Woodturning Online Videos


Welcome to the Woodturning Online Videos page.

This video content was created by woodturner, Rick Morris. He has created a way to monitor all the videos in YouTube that are woodturning related.

Each month, Rick updates the video listings below. If you would like to learn about new videos, sign up for our free newsletter where we will list the top 20 videos each month.

Any categories in BOLD have sub-categories to help you narrow down your search.

Maintenance Videos (116)

Sort by

Or click here to: Search All Videos


New LAGUNA lathe spindle replacement
By: Kim Tippin Wood Turning
June 12, 2019 · 4,095 views

New Laguna lathe spindle assembly replacement for my NEW Laguna lathe.... yes...NEW. The instructions that I was send is for Jet lathe Belt replacement...... Anyway, I figured it out. Hope you find the process, at the very least, entertaining!! lol I DID!

 

Jet lathe headstock assembly, How to
By: Mike T
May 25, 2019 · 37 views

How to re-assemble the head stock on a Jet JWL-1642EVS lathe

 

Grizzly defective spindle replacement
By: Kim Tippin Wood Turning
April 28, 2019 · 1,003 views

This is a 1 month old BRAND NEW Grizzly 0766 Lathe. The spindle is defective. Grizzly sent PARTS for ME to replace............So..... Before I could get the head stock replaced, I had to attempt to replace the spindle and bearings 1st.... Well, As you can see that was a waste of time. Watch my 'New Laguna Lathe' Video to see how that all worked out... or I should say, didn't work out. If nothing else this video was slightly funny, for me, after it was all over with. Hope you can take something useful from this. Hopefully avoid this situation all together. Thanks you for watching! God Bless!

 

Record Power CL1 upgrade
By: Miss Tee's Woodturning
March 31, 2019 · 82 views

Haydock Converters Speed Genie fitted & working. Full video will be uploaded in the next few days.

 

Jet lathe headstock disassembly, HOW TO
By: Mike T
March 13, 2019 · 249 views

How to disassemble the headstock on a Jet JWL-1642EVS lathe. I am removing the spindle to remove a broken brake collar but it is the same steps if you were replacing the bearings

 

Jim Rodgers, Lesson 9A and 9B, Lathe and Chuck Maint.
By: David Bentley
January 21, 2019 · 193 views

This video is about Jim Rodgers, Lesson 9A and 9B, Lathe and Chuck Maint. This video is about Jim Rodgers, Lesson 9a and 9b, Lathe and Chuck Maint. This video is about lathe maintenance. This video is about chuck maintenance. This video is about Jim Rodgers, lathe and chuck maintenance. How to clean a wood lathe. How to clean a wood chuck. Jame Rodgers Woodturner. Jim Rodgers woodturner.

 

Jim Rodgers, Lesson 9A and 9B, Lathe and Chuck Maint.
By: David Bentley
January 18, 2019 · 32 views

This video is about Jim Rodgers, Lesson 9a and 9b, Lathe and Chuck Maint. This video is about lathe maintenance. This video is about chuck maintenance. This video is about Jim Rodgers, lathe and chuck maintenance. How to clean a wood lathe. How to clean a wood chuck. Jame Rodgers Woodturner. Jim Rodgers woodturner.

 

Tailstock Maintenance for Woodturners
By: Mike Peace Woodturning
January 11, 2019 · 3,727 views

I demonstrate tailstock maintenance and show how to keep your tailstock working smoothly. Sometimes the quill can get damaged which prevents it from advancing or retracting smoothly. I show how to repair using a PM3520b and a Jet Mini as examples. I upload new wood turning videos regularly so Ya’ll come back, hear? Want to support my channel? Check out my Amazon shop https://www.amazon.com/shop/mikepeacewoodturning Disclaimer: If you click on one of the product links, I’ll receive a small commission. This helps support my channel and allows me to continue to make videos like this. Thank you for the support! You can download demonstration handouts, downloadable copies of articles I have published, and other useful woodturning information available on my website http://www.mikepeacewoodturning.com/resources-3/other-woodturning-resources

 

Laguna Revo 1836 Wood Lathe Spindle Lock FIX
By: ThePapa1947
December 26, 2018 · 1,269 views

This is a short video as a Christmas gift for any new lathe owners. I will be posting a wood turning video this Friday. This is for other lathe owners for that may have the same issue. It is a simple fix and you will be glad you did it. I got tired of not having a way of holding the spindle lock in while trying put a bowl blank on or getting a chuck off. So I came up with this solution. It works great for me and I think it would for anyone. Plus it takes no drilling and tapping of your lathe head. This is not a real review but I feel the Laguna is a great lathe for the price. And with working with Laguna with some other small issues they have been great. I give them top rating on that.

 

How to Replace the Drive Belt on the Record Power BS300E, BS350S and BS400 Bandsaws
By: Record Power
December 19, 2018 · 779 views

This short video shows how to replace the drive belt of the BS300E, BS350S and BS400 bandsaws.

 

Replacing the switch on a Jet 1642 Wood Lathe, simple Switch Replacement DIF project
By: Turning Round
December 18, 2018 · 246 views

In this video I am Replacing the Switch on Jet 1642 Wood Lathe. It is a simple process but knowing a few tricks always helps. This is the simple electric switch that turns the lathe on and off. This video shows the process for a Jet 1642 lathe, but it is also so the same process and switch for a powermatic wood lathe. Here is a link to the switch. Telemecanique ZBE-102 Contactor, Black https://www.amazon.com/gp/product/B00DE2CJZU/ref as_li_tl?ie UTF8&camp 1789&creative 9325&creativeASIN B00DE2CJZU&linkCode as2&tag turninground-20&linkId 6af8d704db3d04b05c8a5df354a41903 Telemecanique ZBE-

 

Quick video - lathe maintanance part B
By: smallathe
December 15, 2018 · 40 views

Err... not so quick guys - sorry. In this video I'm taking care of the lathe dials. They are extremely hard to visualize and use - I'm using a trick by painting the dials lines with acrylic paint. This is a well worth project even though it's a time consuming one... Painting the lathe dials allows me to visualize more easily the location of the dials. Hope you enjoy Saar

 

Quick video - lathe maintanance part A
By: smallathe
December 14, 2018 · 57 views

Hi everyone. Between projects I clean the lathe and take care of it - there were two things I wanted to do. I'm discussing issues in lathe rust prevention and protecting the ways. Hope you enjoy.

 

Lathe Maintenance
By: Ian Robbo Robertson
November 29, 2018 · 622 views

This video is how to maintain your lathe so that it performs at its best.

 

Maintain Your Lathe's Tailstock
By: Gord Rock
September 11, 2018 · 1,509 views

A quick look at how to maintain your tailstock to keep it turning easily. Want to support my channel? https://www.buymeacoff.ee/GordRock Link to thread lubricant test: benmlee.com/4runner/threads/threads.htm

 

Stop Rust on Your Wood Lathe
By: Mike Peace Woodturning
August 14, 2018 · 3,139 views

I demonstrate a few tricks for avoiding rust on your lathe and other turning tools. I upload new wood turning videos regularly so Ya’ll come back, hear? Want to support my channel? Check out my Amazon shop https://www.amazon.com/shop/mikepeacewoodturning Disclaimer: If you click on one of the product links, I’ll receive a small commission. This helps support my channel and allows me to continue to make videos like this. Thank you for the support! You can download demonstration handouts, downloadable copies of articles I have published, and other useful woodturning information available on my website http://www.mikepeacewoodturning.com/resources-3

 

# 311 Lathe Care
By: Eddie Castelin
July 23, 2018 · 1,574 views

A couple of basic tips and hints on tools and photos of your work.

 

Here's How I Aligned My Lathe
By: RJBWoodTurner
June 03, 2018 · 4,583 views

The Head and Tail Stock of my lathe always seemed to be our of alignment. A closer inspection revealed three of the four bolts in the head stock were bent. Regards, Bob Preparing Acrylic Blanks for Turning: https://youtu.be/C2TgJRQQK94 Preparing Wood Blanks for Turning: https://youtu.be/gC4GW_a8Zm4 My Info: Facebook: https://www.facebook.com/pages/RJBWoodturner/992853487406788 Instagram: @RJBWoodturner Twitter: @RJBWoodturner E-Mail: RJBWoodturner@ufoww.com Be sure to check out my second channel, WhatchaDoinBob, it’s a VLOG about what I’m doing at any given time. https://www.youtube.com/c/WhatchaDoinBob Address for Shop Stickers: P.O. Box 114 Newburgh, IN 47629-0114

 

Maintenance Of My Lathes Tailstock
By: RJBWoodTurner
May 31, 2018 · 4,005 views

I have been working on my lathe trying to fine tune it and keep up the basic maintenance. Today, I worked on the tailstock. Regards, Bob Preparing Acrylic Blanks for Turning: https://youtu.be/C2TgJRQQK94 Preparing Wood Blanks for Turning: https://youtu.be/gC4GW_a8Zm4 My Info: Facebook: https://www.facebook.com/pages/RJBWoodturner/992853487406788 Instagram: @RJBWoodturner Twitter: @RJBWoodturner E-Mail: RJBWoodturner@ufoww.com Be sure to check out my second channel, WhatchaDoinBob, it’s a VLOG about what I’m doing at any given time. https://www.youtube.com/c/WhatchaDoinBob Address for Shop Stickers: P.O. Box 114 Newburgh, IN 47629-0114

 

I Adjusted The Alignment On My Lathe
By: RJBWoodTurner
May 14, 2018 · 3,363 views

I noticed my lathe was out of Alignment so I made a simple adjustment to correct the issue. Regards, Bob Preparing Acrylic Blanks for Turning: https://youtu.be/C2TgJRQQK94 Preparing Wood Blanks for Turning: https://youtu.be/gC4GW_a8Zm4 My Info: Facebook: https://www.facebook.com/pages/RJBWoodturner/992853487406788 Instagram: @RJBWoodturner Twitter: @RJBWoodturner E-Mail: RJBWoodturner@ufoww.com Be sure to check out my second channel, WhatchaDoinBob, it’s a VLOG about what I’m doing at any given time. https://www.youtube.com/c/WhatchaDoinBob Address for Shop Stickers: P.O. Box 114 Newburgh, IN 47629-0114

 

NOVA FREE Firmware Upgrade for the Voyager DVR 18' Variable Speed Drill Press
By: NOVA Woodworking
May 10, 2018 · 189 views

Free download to upgrade your NOVA Voyager DVR Drill Press Firmware. Watch the video for instructions that will talk you through each step of the process in detail. Go to the link below for download links. Be sure to read all of the instructions before beginning. System Requirements: Windows 10 (and later) deliver the best firmware experience. Previous versions of Windows may work but are not supported by Teknatool. For the firmware upgrade process to go as smoothly as possible, we strongly recommend Windows 10 and later. Download for Apple/Mac is not available at this time. https://www.teknatool.com/product/nova-voyager-firmware-upgrade

 

I Built A Reverse Switch For My Lathe.
By: RJBWoodTurner
April 08, 2018 · 3,056 views

This video is not meant to teach you how to reverse your lathe. It simply documents what I did to reverse mine. If you choose to attempt this, you do so at you're own risk. My recommendation would be to seek the help of a professional electrician. Regards, Bob Preparing Acrylic Blanks for Turning: https://youtu.be/C2TgJRQQK94 Preparing Wood Blanks for Turning: https://youtu.be/gC4GW_a8Zm4 My Info: Facebook: https://www.facebook.com/pages/RJBWoodturner/992853487406788 Instagram: @RJBWoodturner Twitter: @RJBWoodturner E-Mail: RJBWoodturner@ufoww.com Be sure to check out my second channel, WhatchaDoinBob, it’s a VLOG about what I’m doing at any given time. https://www.youtube.com/c/WhatchaDoinBob Address for Shop Stickers: P.O. Box 114 Newburgh, IN 47629-0114

 

Broken indexing locking pin fix by Al Furtado
By: Al Furtado Rebel Turner
April 06, 2018 · 2,076 views

Broken indexing locking pin fix Woodturning tutorials as well as tool modifications

 

Lathe Restoration Zyto Part 1 Tail Stock
By: MG Makes
March 24, 2018 · 542 views

Welcome back folks, This is Part One of a series documenting the restoration process of my vintage metal working lathe, this is a Zyto Brand. these were manufatured in the Uk from around the 1930's In Part one i remove the tail stock and strip it of all componant parts, degrease, remove the old paint, wire brush and rebuild. Whilst this is not a sponsered build i would like to give a shout out to Wilkos Paint and Varnish remover - for 3 It works like a dream as you can see. i will leave a link below.. https://goo.gl/Xo4cmR Makers Media Network Public Facebook Page https://www.facebook.com/MakersMediaNetwork Makers Media Network You tube Channel https://www.youtube.com/channel/UCbjYrhnIA3p1G6h15QCEidg Thanks for watching

 

It Worked !!! I was Able To Repair My Lathe Control Box
By: RJBWoodTurner
February 06, 2018 · 2,774 views

Once I figured out what I was doing wrong, everything fell into place and I was able to get the control box of my lathe working again. Time to source a Di-Pole switch and add reverse. Thank you to everyone who helped me figure this out. Regards, Bob Preparing Acrylic Blanks for Turning: https://youtu.be/C2TgJRQQK94 Preparing Wood Blanks for Turning: https://youtu.be/gC4GW_a8Zm4 My Info: Facebook: https://www.facebook.com/pages/RJBWoodturner/992853487406788 Instagram: @RJBWoodturner Twitter: @RJBWoodturner E-Mail: RJBWoodturner@ufoww.com Be sure to check out my second channel, WhatchaDoinBob, it’s a VLOG about what I’m doing at any given time. https://www.youtube.com/c/WhatchaDoinBob Address for Shop Stickers: P.O. Box 114 Newburgh, IN 47629-0114

 

My First Attempt At Reparing The Control Box Is A Fail!
By: RJBWoodTurner
February 05, 2018 · 1,776 views

Attempt One Was A Fail! I missed plugging the power out cable into the control box. That means the first chip could have been the fix. Now, we'll never know. Regards, Bob Preparing Acrylic Blanks for Turning: https://youtu.be/C2TgJRQQK94 Preparing Wood Blanks for Turning: https://youtu.be/gC4GW_a8Zm4 My Info: Facebook: https://www.facebook.com/pages/RJBWoodturner/992853487406788 Instagram: @RJBWoodturner Twitter: @RJBWoodturner E-Mail: RJBWoodturner@ufoww.com Be sure to check out my second channel, WhatchaDoinBob, it’s a VLOG about what I’m doing at any given time. https://www.youtube.com/c/WhatchaDoinBob Address for Shop Stickers: P.O. Box 114 Newburgh, IN 47629-0114

 

Jet 1220 lathe knocking sound - trouble shooting
By: Eric Godwin
January 01, 2018 · 163 views

This is a video on how to fix the knocking sound coming from a jet 1220 wood lathe.

 

Getting a Seized Chuck Off a Wood Lathe
By: Mike Peace Woodturning
December 12, 2017 · 4,180 views

I demonstrate how to get a seized chuck of a wood lathe. More importantly, I show you how to prevent this from happening. I upload a new wood turning tip every Tuesday and a wood turning tutorial video each and every Friday so Ya’ll come back, hear? Want to support my channel? Check out my Amazon shop https://www.amazon.com/shop/mikepeacewoodturning Disclaimer: If you click on one of the product links, I’ll receive a small commission. This helps support my channel and allows me to continue to make videos like this. Thank you for the support! You can download demonstration handouts, downloadable copies of articles I have published, and other useful woodturning information available on my website http://www.mikepeacewoodturning.com/resources-3

 

Replacing The Variable Speed Control Box On My Lathe
By: RJBWoodTurner
December 09, 2017 · 4,261 views

The new control box arrived, I installed it and its working great. Regards, Bob Preparing Acrylic Blanks for Turning: https://youtu.be/C2TgJRQQK94 Preparing Wood Blanks for Turning: https://youtu.be/gC4GW_a8Zm4 My Info: Facebook: https://www.facebook.com/pages/RJBWoodturner/992853487406788 Instagram: @RJBWoodturner Twitter: @RJBWoodturner E-Mail: RJBWoodturner@ufoww.com Be sure to check out my second channel, WhatchaDoinBob, it’s a VLOG about what I’m doing at any given time. https://www.youtube.com/c/WhatchaDoinBob Address for Shop Stickers: P.O. Box 114 Newburgh, IN 47629-0114

 

My Second Attempt As Casting - What Went Wrong What Went Right
By: RJBWoodTurner
December 06, 2017 · 9,722 views

My second attempt at casting had a small issue caused by me. My third and fourth attempts were perfect. Regards, Bob Preparing Acrylic Blanks for Turning: https://youtu.be/C2TgJRQQK94 Preparing Wood Blanks for Turning: https://youtu.be/gC4GW_a8Zm4 My Info: Facebook: https://www.facebook.com/pages/RJBWoodturner/992853487406788 Instagram: @RJBWoodturner Twitter: @RJBWoodturner E-Mail: RJBWoodturner@ufoww.com Be sure to check out my second channel, WhatchaDoinBob, it’s a VLOG about what I’m doing at any given time. https://www.youtube.com/c/WhatchaDoinBob Address for Shop Stickers: P.O. Box 114 Newburgh, IN 47629-0114

 

Lathe Update - Parts On Order
By: RJBWoodTurner
December 05, 2017 · 2,465 views

Parts are on order. Regards, Bob Preparing Acrylic Blanks for Turning: https://youtu.be/C2TgJRQQK94 Preparing Wood Blanks for Turning: https://youtu.be/gC4GW_a8Zm4 My Info: Facebook: https://www.facebook.com/pages/RJBWoodturner/992853487406788 Instagram: @RJBWoodturner Twitter: @RJBWoodturner E-Mail: RJBWoodturner@ufoww.com Be sure to check out my second channel, WhatchaDoinBob, it’s a VLOG about what I’m doing at any given time. https://www.youtube.com/c/WhatchaDoinBob Address for Shop Stickers: P.O. Box 114 Newburgh, IN 47629-0114

 

This is the final follow up to my lathe problems.
By: RJBWoodTurner
December 03, 2017 · 3,059 views

I believe I will order a replacement board on Monday from PSI. Regards, Bob

 

Testing all the Suggestions I got for Repairing my Lathe
By: RJBWoodTurner
December 02, 2017 · 2,004 views

With your help, I think I've identified the issue with my lathe. Regards, Bob

 

I'm Having Trouble With The Variable Speed On My Lathe
By: RJBWoodTurner
December 01, 2017 · 1,979 views

Tonight my lathe started surging and there was a burning smell coming from the Variable Speed box. If you know about electronics and have any suggestions, I'd love to hear them. Regards, Bob

 

Lathe Fix and Review, Plus Shop Tour, # 100
By: The Wood Whirler
September 30, 2017 · 2,001 views

Had a problem with my lathe, human induced. I show how I fix it, then review the lathe and show off my shop. I MISS-SPEAK ABOUT THE LOW RPM, IT IS 56 NOT 6 AS I SAID, SORRY. Check out my grandson's site. squareup.com/store/aturnedworld

 

#39 How to Repair a Broken Lathe With Duct Tape - Level: Wood Wizard
By: Austringer Creations
September 22, 2017 · 415 views

I got a catch while turning a 12' poplar bowl on my HF wood lathe and the head broke completely off the bed. How does a humble wood butcher with limited funds make repairs?... DUCT TAPE of course!!!! Actually, the repair was quite simple, the clamping system for the rotating lathe head uses a small rolled pin in a high-stress location and the catch cause the pin to shear in half allowing the clamp to open up and the head departed the bed. I just replaced it with a 4mm stainless steel screw and reassembled the lathe. Gooder 'n new!

 

Refresh Your Wood Lathe
By: SP Wood Art
August 25, 2017 · 3,719 views

In this video I replace and upgrade some wood lathe parts to refresh and/or enhance my wood lathe. I currently use a PSI (Pen State Industries) wood lathe which I've had for many years and enjoy this lathe. Many of the topics in this video will relate to several types/brands of wood lathes. I hope you enjoy this video. If you would like see more of SP Wood Art visit us at: www.spwoodart.com Our Webpage www.facebook.com/spwoodart www.plus.google.com/ SPWoodArt1/about www.pinterest.com/spwoodart/ I strive to create handmade, high quality wood pieces (and sometimes, crafts using other mediums

 

Cleaning Morse Tapers - Quick Tip
By: Lisburn Wood Works
July 30, 2017 · 828 views

Keep your morse tapers clean. Note: make sure you choose the correct size for your lathe's tapers. Link to the product I'm discussing: https://www.woodturnerscatalog.com/p/90/3651/TaperMate-Morse-Taper-Cleaner

 

Wood Turning - How to change the drive belt and bearings on the Axminster AT1628VS
By: Mike Waldt
July 26, 2017 · 9,426 views

I go through MY method of changing the drive belt and bearings on the Axminster AT1628VS.

 

Belt ratio change
By: Bostin Bowls
July 16, 2017 · 44 views

 

Fixing the Lathe Belt and Wheels
By: CL Woodturning
July 10, 2017 · 196 views

 

Wood Turning - Basic Lathe Maintenance #2 Bedways, Banjo,Tailstock and Headstock
By: Mike Waldt
June 30, 2017 · 8,116 views

UKIWS: http://www.ukiws.co.uk/ Yorkshire Grit: http://yorkshire-grit.com/ Hampshire Sheen: http://www.hampshiresheen.com/ Simon Hope: http://www.hopewoodturning.co.uk/ Euan McKinnons FB Page: https://www.facebook.com/search/top/?q euan%27s%20woodturning%20and%20woodworking Mike Peace's Channel: https://www.youtube.com/user/mpax356

 

Wood Turning - Basic Lathe Maintenance - #1 The Tailstock Quill
By: Mike Waldt
June 23, 2017 · 7,501 views

I go through my Tailstock Quill maintenance process, to keep your Tailstock working perfectly. UKIWS: http://www.ukiws.co.uk/ Yorkshire Grit: http://yorkshire-grit.com/ Hampshire Sheen: http://www.hampshiresheen.com/ Simon Hope: http://www.hopewoodturning.co.uk

 

Frankenlathe Harbor Freight Lathe Rebuild
By: Turntastic Wood Designs
May 26, 2017 · 8,734 views

Rebuild of a Harbor Freight lathe using a treadmill motor

 

Record CL4 lathe - Bearing maintenance
By: Turning Works
April 02, 2017 · 5,655 views

This is a video to (hopefully) explain how to take apart a CL4 lathe spindle and bearing. If you need to change your pulley belt, then watch this video!

 

Woodturning at 54a. #110, Lathe Riser Blocks
By: Keith Barrow
January 27, 2017 · 7,832 views

No turning in this video,just a simple addition to the lathe which will allow larger pieces.

 

VFD upgrade part 3 by Al Furtado
By: Al Furtado Rebel Turner
December 17, 2016 · 1,763 views

This is VFD Upgrade part 3. I mount the VFD and go over options. I discuss and show the wiring as well as the complications. I discuss wiring as well as display the wiring needed for a successful install. This is a very informative Tutorial for anyone that is using a lathe that speed is changed by changing belt/pulleys and giving you a much safer range of speeds. I hope you enjoy and please comment. Follow me on FB https://www.facebook.com/yournamegoeshere2 Twitter https://twitter.com/AlbertFurtado57

 

VFD upgrade part 2 by Al Furtado
By: Al Furtado Rebel Turner
December 09, 2016 · 2,117 views

This is part 2 of 3 VFD upgrade. On this video I go over will be basic wiring and instillation Part 3 will be external controllers and finalizing operations

 

VFD upgrade part 1 by Al Furtado
By: Al Furtado Rebel Turner
December 06, 2016 · 3,011 views

This is part 1 of 3 of a VFD Upgrade. on this video I go over expected pricing, I discuss other options that might suit you with a countershaft and go over VFD expectations and pulley speeds vs. torque. Part 2 will be basic wiring and instillation Part 3 will be external controllers and finalizing operations

 

04 - Upgrade Harbor Freight Lathe to Link Belt
By: Bill Rockwood
October 01, 2016 · 29,533 views

In this video I replace the stock belt with a link belt. Power-Twist link belt can be found at Fenner Drives (http://www.fennerdrives.com/powertwist-plus/_/PowerTwist-Plus-3L/? ), Grizzly (http://www.grizzly.com/products/Power-Twist-V-Belt-3-8-x-2-m/T21991?utm_campaign zPage), and other places.

 

ROCKWELL HARDNESS Scale in woodworking and woodturning: Sam Angelo
By: WYOMINGWOODTURNER
August 31, 2016 · 4,733 views

With so many variations on High Speed steel, understanding tool quality can be confusing. Sam has provided some simple detailed information on the Rockwell Hardness scale. Measuring the hardness in tool steel is information that helps woodworkers and woodturners decide which tool to purchase. This link offers more information on the Rockwell hardness scale: http://www.leevalley.com/us/shopping/TechInfo.aspx?p 45616

 

Ремонт подручника для токарного станка
By: Аleksey Bek
August 10, 2016 · 1,169 views

Отломилась ось подручника для токарного станка по дереву. Можно было сделать новый, но я решил восстановить родной. С помощью токарного ТВ-4 вытачиваю новую ось и собираю. Надеюсь получился вполне рабочий подручник.

 

Achsausrichtung einwandfrei. Drechselbank JET JWL-1221VS
By: GentleTurn
July 08, 2016 · 2,346 views

Die Genauigkeit der Drehachsen zwischen den Spitzen sowie mit längerem Holz wurde überprüft. Wäre das Zusammenspiel der Komponenten nicht einwandfrei, so wäre die Abweichung bei dem langen Holz deutlich sichtbar. Gleiches gilt bei der Zusammenführung der Spitzen ohne Werkstück. Der sog. Drechslerkuss ist bei dieser Maschine einwandfrei. Dabei hat sie durch meine Ungeschickthet so manchen Schlag aushalten dürfen. Soziale Medien / Social Media YouTube: https://www.youtube.com/c/gentleturn Instagram https://www.instagram.com/gentleturn/ Facebook: https://www.facebook.com/Ge

 

Harbor Freight Lathe 34706 Fixes and Upgrades
By: Braxton Wirthlin
June 17, 2016 · 52,192 views

Harbor Freight Lathe 34706 fixes and upgrades I had recently been having some problems with my lathe so I thought I'd making a video showing how I fixed them in hopes it would help some people out. I use a Harbor Freight 34706 lathe and have had it for about 2 1/2 years. I show you how to change the belt, fix a problem with the tool rest, clean and wax the bed, and also do some work to the tool rest so your tool will slide easier. 3L240 belt - http://amzn.to/23fLnrA 4L240 belt - http://amzn.to/23fKj75 chuck on the lathe - http://amzn.to/2gVK0zM Paste wax - http://amzn.to/21q8Gh0 Sander - h

 

Делаем для токарного лючок
By: Аleksey Bek
May 19, 2016 · 766 views

Способ изготовления ревизионного лючка для токарного станка. Делаем круг диаметром 135 мм из металла толщиной 2 мм на токарном станке.

 

'Энкор Корвет - 75 М' в собранном виде.
By: Аleksey Bek
May 03, 2016 · 1,291 views

Наконец закончил все работы по модернизации токарного станка. Сохранил все его первоначальные параметры, изменив только передачу от электродвигателя на вариатор. Надеюсь, что теперь он будет служить без частых поломок. Finally finished all the work on the modernization of the lathe. Retains all its original parameters, changing only the transmission from the motor to the variator. I hope that he will serve without frequent breakdowns.

 

Охлаждение электродвигателя токарного станка
By: Аleksey Bek
May 01, 2016 · 4,697 views

Охлаждение электродвигателя немаловажный фактор его работы. Если будет неудовлетворительное охлаждение, двигатель будет греться и долго не прослужит. Показываю свой вариант решения. The cooling of the motor is important factor of his work. If there is poor cooling, the engine will warm up and will last a long time. Show your solution.

 

Lathe Riser Blocks
By: Kyle Toth
April 28, 2016 · 65,550 views

This video is about the making of lathe riser blocks. Suscribe to my channel https://www.youtube.com/user/HomedepotKt For inquiries and commissions contact woodbytoth@gmail.com To keep up with my work throughout the week check out the links below. Thanks for watching! Love Tōth Also if you want to know why I love what I do check out my artist profile video done by Vigil Films. Its part of there Ardent Collection.... http://youtu.be/JjUzuECZN-0 http://www.woodbytoth.com https://m.facebook.com/woodbytoth https://mobile.twitter.com/woodbytoth http://instagram.com/tothtoth Support: https://www.patreon.com/woodbytoth Store: http://woodbytoth.bigcartel.com For a Dusty Life T-Shirt check out https://thedustylife.com

 

Модернизации Энкор Ковет-75 первый пуск
By: Аleksey Bek
April 24, 2016 · 2,002 views

Собрал новый привод станка, осталось сделать кожух и небольшие регулировки и подгонки. Показываю первый пуск токарного станка после модернизации.

 

New Lathe in the shop
By: Al Furtado Rebel Turner
April 22, 2016 · 13,815 views

There is a new lathe in town. This video is not a wood turning video but one that goes into some detail on adding riser blocks to increase the capacity of a belt driven lathe, Also I show some common fixes to that could help out in your situation. I rebuild a Delta wood-lathe-46-221 to what I think is better than factory in some areas.

 

Woodturning With The Naked Turner Quick Look At Powermatic Problem
By: Erik Anderson
April 14, 2016 · 2,726 views

A quick look at a problem I had with my remote switch for my Powermatic 4224b Here is a link to a fix I saw on the interweb and David England a subscriber sent me a link to it. http://lumberjocks.com/PASs/blog/38863

 

Conversion de VFD Hitachi L-100 en Vicmarc VL-100
By: Adam Woodturner
April 13, 2016 · 1,134 views

Conversion de VFD Hitachi L-100 en Vicmarc VL-100 aun faltan algunos ajustes pero ahi vamos.

 

Wood Turning - Chuck and Jaw Set Up and Maintenance
By: Mike Waldt
March 21, 2016 · 56,725 views

Some hints and tips on Chuck and Jaw set up and maintenance. UKIWS - http://www.ukiws.co.uk/ UKIWS on Facebook - https://www.facebook.com/ukiws

 

Ремонт токарного станка Энкор Корвет 75
By: Аleksey Bek
March 21, 2016 · 1,246 views

Демонтаж со станины и ремонт передней бабки токарного Энкор Корвет 75. Замена передающего вращательный момент зубчатого ремешка. Сборка и установка на станок.

 

Обзор токарного по дереву Энкор Корвет 75
By: Аleksey Bek
March 20, 2016 · 7,323 views

Обзор токарного станка Энкор Корвет 75. Все достоинства и недостатки. Необходимость в доработках.

 

Lathe Start Up Repair
By: JW Woodturning
March 17, 2016 · 1,601 views

My Lathe has been starting slower and slower. In this video I change out the motor start capacitor to see if I can solve the problem. My Website: http://www.jwwoodturning.co.uk Folksy page: https://folksy.com/shops/JWWoodturning Music: http://www.purple-planet.com

 

VFD lathe conversion by Al Furtado
By: Al Furtado Rebel Turner
January 10, 2016 · 4,026 views

I had enough of belt changing speed on my lathe Upgrade to a VFD good source for those of you wanting one is http://dealerselectric.com/motor_drive_packages.asp

 

woodturning # 27 repair lathe variable speed handle
By: Woodslee Summercraft
January 10, 2016 · 1,012 views

A repair to my lathe speed control function that didnt cost that much money. King Canada make the same basic model as my lathe so I found a retailer and purchased the part from them, below is a link to free online service manuals. I hope this helps http://powertool.manualsonline.com/manuals/mfg/king_canada/king_canada_lathe_product_list.html

 

General Wood Lathe Maintenance and A Repair
By: SP Wood Art
December 02, 2015 · 7,022 views

This video is comprised of general wood lathe maintenance, in addition to, a much needed, over due repair. I also cover maintaining wood lathe tool rests, drive centers, and live centers. The wood lathe used in this video is a PSI (pen state industries) Turncrafter commander variable speed lathe. If you would like see more of SP Wood Art visit us at: www.spwoodart.com www.facebook.com/spwoodart www.plus.google.com/ SPWoodArt1/about www.pinterest.com/spwoodart/ I strive to create handmade, high quality wood pieces (and sometimes, crafts using other mediums such as natural stone or acrylic) th

 

#152 Grizzly G0766 actualizacion del banjo
By: Miguel Sanchez
November 30, 2015 · 8,526 views

Ayuda al canal: www.patreon.com/miguelsanchez Help the channel: www.patreon.com/miguelsanchez http://www.facebook.com/profile.php?id 1181903663 http://www.tornoartesano.es miguel@tornoartesano.es

 

Grinding Wheel Maintenance
By: Peter Stewart
November 28, 2015 · 2,817 views

This video shows how I take care of my grinding wheels. ---------------------------------------------------------- If you would like a sticker, send me a stamped self addressed envelope or one of your own stickers with your address. Peter Matthew 6388 East Executive Drive Westland, MI 48185 ----------------------------------------------------------- Contact me: peterturnswood@gmail.com My eBay store: http://www.ebay.com/usr/dste6080 Subscribe to my YouTube Channel! I post videos every Friday!

 

Shit! My lathe still wobbles
By: Corpus Woodworks
November 17, 2015 · 1,297 views

 

Lathe restoration: First testrun
By: Corpus Woodworks
October 31, 2015 · 61 views

Figured I'd try a testrun between centers, without a chuck. Seems to work quite allright. Turned a little spinning top from a scrap of purperheart. Check out my facebook for some photo's of the restaurationprocess. https://www.facebook.com/C4-Woodworks-188259937880853

 

Lathe restoration: New Axle installed
By: Corpus Woodworks
October 31, 2015 · 90 views

My new axle was finished this week. Got to installing and aligning today. This is the first testrun, only forgot to tighten the belt at the highest speed. https://www.facebook.com/C4-Woodworks-188259937880853

 

Lathe Restoration Slideshow part one
By: Corpus Woodworks
October 11, 2015 · 133 views

Slideshow of a series of photo's about the restauration of my old lathe. Part two will be added as soon as I have my new axle. All parts have been stripped of their paint, primed and refinished. All bare metal parts have been cleared of any paint and rust and have been either oiled for sliding parts or clearcoated for fixed parts. https://www.facebook.com/C4-Woodworks-188259937880853

 

Broken Tail stock on mini lathe
By: Gabe Castro
October 06, 2015 · 677 views

How to fix broken tailstock on mini lathe.

 

#244 Lathe care and more
By: Eddie Castelin
August 30, 2015 · 299 views

This video is about lathe bed care

 

Lathe Chuck Maintenance
By: Daniel Vilarino
July 07, 2015 · 8,096 views

Hola/Hi! Este video está en Inglés. Si prefieres verlo en Español haz un click en el siguiente enlace: http://youtu.be/ZqvYeMNZ0m4 ***This video is in English*** En este video, limpio, lubrico y trato de reparar el mandril de garras de mi torno de madera. Había quedado un pelito descentrado con una agarrada fuerte, y para resolver el problema decidí, desarmarlo y volver a armarlo, limpiando, aceitando y ajustando las piezas. ***In this video, I clean, lubricate and try to repair my jaws chuck. It was doing a bit of a wobble after a serious catch. To solve the issue I decided to disassemble,

 

Mantenimiento del Mandril de Garras
By: Daniel Vilarino
July 07, 2015 · 23,429 views

Hola/Hi! ***This video is in Spanish, if you prefer to see it in English, please click in the following link: http://youtu.be/2VqyvRbcLYo*** Este video está en Español. En este video, limpio, lubrico y trato de reparar el mandril de garras de mi torno de madera. Había quedado un pelito descentrado con una agarrada fuerte, y para resolver el problema decidí, desarmarlo y volver a armarlo, limpiando, aceitando y ajustando las piezas. ***In this video, I clean, lubricate and try to repair my jaws chuck. It was doing a bit of a wobble after a serious catch. To solve the issue I decided to disass

 

#244 Lathe care and more
By: Cap'n Eddie Castelin
July 01, 2015 · 10,485 views

This video is about lathe bed care

 

Bend in headstock or just bearings?
By: Cook Crafted Workshop
June 20, 2015 · 83 views

 

#16 Project Update and Lathe Rant / Fix
By: Yuval Lahav Woodturning
June 07, 2015 · 2,199 views

I'm explaining why I don't have a new video this week, and also show you my new little handles I got for the lathe. Patreon: https://www.patreon.com/YuvalLahav Instructables: http://www.instructables.com/member/yuvallahav/ Pinterest: https://it.pinterest.com/yuvallahav/ Facebook: https://www.facebook.com/yuval.lahav.16 Reddit: https://www.reddit.com/user/aforeignitalian/ Feel free to share and recommend this video to your friends and family, a thumbs up would be appreciated, and if this is your first time to my channel, you are most welcome to subscribe!

 

Supernova 2 woodturning chuck: Maintenance
By: Hendrik van Taak
May 02, 2015 · 3,080 views

Description: How to dissemble the chuck, lubricate and assemble.

 

Woodturning - Motor Repair - Start Capacitor
By: Kevin Krull
March 30, 2015 · 4,278 views

For this latest installment of Tips and Techniques I tackle an ill running motor. The motor was making a buzzing sound and would not rotate the piece is was turning without assistance. By researching online, I tracked the problem down to the start capacitor, so I ordered one. 7 dollars later, my lathe is up and running!

 

#66 Woodturning Lathe and Scroll Chuck Maintenance
By: Stephen Ogle
March 10, 2015 · 9,929 views

My process for keeping my lathe in good shape along with my Scroll Chucks. At the end I give a description of how I built my Rocket Stove to answer a viewer's comments about it.

 

Welding repairs to HSS turning tools
By: BowlsByCharles
March 07, 2015 · 492 views

I had a couple of tools that broke at the shank. They were HSS and didn't know how they would take to welding with carbon steel rod. Also wanted to improve the shank thickness and length. So this is an experiment with welding carbon steel to high speed steel.

 

New countershaft design by Al Furtado
By: Al Furtado Rebel Turner
March 05, 2015 · 961 views

Wood turning tutorials as well as tool modifications a mishap on my lathe forced me back to the drawing board and come up with an improved countershaft design.

 

#7 G0632 DC drive explination
By: DIY with Uncle Cy
February 24, 2015 · 1,793 views

Answering Questions about my G0632 that I converted to a DC treadmill motor. Explaining my homemade indexing jig for it. And an overview of the 1941 Powr-Kraft lathe and how I adapted a reeves drive for it.

 

Changing Belt on Mini Lathe (Clone Jet Lathe)
By: Gabe Castro
January 23, 2015 · 2,771 views

Belt change on M Power Mini Lathe. Click on link to buy replacement belt: http://amzn.to/2x7RQer

 

Why I I'd been away and some Lathe Motor Maintenance
By: PeteTGIF
January 23, 2015 · 959 views

Sorry for being away from YouTube for a while, but some of you might know, when there's some life over at the end of your money, you have to focus on more important things than woodworking, especially in the cold wintertime. A big thank you to all my subscribers who commented on my videos. This gives me the needed input for my inspirations. Special thanks to Robbie The Woodturner for the awesome bowl gouges! https://www.youtube.com/user/Robbiethewoodturner Vic Armstrong for the digital calipers he sent me, now I've got a nice tool to measure metrics and imperial! Christopher Fischer for the aw

 

Wood lathe countershaft and restoration by Al Furtado
By: Al Furtado Rebel Turner
January 12, 2015 · 1,185 views

I made this new countershaft in order to get a slower speed on my lathe as well as increase torque I also took this opportunity to give the lathe a fresh look. links to pulley speeds http://www.gizmology.net/pulleysbelts.htm http://gadi.agric.za/software/renting/pulley_calc.php

 

Concentricity, Runout and Woodturning Accuracy
By: WildWood Design
January 10, 2015 · 4,165 views

This video describes runout, concentricity and how debris and cleanliness can affect wood turning accuracy.

 

Tailstock Upgrades
By: Custom Chris
December 06, 2014 · 10,727 views

PSI Live center and drill chuck https://famebit.com/u/CustomChris For entertainment purposes only music by Kevin MacLeod (incompetech.com)

 

Jet 1221vs lathe clicking noise.
By: Aaron Meredith
November 30, 2014 · 2,324 views

Jet 1221vs lathe. Reverse has a clicking noise at slow speeds in reverse. Not sure if this is the brushes or not. The noise is definitely coming from the motor. Any comments appreciated.

 

Torneando Madera Con Mario Cantarutti
By: TORNEANDO MADERA CON MARIO CANTARUTTI
November 29, 2014 · 9,983 views

Aquí verán algunos trabajos realizados en madera. Espero que les guste! Saludos!

 

TGIF Shop Update #002 - Maintenance on Threads
By: PeteTGIF
October 09, 2014 · 488 views

Ever once in a while you encounter the problem, that you can't tighten the banjo enough to keep it stable on your lathe bed. It's also hard to turn a nut on a bolt. You might not be able to fix this problem by lubricating the threads, because the reason for the problem lies in between the threads! You got some compressed sawdust. I show you my way to fix the problem and how to use a lubricant on bolts. For the ones who got a similar lathe or tool like mine, please feel free to ask any questions, regarding tool maintenance. I'll try to answer, either in a comment or in a new video. Music Funkorama by Kevin McLeod, http://www.incompetech.com Lizenz Creative Commons 3.0 http://creativecommons.org/licenses/by/3.0/deed.de

 

adjustment knob for mazzer grinder on the wood lathe
By: Jamie Pinner
September 12, 2014 · 134 views

 

Refinishing a Wood Lathe Part 3: Painting
By: Peter Stewart
July 25, 2014 · 1,418 views

Thanks for watching! Subscribe for new woodworking videos every Friday!

 

Refinishing a Wood Lathe Part 2: Cleaning and Priming
By: Peter Stewart
July 25, 2014 · 1,077 views

Part 3: https://www.youtube.com/watch?v gFg7Zl0&list UUMCVIk6zuSQNsbhdcPhfiBA&index 1

 

Refinishing a Wood Lathe Part 1: Sanding
By: Peter Stewart
July 25, 2014 · 1,704 views

Part 2: https://www.youtube.com/watch?v etyA6j3oXC4&list UUMCVIk6zuSQNsbhdcPhfiBA Part 3: https://www.youtube.com/watch?v gFg7ZIoZGl0&list UUMCVIk6zuSQNsbhdcPhfiBA&index 1

 

Craftsman Lathe Restoration Part 1
By: Custom Chris
July 16, 2014 · 8,047 views

Old 1950's Craftsman lathe restoration

 

Craftsman Lathe Restoration Part 2
By: Custom Chris
July 16, 2014 · 9,487 views

Old 1950's Craftsman lathe restoration

 

Easy wood lathe riser blocks
By: Al Furtado Rebel Turner
July 13, 2014 · 5,957 views

Easy wood riser blocks and a few other adjustments allow you to turn a 16' bowl on a 12' lathe this project would cost under 20 dollars and doable in a couple of hours. This could possibly be the best lathe upgrade you can do but as always follow safety especially when you are modifying a piece of equipment from the way it was designed by the manufactures' specifications. The use of a reduction gear is a must before you can turn a large piece on this lathe as the smallest speed on it was too fast even for the largest it was capable of turning. Enjoy.

 

Cleaning My Jet 1642 Lathe Ways with a Rust Remover
By: Turning Round
May 12, 2014 · 10,916 views

In this video I use some Naval Jelly to clean and restore the ways on my Jet 1642 Lathe. I am trying the product for the first time and I have heard great reviews. I was expecting a crystal clear shinny finish rust free, what I ended up with was a dull streaked rust free surface. I guess it did the job but I may need to try this again for a super clean finish.

 

#95 Toca limpiar - Let s clean
By: Miguel Sanchez
April 29, 2014 · 8,932 views

Ayuda al canal: www.patreon.com/miguelsanchez Help the channel: www.patreon.com/miguelsanchez Es hora de limpiar el taller y no respirar el serrin fino. http://www.facebook.com/profile.php?id 1181903663 http://www.tornoartesano.es miguel@tornoartesano.es

 

Lathe Maintenance - Mike Ilkiw
By: Woodturners of Southwest Missouri
December 05, 2013 · 5,029 views

Mike Ilkiw of the Woodturners of Southwest Missouri gives us some tips on maintaining our lathes. Visit us at woodturnersofswmo.org

 

#55 Lidiando con las virutas (resubido)
By: Miguel Sanchez
October 26, 2013 · 13,518 views

Ayuda al canal: www.patreon.com/miguelsanchez Help the channel: www.patreon.com/miguelsanchez Un pequeño añadido facil de hacer a coste cero con lo que tenemos por el taller y que tiene buena utilidad, Espero que os guste. http://www.facebook.com/profile.php?id 1181903663 http://www.tornoartesano.es miguel@tornoartesano.es

 

#61 Mantenimiento del torno
By: Miguel Sanchez
October 21, 2013 · 17,432 views

Ayuda al canal: www.patreon.com/miguelsanchez Help the channel: www.patreon.com/miguelsanchez El mantenimiento de nuestro torno es fundamental, esta es la forma en que yo mantengo el mio. http://www.facebook.com/profile.php?id 1181903663 http://www.tornoartesano.es miguel@tornoartesano.es

 

Tool Rest Maintenance
By: woodturningwithtim1
August 04, 2013 · 7,263 views

Is your tool rest looking a little worse for wear? Tim shows you how to return it to its former glory and how to maintain that nice smooth surface.

 

Woodturning Q&A Tool Rest Maintenance
By: The Woodshop
March 05, 2013 · 11,235 views

In this video I talk about Maintaining your lathe tool rest. Ways you can support the show Schedule one-on-one online classes jacobson68@yahoo.com ChefwareKits http://www.chefwarekits.com/easy-wood-tools?tracking carleasy Easy Wood Tools http://www.easywoodtools.com/ Website http://www.thewoodshop.tv/ Google https://plus.google.com/113199904565893027390#113199904565893027390/posts Facebook https://www.facebook.com/pages/The-WoodshopTV/161892940583516?ref hl Welcome to my channel, I have a new project video every Friday with wood turning tips and projects. Taking you from start to finish with a ruff piece of wood to your sanded and finished project.

 

Jet JWL 1442 VS reeves drive 2 of 2
By: Adam Woodturner
February 18, 2013 · 5,120 views

Issues with the belt

 

Jet JWL 1442 reeves drive issue 1 of 2
By: Adam Woodturner
February 18, 2013 · 15,000 views

Jet JWL 1442 reeves drive issue Belt and noise changing speeds

 

You gotta get dirty to make it purdy
By: Jake Gevorgian
July 14, 2012 · 2,656 views

creating flat surface on the tool rest.

 

Gershwin Woodcraft reviews his modification to the Jet 1220 Lathe
By: Phil Gershwin
April 15, 2012 · 3,344 views

Gershwin Woodcraft reviews some simple modification to a Jet Mini lathe to make it more comfortable to work with.

 

Pen Mandrel Maintenance
By: TurnunChips
February 07, 2012 · 2,896 views

fixing concentricity in a pen mandrel

 

How I check the RPM of the Wood Lathe
By: Jake Gevorgian
November 25, 2011 · 39,125 views

In this video I'm using a Digital Laser Tachometer to check the RPM of my woodlathe. Sorry for the bad quality of both, sound and image, I was using my iPhone to shoot this... Here is where I got it from http://www.amazon.com/Digital-Photo-Laser-Tachometer-Contact/dp/B001N4QY66

 

Return to Turning Videos

Powered by Google

Our Monthly Update

We update our home page about monthly to feature a new project, a new article, and a new and hot tool. Then we send an email to alert our subscribers.
We never let anyone use our list, and our subscribers have been wonderfully loyal as a result.

We hope you will try it out!

Sign Up For Our Newsletter

A Sampling of our Sponsors:
(Visit the Vendor's Corner above to see all our sponsors)

Stainless Steel Bottle Stoppers
Flutemaster
Woodturner's Tools

(Click any Ad to go to our Sponsor's Website)