it is. BTW, if you need a 1.25' x 8 tpi bolt and nut, search for A193B7. Mine came from FMW Fasteners. Good turning. Enter your email at http://www.AsWoodTurns.com & I'll let you know when the next easy woodturning project video is ready. Blog: http://www.AsWoodTurns.com FB: http://www.Facebook.com/AsWoodTurns

 

Circle Jig for the bandsaw
By: Jürgen Glaser
September 16, 2015 · 1,879 views

If you want to cut absolutely round pieces on your bandsaw you need a circle jig. See also the plan on http://www.juergens-holzweg/plans.php

 

Circle Cutting Jig For the Band Saw
By: Jerry Brown
August 25, 2015 · 1,157 views

Today I made a jig for cutting a circle on the Band Saw and went over some of what has been going on with the projects.... or lack there of... :)

 

Grizzly G0513ANV Bandsaw Review
By: Peter Matthew
August 09, 2015 · 11,405 views

Grizzly Industrial: http://grizzly.com G0513ANV Bandsaw: http://grizzly.com/products/17-2-HP-Bandsaw-Anniversary-Edition/G0513ANV ---------------------------------------------------------------------------------------------------------------- Let me know if you enjoyed the video and hopefully this review was helpful to some of you guys considering buying a new bandsaw! Please like, comment, and share! ---------------------------------------------------------------------------------------------------------------- Contact me: peterturnswood@gmail.com My eBay store: http://www.ebay.com/usr/dste6080

 

Bandsaw crosscut Sled and Milling Jig, Rikon 14 inch deluxe Bandsaw
By: Chad Schimmel
August 07, 2015 · 18,422 views

This video shows my new bandsaw and also the sled I made for crosscuts and long cuts. IF you like the video give it a thumbs up and don't forget to subscribe to the channel. Here are the tools and equipment I use, I have included these amazon links because I get a commission if these items are purchased. I only ask if you are going to buy them anyway please use these links and that will help the show and the shop. Thank you Jet 1221 lathe, http://amzn.to/2sUR5mF Jet 1015 lathe, a little cheaper price, http://amzn.to/2ue7Ld1 Metal Lathe, http://amzn.to/2eMuBSH Drill Press, http://amzn.

 

BandSaw Sled
By: Dave's Woodshop
August 01, 2015 · 4,529 views

A demonstration of my band saw sled. A brief discussion on band saw setup and eliminating drift. Sled construction and use explained.

 

#85 Increasing Capacity and Tuning a 14 inch Bandsaw
By: Stephen Ogle
July 26, 2015 · 14,027 views

After watching Al Furtado cutting blanks with his bandsaw with a riser block I decided to install the one I had for mine and never got around to installing. This video shows the procedures for installing a six inch riser to increase your 14 inch bandsaw capacity from six to twelve inches and also the tuning procedures I use to ensure smooth operation of my bandsaw. Hope you enjoy watching. I can be contacted through Facebook, or Google from the banner on my youtube homescreen. My email address is: stvnogl@gmail.com

 

Getting the best from my Bandsaw
By: Jake Webb
July 09, 2015 · 422 views

A personal journey about me, a cheap bandsaw and how I finally got it to do what I want. Turning a zero tolerance insert for this Bandsaw: https://youtu.be/OvJq_aE7JEw Music: http://www.purple-planet.com

 

Bandsaw Zero Tolerance Insert
By: Jake Webb
May 07, 2015 · 2,910 views

Turning a zero tolerance insert plate for my bandsaw, in an attempt to improve its cut. I will do a more in depth video on the bandsaw and its issues at a later date. I forgot to film the final fit but its nicely flush but could have been a bit snugger on its fit. It can jam when finer shavings get into it. It has made a minor improvement to the cleanest of the cut and i'm sure acts as another barring surface to help keep the blade from wandering. Follow up video of my journey to a good cut on this bandsaw is here https://youtu.be/bSyWqJ5_U8Y Music: http://www.purple-planet.com

 

Make Your Own Bandsaw Insert
By: Gord Rock
April 19, 2015 · 14,374 views

How to make your own insert to replace the chipped and worn one on your bandsaw.

 

WoodshopTour 01 Makita Bandsaw Review & Tuning (in Slovak language)
By: Dipa Das
April 13, 2015 · 115,586 views

This is first video from set 'Woodshop Tour' where i would like to show some tools & tips & tricks from my woodshop.. This is about Bandsaw Makita LB1200F and how to make two supporting tables.. Prvé video zo série 'Woodshop Tour', kde bych vám rád postupne ukázal nástroje s ktorými pracujem, tipy, triky, vychytávky a vylepšenia.. Toto video je o Pásovej píle Makita a ako si vyrobiť dva podporné stolčeky.

 

Milling Small Logs on the Bandsaw
By: Peter Matthew
March 27, 2015 · 3,030 views

Check out my ebay: http://www.ebay.com/usr/dste6080 Thanks for watching! Subscribe!

 

Band Saw Cool Blocks
By: Cip's Wood Chips
March 10, 2015 · 4,131 views

I have not been doing any woodturning because of the weather but I been doing some maintenance on my band saw. I install Olson Cool Block on the blade guide and learned to better tension the blade

 

Rikon 14 inch Bandsaw follup, tip and tricks.
By: Turning Round
March 07, 2015 · 13,526 views

In this video I start using my new Rikon 14 inch band saw. I have learned a few trick and tips about the saw. The saw works well and cuts nice clean pen blanks. Here is a link ott he newer version of this bandsaw. RIKON Power Tools 10-326 14 Deluxe Bandsaw href 'https://www.amazon.com/gp/product/B01D35Z3PU/ref as_li_tl?ie UTF8&camp 1789&creative 9325&creativeASIN B01D35Z3PU&linkCode as2&tag turninground-20&linkId a63a93a08e30972a0c9470724f3fba24'

 

Bandsaw Use for Wood Turning Part 1 of 2
By: Mike Peace Woodturning
March 04, 2015 · 3,882 views

Mike explains and demonstrates useful information for woodturners using a bandsaw for cutting woodturning blanks. This is part 1 of 2. Part 2 is available at: https://www.youtube.com/watch?v KKlDLVknu_E More resources on my blog at http://mikepeacewoodturning.blogspot....

 

Band Saw Use for Wood Turning part 2 of 2
By: Mike Peace Woodturning
March 04, 2015 · 2,523 views

Mike explains and demonstrates useful information for woodturners using a bandsaw for cutting woodturning blanks. This is part 2 of 2. Part 1 is available here: https://www.youtube.com/watch?v SxYW5JH8mp0 More resources on my blog at http://mikepeacewoodturning.blogspot....

 

First cuts on my Rikon Deluxe 14' 10 325 bandsaw!
By: Ethan Cook
March 03, 2015 · 656 views

Cutting 6 inch tall box elder into slabs to then cut into pen blanks / turning blanks. I had just finished setting up this saw in my shop and it is such an improvement over my last bandsaw!

 

Make a band saw fence Wood turning by Al Furtado
By: Rebel Turner
March 01, 2015 · 3,536 views

How to make a band saw fence that will perform like a champ. I made this fence and rail system for my band saw after buying it and realizing it lacked a fence or rails. if you are tired of having to use clamps to hold down a fence on your saw this might help.

 

The bandsaw wants to eat my fingers. Cutting Blanks.
By: Adze Woodturning
February 13, 2015 · 851 views

An easy method of cutting stock from green logs prepped with a chain-saw. I've cut all sides on the video but you really only need to cut two sides (one for the bed and one for the guide). I slipped when I was cutting but I was using push sticks...I still have all my fingers.

 

Rikon 14 inch 10-325 Band Saw, Installation and Setup
By: Turning Round
February 09, 2015 · 14,791 views

In this video I get my Rikon 14 inch band saw out of the box and show all the steps of putting it together and setting it up for the first cuts. The instruction are pretty hard to follow so this video really helps with the process Follow this link to find this saw and read more review. Here is a link to the the newer version of this Bandsaw. RIKON Power Tools 10-326 14 Deluxe Bandsaw href 'https://www.amazon.com/gp/product/B01D35Z3PU/ref as_li_tl?ie UTF8&camp 1789&creative 9325&creativeASIN B01D35Z3PU&linkCode as2&tag turninground-20&linkId a63a93a08e30972a0c9470724f3fba24'

 

Proxxon MICRO-Bandsaw MBS/E
By: mhcrafters
February 09, 2015 · 451 views

Available at http://mhcrafters.com

 

Bowl Blank on Bandsaw
By: John Bare
February 06, 2015 · 148 views

Making a bbows blank more or less round.

 

SJWoodShorts - Bandsaw followup, and Help Me!
By: SJWoodworks
October 23, 2014 · 3,167 views

I had some questions about the bandsaw and the setup, so I answer them here, and show some of the features of the new bandsaw. Then, I'm asking for help here. What do I need to complete the bandsaw package? Fences, other guides, whatever? I describe in the video what I'm going to be doing with the bandsaw, so take a look, then tell me what accessories I need to get! Carter Bandsaw Clinic: https://www.youtube.com/watch?v wGbZqWac0jU

 

Craftsman 12 Inch Band Saw Update and Repair
By: Turning Round
October 15, 2014 · 66,213 views

In this video I talk about my Craftsman Band saw and how I fixed it to perform better for the type of projects I am doing. I replace the blade and repair the pulleys on my saw and bring it back to life.

 

BANDSAWS & BOWL BLANK PREP by Reed Gray aka RoboHippy
By: robohippy
October 14, 2014 · 24,807 views

More in depth discussion by RoboHippy of Bandsaws and Bowl Blank Prep.

 

Bandsaw Log Cutting Jig Part 2
By: Gord Rock
September 16, 2014 · 18,141 views

Part 2 of the Bandsaw Log Cutting Jig. I forgot to mention how to cut slabs with the jig. Although many woodworkers will know how it works there may be some people new to the hobby who just wouldn't think of this.

 

Bandsaw Log Cutting Jig
By: Gord Rock
September 12, 2014 · 66,551 views

A jig to allow cutting of logs on a bandsaw. Cutting can be done either the length of the log or crosscut.

 

Jet Band Saw Riser Block Installation #9
By: I Turn Two
August 17, 2014 · 8,607 views

Step by step procedures for installing a riser block for a Jet 14' Band Saw increasing the resaw capability to 12'.

 

Band Saw Circle Cutting Jig
By: RJBWoodTurner
April 27, 2014 · 7,372 views

I have an idea for a game I want to build and the game requires 10 circles of different sizes. I needed a jig to cut 10 perfect circles so I built this simple tool to assist in that process. Game video coming soon.

 

#93 Como doblar la sierra de cinta - How to fold band saw blade
By: Miguel Sanchez
April 21, 2014 · 11,829 views

Ayuda al canal: www.patreon.com/miguelsanchez Help the channel: www.patreon.com/miguelsanchez Otro pequeño truco para aprender a doblar facilmente la sierra de cinta, sobre todo para los que empiezan. Another small trick for those who start. http://www.facebook.com/profile.php?id 1181903663 http://www.tornoartesano.es miguel@tornoartesano.es

 

#90 como medir la sierra de cinta - Band saw blade measurament
By: Miguel Sanchez
April 16, 2014 · 8,877 views

Ayuda al canal: www.patreon.com/miguelsanchez Help the channel: www.patreon.com/miguelsanchez Otro pequeño truco para los que empiezan. Another small trick for beginers. http://www.facebook.com/profile.php?id 1181903663 http://www.tornoartesano.es miguel@tornoartesano.es

 

Band Saw Drift
By: Ron Calverley
January 06, 2014 · 479 views

How I set up for 'Band Saw Drift'

 

#42 Configurando la sierra de cinta (resubido)
By: Miguel Sanchez
October 23, 2013 · 155,812 views

Ayuda al canal: www.patreon.com/miguelsanchez Help the channel: www.patreon.com/miguelsanchez Vamos a un breve repaso a la configuracion optima de nuestra sierra para que nos de los mejores resultados con el minimo esfuerzo. http://www.facebook.com/profile.php?id 1181903663 http://www.tornoartesano.es miguel@tornoartesano.es

 

Band-sawing a Bowl Blank: Woodturning
By: WYOMINGWOODTURNER
October 10, 2013 · 5,125 views

Sam demonstrates how to cut a circle with a simple jig. He then cuts an ash bowl blank free hand on the bandsaw.

 

Band Saw Basics
By: Mike Waldt
July 07, 2013 · 13,682 views

An introduction to the basics of The Band Saw

 

BAND SAW Blade DRIFT
By: WYOMINGWOODTURNER
June 25, 2013 · 56,482 views

Sam explains band saw blade drift and how to deal with it when making a straight cut on your saw.

 

Bandsaw Table Upgrade for milling Pen Blanks
By: WYOMINGWOODTURNER
June 25, 2013 · 8,001 views

Sam shows a band saw table with an improvement. Set in the table is a slot for a crosscut guide which provides for safe milling of pen blanks and other small pieces of wood.

 

#35 Cortando circulos perfectos
By: Miguel Sanchez
June 05, 2013 · 488,587 views

Ayuda al canal: www.patreon.com/miguelsanchez Help the channel: www.patreon.com/miguelsanchez Un soporte sencillo para ayudarnos a preparar la madera antes de mandarla al torno, espero que os sea de utilidad.

 

46 - Bandsaw Demo - Dave Powles - 2 Oct 2012
By: Waxhaw Woodturners
January 21, 2013 · 2,119 views

Waxhaw Woodturners http://www.waxhawwoodturners.com Come join us! Waxhaw Woodturners http://www.waxhawoodturners.com Video by Daniel Brinneman http://www.lionsdendesigns.com Video by Daniel Brinneman. https://danielbrinneman.com

 

sled for cutting segments on bandsaw
By: Segmentedturning
December 17, 2012 · 7,829 views

Hello again, In this video I just go through how I make my sleds for cutting the segments on my bandsaw. The process is pretty simple and the finished article does a good job over and over. I hope I dont confuse you to much. www.segmentedturning.co.uk

 

Replace 14 inch Woodworking Bandsaw Tires with Urethane
By: Mark Hammond
October 06, 2012 · 25,241 views

Replacing broken and worn out bandsaw tires on a 14 inch woodworking band saw. These were replaced on a Porter Cable saw but the process should be about the same on a Jet, Delta, Powermatic, Grizzly or any other 14' band saw. One old tire broke and the other was just worn. The replacements tires are .125 urethane. The kit I ordered came with a band-aid which i thought was funny when I opened the package. They knew something I didn't. :)

 

Stradatura o allicciatura
By: Livio Maritati
October 05, 2012 · 18,841 views

Come mantenere efficiente la lama della sega a nastro con un jig autocostruito per la corretta stradatura

 

Affilare le lame della nastro
By: Livio Maritati
September 12, 2012 · 34,167 views

A volte si presenta la necessità di ritoccare il filo della lama della sega a nastro: ecco come farlo in pochi minuti

 

Jet JWBS 16Q Bandsaw Video
By: ian metheringham
July 16, 2012 · 791 views

he Jet JWBS-16 MK2 is intended for heavy work and has cast iron blade wheels, a super cast iron table which can tilt from -10 to 45 , a locking rip fence which is supported at the front and rear of the table and extends slightly beyond the cast iron table to give an excellent capacity on both sides of the blade. On the face of the rip fence is a point cutting attachment which is ideal for re-sawing. The mitre fence is 'T' slotted into the table for accuracy, safety and extended capacity. buy online at http://www.turnerscabin.co.uk/index.php?main_page product_info&cPath 3_109_146&products_id 449

 

woodturning bandsaw box
By: bradturbo44
April 17, 2012 · 1,337 views

woodturning bandsaw box

 

Band saw box on the lathe
By: Carl Jacobson
March 30, 2011 · 111,786 views

I've seen a lot of bandsaw boxes, but never a turned one. You can find plans, and ideas for bandsaw boxes all over YouTube. I think it turned out ok, but it was fun to try something new. If you make one of these I'd really like to see it, you can always share your project on my website. Here's a link to some of the tools I used in this video, http://astore.amazon.com/thewood0c-20 I upload a new project video every Friday. Thank you for supporting free woodworking My Etsy shop https://www.etsy.com/shop/Thewoodshoptv Patreon, I really appreciate your support. https

 

band saw tips.avi
By: Cap'n Eddie Castelin
February 24, 2010 · 46,285 views

How to tune up your saw with a few quick steps

 

Return to Turning Videos

Powered by Google

Great Bargains


Bowl Turner's Tool Rest

On Sale for only $39.99

Save $10.00

List price: $49.99

Click here for more information or to purchase


Pneumatic Swiveling Shop Stool

On Sale for only $35.99

Save $24.00

List Price: $59.99

Click here for more information or to purchase

 


Dust Bee Gone Mask

For only $39.99

Seen elsewhere for $43.99-$49.99

Available in medium, large and x-large)

Click here for more information or to purchase


Pen Press/Drilling Jig

On Sale for only $89.99

Save $10.00

List Price: $99.99

Click here for more information or to purchase

 


Trend® Air Circulating Airshield Pro

On Sale for only $349.99

Save $40.00

List Price: $389.99

Click here for more information or to purchase

 


Powered by Google

Our Newsletter

We update our home page about monthly to feature a new project, a new article, and a new and hot tool. Then we create a newsletter to alert our subscribers.
We never let anyone use our list, and our subscribers have been wonderfully loyal as a result.

We hope you will try it out!

Sign Up For Our Newsletter

A Sampling of our Sponsors:
(Visit the Vendor's Corner above to see all our sponsors)

Hunter Woodturning Tools
From Walnut to Antlers
Woodturning Online

(Click any Ad to go to our Sponsor's Website)